Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › MANIFOLD ABSOLUTE PRESSURE SENSOR(w/o Glow Plug Controller)
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052101 MANIFOLD ABSOLUTE PRESSURE SENSOR(w/o Glow Plug Controller) G

1KD-FTV ENGINE CONTROL  MANIFOLD ABSOLUTE PRESSURE SENSOR(w/o Glow Plug Controller)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

a.

Inspect the power source voltage.

i.

Disconnect the manifold absolute pressure sensor connector.


ii.
A301317
2.177,3.635 2.417,2.833 2.417,2.833 2.563,2.833 false 2.01,3.625 1.75,3.313 1.75,3.313 1.552,3.313 false 1.104,1.063 1,0.833 1,0.833 0.854,0.833 false 1.229,1.073 1.229,0.813 1.229,0.813 1.375,0.813 false 0.042,0.052 0.354,0.25 0.313,0.198 10 *A 0.042,2.375 0.354,2.573 0.313,0.198 10 *B 0.052,0.24 0.365,0.438 0.313,0.198 10 *a 0.063,2.531 0.375,2.729 0.313,0.198 10 *a 2.615,2.76 3.24,2.948 0.625,0.188 10 3 VC (+) 1.156,3.229 1.781,3.417 0.625,0.188 10 1 E (-) 0.448,0.75 1.073,0.938 0.625,0.188 10 1 E (-) 1.417,0.74 2.042,0.927 0.625,0.188 10 3 VC (+)
*A w/ EGR Cooler
*B w/o EGR Cooler
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Measure the voltage according to the value(s) in the table below.

If the result is not as specified, inspect the wire harness or ECM (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>TERMINALS OF ECM).

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3 VC (+) - 1 E (-) Ignition switch ON 4.75 to 5.25 V



iii.
A301621
0.625,0.615 1.01,0.885 0.385,0.271 1.26,0.604 1.646,0.875 0.385,0.271 1.417,3.406 1.417,3.76 true 2.823,3.417 2.823,3.771 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.677,0.688 1.01,0.854 0.333,0.167 10 false C22 1.333,0.677 1.667,0.844 0.333,0.167 10 false C23 1.292,3.792 1.677,3.99 0.385,0.198 10 false E2 (-) 2.615,3.792 3.125,3.969 0.51,0.177 10 false PIM (+)
*a Component with harness connected
(ECM)


Connect the manifold absolute pressure sensor connector.



b.

Check the power supply.

i.

Turn the ignition switch to ON.


ii.

Disconnect the vacuum hose from the manifold absolute pressure sensor.


iii.
A301318
0.875,3.26 1.24,3.26 false 1.323,0.396 1.833,0.396 false 0.073,0.073 0.385,0.271 0.313,0.198 10 false *A 0.094,2.417 0.406,2.615 0.313,0.198 10 false *B 1.281,3.177 1.594,3.375 0.313,0.198 10 false *1 1.125,0.333 1.438,0.531 0.313,0.198 10 false *1
*A w/ EGR Cooler
*B w/o EGR Cooler
*1 Vacuum Pump
V100135

Vacuum


Measure the voltage according to the value(s) in the table below.

Standard Voltage (w/ EGR Cooler):
Tester Connection Condition Specified Condition
C23-28 (PIM +) - C22-28 (E2 -) 13.3 kPa (100 mmHg, 3.94 in.Hg) 0.0 to 0.3 V
26.6 kPa (199 mmHg, 7.85 in.Hg) 0.1 to 0.4 V
40 kPa (300 mmHg, 11.81 in.Hg) 0.3 to 0.6 V


Standard Voltage (w/o EGR Cooler):
Tester Connection Condition Specified Condition
C23-28 (PIM +) - C22-28 (E2 -) 13.3 kPa (100 mmHg, 3.94 in.Hg) 0.1 to 0.4 V
26.6 kPa (199 mmHg, 7.85 in.Hg) 0.2 to 0.6 V
40 kPa (300 mmHg, 11.81 in.Hg) 0.4 to 0.8 V


HINT:

The values in the "Condition" column are gauge pressures.


If the result is not as specified, replace the manifold absolute pressure sensor.


iv.
A301319
1.146,3.5 1.198,3.156 1.198,3.156 1.344,3.156 false 1.271,0.813 1.448,0.813 1.448,0.813 1.646,0.573 false 0.969,0.74 1.427,0.938 0.458,0.198 10 false SST 1.375,3.083 1.833,3.281 0.458,0.198 10 false SST 0.052,0.063 0.365,0.219 0.313,0.156 10 false *A 0.073,2.396 0.385,2.552 0.313,0.156 10 false *B
*A w/ EGR Cooler
*B w/o EGR Cooler
V100135

Pressure


Using SST, measure the voltage according to the value(s) in the table below.

SST
09992-00242  

Standard Voltage (w/ EGR Cooler):
Tester Connection Condition Specified Condition
C23-28 (PIM +) - C22-28 (E2 -) 19.6 kPa (0.20 kgf/cm2, 2.84 psi) 0.05 to 0.3 V
39.2 kPa (0.40 kgf/cm2, 5.68 psi) 0.25 to 0.55 V
58.8 kPa (0.60 kgf/cm2, 8.53 psi) 0.45 to 0.75 V
78.5 kPa (0.80 kgf/cm2, 11.4 psi) 0.65 to 0.95 V
98.0 kPa (1.00 kgf/cm2, 14.2 psi) 0.9 to 1.2 V


Standard Voltage (w/o EGR Cooler):
Tester Connection Condition Specified Condition
C23-28 (PIM +) - C22-28 (E2 -) 19.6 kPa (0.20 kgf/cm2, 2.84 psi) 0.1 to 0.4 V
39.2 kPa (0.40 kgf/cm2, 5.68 psi) 0.4 to 0.7 V
58.8 kPa (0.60 kgf/cm2, 8.53 psi) 0.7 to 1.0 V
78.5 kPa (0.80 kgf/cm2, 11.4 psi) 1.0 to 1.3 V
98.0 kPa (1.00 kgf/cm2, 14.2 psi) 1.3 to 1.6 V


HINT:

The values in the "Condition" column are gauge pressures.


If the result is not as specified, replace the manifold absolute pressure sensor.