The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0488 | Exhaust Gas Recirculation Throttle Position Control Range / Performance | The throttle motor activation duty is more than a specified value for 30 seconds (1 trip detection logic). | ·
Throttle valve stuck ·
Throttle valve does not move smoothly ·
Open or short in throttle control motor circuit ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0488 | Actual Throttle Position |
| Condition | Throttle Valve Position |
|---|---|
| Moment when accelerator pedal is depressed further or released at 3000 rpm | Throttle valve opening angle varies smoothly |
| DTC Detection Drive Pattern | Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. |
The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Although the DTC titles say exhaust gas recirculation throttle position control Range / Performance, these DTCs relate to the throttle valve
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Throttle Control Motor) |
Disconnect the throttle control motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C15-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the throttle control motor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle control motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C15-3 (RSC) - Body ground | Always | Below 1 Ω |
Reconnect the throttle control motor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C15-1 (RSO) - C23-4 (LUSL) | Always | Below 1 Ω |
| C15-1 (RSO) or C23-4 (LUSL) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle control motor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0488 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0488.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.
| Proceed to |
|---|
| NEXT |
NEXT