Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P1264  VN Turbo Controller Malfunction  


DESCRIPTION

The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, the turbo motor driver and ECM.

The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure, when the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.

The turbocharger actuator, which consists of the DC motor and the nozzle vane position sensor, is built on the turbocharger sub-assembly, and activates the nozzle vane. The nozzle vane position sensor detects the opening angle of the nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position signal from the nozzle vane position sensor. Based on these signals, the turbo motor driver operates the DC motor and adjusts the nozzle vane opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM

The ECM sends a target nozzle vane position signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.

A255070
0.052,0.74 1.438,0.927 1.385,0.188 10 false Ignition Switch Signal 0.448,1.104 1.427,1.313 0.979,0.208 10 false Engine Speed 0.104,1.479 1.396,1.646 1.292,0.167 10 false Accelerator Position 0.365,1.917 1.375,2.104 1.01,0.188 10 false Turbo Pressure 0.073,2.313 1.385,2.479 1.313,0.167 10 false Barometric Pressure 0.094,2.74 1.448,3.083 1.354,0.344 10 false Engine Coolant Temperature Sensor 1.906,3.115 2.271,3.302 0.365,0.188 10 false ECM 2.51,1.094 3.323,1.688 0.813,0.594 10 false Vane Nozzle Opening Angle Signal 2.573,2.552 3.385,2.938 0.813,0.385 10 false Motor Status Signal 3.344,3.135 4.552,3.313 1.208,0.177 10 false Turbo Motor Driver 5.76,1.563 6.438,1.75 0.677,0.188 10 false DC Motor 5.677,3.094 6.677,3.458 1,0.365 10 false Nozzle Vane Position Sensor 4.375,1.365 5.615,1.917 1.24,0.552 10 false DC Motor Activation Signal 4.594,2.052 5.417,2.229 0.823,0.177 10 false VCS, VNVC 4.594,2.333 5.406,2.51 0.813,0.177 10 false VTA1, VTA2 4.594,2.604 5.375,2.781 0.781,0.177 10 false E2S, VNE2 4.594,2.885 5.542,3.26 0.948,0.375 10 false Nozzle Vane Position Signal 4.385,0.604 4.656,0.771 0.271,0.167 10 false M+ 4.385,1.125 4.615,1.281 0.229,0.156 10 false M-

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1264 VN Turbo Controller Malfunction When communication error occurs between turbo motor and ECM
(1 trip detection logic)
·

Turbo motor driver

·

Open or short in turbo motor driver circuit

·

Turbo motor driver ground problem

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P1264
DTC Detection Drive Pattern Ignition switch to ON for 5 seconds

WIRING DIAGRAM

A255254
0.333,1.052 1.094,1.396 0.76,0.344 10 false from MAIN Relay 1.802,1.094 2,1.24 0.198,0.146 10 false +B 2.542,1.271 2.948,1.417 0.406,0.146 10 false VNTO 2.573,1.708 2.948,1.854 0.375,0.146 10 false VNTI 5.573,1.271 5.979,1.417 0.406,0.146 10 false VNTO 5.573,1.708 5.948,1.854 0.375,0.146 10 false VNTI 5.927,3.271 6.26,3.417 0.333,0.146 10 false C22 5.927,3.438 6.26,3.583 0.333,0.146 10 false ECM 5.313,1.188 5.5,1.333 0.188,0.146 10 false 10 5.313,1.625 5.49,1.76 0.177,0.135 10 false 17 3.063,1.156 3.167,1.313 0.104,0.156 10 false 7 3.063,1.604 3.156,1.75 0.094,0.146 10 false 2 1.677,3.26 1.979,3.448 0.302,0.188 10 false C39 1.688,3.396 2.875,3.542 1.188,0.146 10 false Turbo Motor Driver 2.615,2.604 2.948,2.76 0.333,0.156 10 false GND 1.573,0.99 1.677,1.135 0.104,0.146 10 false 3 3.063,2.5 3.156,2.646 0.094,0.146 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Excessive electrical noise, such as from wireless radios or electrical modifications, may cause a DTC output.



PROCEDURE

1.CHECK TURBO MOTOR DRIVER
A150167
0.229,1.49 0.677,1.74 0.448,0.25 1.406,2.063 0.646,2.552 true 2.188,2.083 2.521,2.594 true 0.406,0.26 0.604,0.427 0.198,0.167 10 false *a 0.448,2.521 0.729,2.708 0.281,0.188 10 false +B 0.313,1.521 0.594,1.708 0.281,0.188 10 false C39 2.479,2.656 2.833,2.833 0.354,0.177 10 false GND
*a Front view of wire harness connector
(to Turbo Motor Driver)


a.

Disconnect the turbo motor driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C39-3 (+B) - C39-4 (GND) Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-4 (GND) - Body ground Always Below 1 Ω



e.

Reconnect the turbo motor driver connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the turbo motor driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-10 (VNTO) - C39-7 (VNTO) Always Below 1 Ω
C22-17 (VNTI) - C39-2 (VNTI) Always Below 1 Ω
C22-10 (VNTO) or C39-7 (VNTO) - Body ground Always 10 kΩ or higher
C22-17 (VNTI) or C39-2 (VNTI) - Body ground Always 10 kΩ or higher



d.

Reconnect the turbo motor driver connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VNTO VOLTAGE)

NG

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.INSPECT ECM (VNTO VOLTAGE)
a.
A303435
0.594,0.375 0.99,0.615 0.396,0.24 1.26,0.375 1.656,0.615 0.396,0.24 0.354,1.583 0.906,0.917 true 1.448,1.594 1.177,0.833 true 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 0.667,0.417 0.979,0.615 0.313,0.198 10 false C22 1.333,0.417 1.646,0.615 0.313,0.198 10 false C23 0.229,1.625 1.01,1.865 0.781,0.24 10 false 10 (VNTO) 1.313,1.635 2.094,1.875 0.781,0.24 10 false 7 (E1) 2.781,2.646 3.375,2.865 0.594,0.219 10 false 5 V/DIV. 0.281,3.26 0.875,3.479 0.594,0.219 10 false VNTO 1.333,4.385 2.365,4.625 1.031,0.24 10 false 20 msec./DIV.
*a Component with harness connected
(ECM)


While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

Standard Voltage:
Tester Connection Condition Specified Condition
C22-10 (VNTO) - C23-7 (E1) Idling Correct waveform is as shown



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (VNTI VOLTAGE)

NG

6.REPLACE ECM
4.INSPECT ECM (VNTI VOLTAGE)
a.
A303436
0.604,0.333 0.99,0.594 0.385,0.26 1.25,0.333 1.635,0.594 0.385,0.26 0.375,1.604 0.531,0.927 true 1.354,1.625 1.198,0.844 true 0.135,0.094 0.375,0.313 0.24,0.219 10 false *a 0.677,0.375 1.021,0.594 0.344,0.219 10 false C22 1.333,0.375 1.635,0.583 0.302,0.208 10 false C23 0.271,1.646 0.958,1.906 0.688,0.26 10 false 17 (VNTI) 1.271,1.646 1.958,1.906 0.688,0.26 10 false 7 (E1) 0.323,3.26 0.698,3.469 0.375,0.208 10 false VNTI 2.802,2.667 3.365,2.885 0.563,0.219 10 false 2 V/DIV. 1.375,4.396 2.323,4.615 0.948,0.219 10 false 20 msec./DIV.
*a Component with harness connected
(ECM)


While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

Standard Voltage:
Tester Connection Condition Specified Condition
C22-17 (VNTI) - C23-7 (E1) Idling Correct waveform is as shown



Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS

NG

7.REPLACE TURBO MOTOR DRIVER
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE TURBO MOTOR DRIVER

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.


f.

Turn the ignition switch to ON and wait for 10 seconds or more.


g.

Start the engine.


h.

Drive the vehicle with a city driving pattern at least 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END