Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and is used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low EGR valve position sensor output voltage is below 0.1 V for more than 5 seconds (1 trip detection logic).
·

Open or short in EGR valve position sensor circuit

·

EGR valve position sensor

·

ECM


Comes on DTC stored
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High EGR valve position sensor output voltage is more than 4.9 V for higher than 5 seconds (1 trip detection logic).
·

Open or short in EGR valve position sensor circuit

·

EGR valve position sensor

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0405, P0406
DTC Detection Drive Pattern Ignition switch to ON for 5 seconds

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A154317
6.094,3.229 6.469,3.427 0.375,0.198 10 false ECM 0.448,3.198 0.76,3.396 0.313,0.198 10 false C56 1.677,1.365 1.938,1.563 0.26,0.198 10 false VC 5.354,1.292 5.573,1.479 0.219,0.188 10 false 18 5.323,1.469 5.615,1.656 0.292,0.188 10 false C22 5.375,1.844 5.594,2.031 0.219,0.188 10 false 33 5.323,2.031 5.615,2.219 0.292,0.188 10 false C23 5.365,2.385 5.583,2.573 0.219,0.188 10 false 28 5.333,2.573 5.625,2.76 0.292,0.188 10 false C22 1.979,1.552 2.146,1.75 0.167,0.198 10 false 1 1.979,2.135 2.115,2.302 0.135,0.167 10 false 3 1.979,2.667 2.125,2.854 0.146,0.188 10 false 2 1.5,1.948 1.906,2.146 0.406,0.198 10 false EGLS 1.688,2.49 1.948,2.688 0.26,0.198 10 false E2 5.656,1.375 5.917,1.573 0.26,0.198 10 false VC 5.646,1.938 6.094,2.135 0.448,0.198 10 false EGLS 5.656,2.479 5.917,2.677 0.26,0.198 10 false E2 0.448,3.365 2.219,3.563 1.771,0.198 10 false EGR Valve Position Sensor

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)
a.
A253299
0.583,0.99 1,1.25 0.417,0.26 1.438,1.188 1.219,1.719 true 1.771,1.198 2.167,1.719 true 0.667,1.042 0.938,1.229 0.271,0.188 10 false C56 0.208,0.125 0.427,0.292 0.219,0.167 10 false *a 1.104,1.74 1.344,1.896 0.24,0.156 10 false VC 2.135,1.708 2.354,1.865 0.219,0.156 10 false E2
*a Front view of wire harness connector
(to EGR Valve Position Sensor)


Disconnect the EGR valve position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C56-1 (VC) - C56-2 (E2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the electric vacuum regulating valve assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT EGR VALVE POSITION SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
2.INSPECT EGR VALVE POSITION SENSOR

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

NG

5.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the EGR valve position sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C56-1 (VC) - C22-18 (VC) Always Below 1 Ω
C56-3 (EGLS) - C23-33 (EGLS) Always Below 1 Ω
C56-2 (E2) - C22-28 (E2) Always Below 1 Ω
C56-1 (VC) or C22-18 (VC) - Body ground Always 10 kΩ or higher
C56-3 (EGLS) or C23-33 (EGLS) - Body ground Always 10 kΩ or higher



d.

Reconnect the electric vacuum regulating valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/o Glow Plug Controller)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END