Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › RELAY › from 2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052095 RELAY G

1KD-FTV ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 3.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F)

a.
B060778
2.042,0.729 1.688,0.333 false 2.625,0.729 2.99,0.365 false 2.354,1.104 3,0.948 false 2.354,1.604 3,1.479 false 1.573,0.24 1.802,0.417 0.229,0.177 10 1 3.01,0.271 3.24,0.49 0.229,0.219 10 2 3.021,0.885 3.344,1.042 0.323,0.156 10 5 3.021,1.365 3.24,1.521 0.219,0.156 10 3 1.167,0.76 1.406,0.938 0.24,0.177 10 5 1.167,1.292 1.354,1.479 0.188,0.188 10 2 0.25,0.74 0.521,0.927 0.271,0.188 10 3 0.24,1.271 0.479,1.448 0.24,0.177 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the air fuel ratio sensor heater relay.


Hide 4.INSPECT NO. 1 INTEGRATION RELAY (MAIN)

a.

Check the EFI fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω


If the result is not as specified, replace the EFI fuse.



b.

Check the MAIN relay.

i.
A225101
2.354,1.563 2.719,1.781 0.365,0.219 1.208,1.563 1.573,1.781 0.365,0.219 0.323,1.563 0.688,1.781 0.365,0.219 2.49,1.583 2.719,1.76 0.229,0.177 10 false 1I 1.313,1.583 1.479,1.76 0.167,0.177 10 false 1J 0.406,1.583 0.625,1.76 0.219,0.177 10 false 1H 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a
*a Component without harness connected
(No. 1 Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-1 - 1J-4 Battery voltage not applied to terminals 1J-2 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1J-2 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 5.INSPECT NO. 1 INTEGRATION RELAY (EDU)

a.

for i-ART:

Check the EDU fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EDU fuse Always Below 1 Ω


If the result is not as specified, replace the EDU fuse.



b.
A225101
2.354,1.563 2.719,1.781 0.365,0.219 1.208,1.563 1.573,1.781 0.365,0.219 0.323,1.563 0.688,1.781 0.365,0.219 2.49,1.594 2.719,1.771 0.229,0.177 10 false 1I 1.313,1.583 1.479,1.76 0.167,0.177 10 false 1J 0.406,1.583 0.625,1.76 0.219,0.177 10 false 1H 0.115,0.083 0.344,0.313 0.229,0.229 10 false *a
*a Component without harness connected
(No. 1 Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1H-1 - 1J-8*1
1J-5 - 1J-8*2
Battery voltage not applied to terminals 1J-6 and 1J-7 10 kΩ or higher
Battery voltage applied to terminals 1J-6 and 1J-7 Below 1 Ω


*1: for i-ART

*2: except i-ART

If the result is not as specified, replace the No. 1 integration relay.