The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0180 | Fuel Temperature Sensor "A" Circuit | Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel temperature sensor circuit ·
Fuel temperature sensor (fuel supply pump assembly) ·
ECM |
Comes on | DTC stored |
| P0182 | Fuel Temperature Sensor "A" Circuit Low Input | Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Short in fuel temperature sensor circuit ·
Fuel temperature sensor (fuel supply pump assembly) ·
ECM |
Comes on | DTC stored |
| P0183 | Fuel Temperature Sensor "A" Circuit High Input | Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). | ·
Open in fuel temperature sensor circuit ·
Fuel temperature sensor (fuel supply pump assembly) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0180 | Fuel Temp |
| P0182 | |
| P0183 |
If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
Lack of power
When DTC P0180, P0182 and/or P0183 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC Detection Drive Pattern | Ignition switch to ON for 0.5 seconds |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
Same as the actual fuel temperature
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (Same as actual fuel temperature) | C |
If there is an open circuit, the tester indicates -40°C (-40°F).
If there is a short circuit, the tester indicates 140°C (284°F) or higher.
A
B
C
| *1 | Fuel Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Fuel Temperature Sensor) |
Disconnect the fuel temperature sensor connector.
Connect terminals 2 and 1 of the fuel temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
140°C (284°F) or higher
Reconnect the fuel temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C19-2 - C22-29 (THF) | Always | Below 1 Ω |
| C19-1 - C22-28 (E2) | Always | Below 1 Ω |
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Fuel Temperature Sensor |
| *2 | ECM |
Disconnect the fuel temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
-40°C (-40°F)
Reconnect the fuel temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform fuel supply pump initialization.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C19-2 or C22-29 (THF) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT