The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0087 | Fuel Rail / System Pressure - Too Low | Fuel pressure sensor output voltage stays at fixed value for 90 seconds (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
Ran out of fuel ·
Fuel frozen ·
ECM |
Comes on | DTC stored |
| P0190 | Fuel Rail Pressure Sensor Circuit | Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored |
| P0192 | Fuel Rail Pressure Sensor Circuit Low Input | Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored |
| P0193 | Fuel Rail Pressure Sensor Circuit High Input | Fuel pressure sensor output voltage is 4.9 V or higher for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0087 | ·
Fuel Press ·
Target Common Rail Pressure |
| P0190 | |
| P0192 | |
| P0193 |
Check Fuel Press and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure. Under stable conditions, the difference between Fuel Press and Target Common Rail Pressure is 5000 kPa or less.
For more information on the fuel pressure sensor and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>SYSTEM DESCRIPTION).
If DTC P0087 is stored, the following symptoms may appear:
Black smoke
Poor drivability
Lack of power
Lack of power due to accelerator restriction performed by fail-safe function
If DTC P0190, P0192 and/or P0193 is stored, the following symptom may appear:
Lack of power due to accelerator restriction performed by fail-safe function
If DTC P0190, P0192 and/or P0193 is stored, "Fuel Press" always displays 0 kPa or 200000 kPa.
| DTC Detection Drive Pattern | After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
| DTC Detection Drive Pattern | Ignition switch to ON for 1 second |
Under normal conditions, the internal fuel pressure of the common rail usually fluctuates by 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 28000 to 40000 kPa (285 to 408 kgf/cm2, 4060 to 5801 psi) when idling, and it increases to approximately 30000 to 60000 kPa (306 to 612 kgf/cm2, 4351 to 8700 psi) when running the engine at 3000 rpm.
If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.
These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.
If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
If DTCs relating to different systems which share terminal E2 as their ground are stored, check this ground circuit first.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0190, P0192 or P0193 is output | A |
| P0087 is output | B |
A
B
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C16-5 (PR) - C22-26 (PCR1) | Always | Below 1 Ω |
| C16-2 (PR2) - C22-33 (PCR2) | Always | Below 1 Ω |
| C16-1 (VCS) - C23-2 (VCS) | Always | Below 1 Ω |
| C16-6 (VC) - C22-18 (VC) | Always | Below 1 Ω |
| C16-4 (E2) - C22-28 (E2) | Always | Below 1 Ω |
| C16-3 (E2S) - C23-1 (E2S) | Always | Below 1 Ω |
| C16-5 (PR) or C22-26 (PCR1) - Body ground | Always | 10 kΩ or higher |
| C16-2 (PR2) or C22-33 (PCR2) - Body ground | Always | 10 kΩ or higher |
| C16-1 (VCS) or C23-2 (VCS) - Body ground | Always | 10 kΩ or higher |
| C16-6 (VC) or C22-18 (VC) - Body ground | Always | 10 kΩ or higher |
| C16-4 (E2) or C22-28 (E2) - Body ground | Always | 10 kΩ or higher |
| C16-3 (E2S) or C23-1 (E2S) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Fuel Pressure Sensor) |
Disconnect the fuel pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C16-6 (VC) - C16-4 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| C16-1 (VCS) - C16-3 (E2S) | Ignition switch ON | 4.5 to 5.5 V |
Reconnect the fuel pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the common rail assembly.
Click hereEngine / Hybrid System>1KD-FTV FUEL>COMMON RAIL(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0087, P0190, P0192 or P0193 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0087, P0190, P0192 and/or P0193.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.
| Proceed to |
|---|
| NEXT |
NEXT