Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) D

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  SYSTEM DESCRIPTION  


ENGINE CONTROL SYSTEM


A251330
6.083,1.854 6.396,1.417 true 6.115,2.021 6.594,1.906 true 5.698,2.49 5.854,2.427 false 4.729,2.49 4.615,2.375 false 5.438,4.354 5.583,4.177 false 5.792,4.573 5.948,4.417 false 5.729,5.125 5.906,4.948 false 3.427,4.823 3.281,4.396 true 3.438,4.896 3.302,5.042 false 3.448,5.927 3.24,5.635 false 4.896,6.083 4.656,5.74 true 5.021,6.458 5.458,6.896 true 4.271,7.5 4,7.615 false 4.677,7.948 4.271,7.948 true 2.083,2.208 2.292,2.375 0.208,0.167 10 false *1 2.073,2.635 2.281,2.802 0.208,0.167 10 false *2 1.229,1.406 1.438,1.573 0.208,0.167 10 false *3 0.344,1.917 0.552,2.083 0.208,0.167 10 false *4 0.344,2.135 0.552,2.302 0.208,0.167 10 false *5 0.344,2.365 0.552,2.531 0.208,0.167 10 false *6 0.344,2.604 0.552,2.771 0.208,0.167 10 false *7 0.344,2.854 0.552,3.021 0.208,0.167 10 false *8 0.344,3.083 0.552,3.25 0.208,0.167 10 false *9 0.302,3.302 0.542,3.469 0.24,0.167 10 false *10 5.323,0.552 5.604,0.74 0.281,0.188 10 false *11 6.406,1.302 6.688,1.49 0.281,0.188 10 false *12 6.635,1.854 6.917,2.042 0.281,0.188 10 false *13 5.365,1.51 5.646,1.698 0.281,0.188 10 false *14 3.677,1.5 3.958,1.688 0.281,0.188 10 false *15 4.375,2.302 4.656,2.49 0.281,0.188 10 false *16 5.896,2.354 6.177,2.542 0.281,0.188 10 false *17 5.073,2.448 5.354,2.635 0.281,0.188 10 false *18 4.229,3.156 4.51,3.344 0.281,0.188 10 false *19 5.604,4.073 5.885,4.26 0.281,0.188 10 false *20 5.99,4.344 6.271,4.531 0.281,0.188 10 false *21 5.146,4.708 5.427,4.896 0.281,0.188 10 false *22 3.073,4.979 3.354,5.167 0.281,0.188 10 false *24 3.219,4.229 3.5,4.417 0.281,0.188 10 false *23 5.927,4.865 6.208,5.052 0.281,0.188 10 false *25 4.438,5.625 4.719,5.813 0.281,0.188 10 false *26 3.01,5.531 3.292,5.719 0.281,0.188 10 false *27 3.198,6.604 3.479,6.792 0.281,0.188 10 false *28 2.771,6.177 3.052,6.365 0.281,0.188 10 false *29 6.448,6 6.729,6.188 0.281,0.188 10 false *30 6.063,5.667 6.344,5.854 0.281,0.188 10 false *31 5.667,6.542 5.948,6.729 0.281,0.188 10 false *32 6.396,6.552 6.677,6.74 0.281,0.188 10 false *33 4.406,6.625 4.688,6.813 0.281,0.188 10 false *34 3.771,7.552 4.052,7.74 0.281,0.188 10 false *35 4.052,7.875 4.333,8.063 0.281,0.188 10 false *36 5.51,6.833 5.792,7.021 0.281,0.188 10 false *37 6.302,7.51 6.583,7.698 0.281,0.188 10 false *38 3.76,3.01 4.042,3.198 0.281,0.188 10 false *39
*1 ECM *2 Atmospheric Pressure Sensor
*3 Accelerator Pedal Position Sensor *4 Ignition Switch Signal
*5 Starter Signal *6 Vehicle Speed Signal
*7 DLC3 *8 Battery Voltage
*9 Stop Light Switch *10 Other Signal
*11 Fuel Tank *12 Suction Control Valve
*13 Fuel Temperature Sensor *14 Fuel Supply Pump Assembly
*15 Generator *16 Fuel Pressure Sensor
*17 Pressure Discharge Valve *18 Common Rail Assembly
*19 Injector Driver *20 Intake Air Temperature Sensor (Turbo)
*21 Diesel Throttle Body Assembly *22 Intercooler
*23 Mass Air Flow Meter *24 Intake Air Temperature Sensor (Built Into Mass Air Flow Meter)
*25 Manifold Absolute Pressure Sensor *26 Injector Assembly
*27 Turbocharger Sub-assembly *28 DC motor, Nozzle Vane Position Sensor
*29 Turbo Motor Driver *30 Electric Vacuum Regulating Valve Assembly (w/ EGR System)
*31 Vacuum Switching Valve (for EGR Cut) (w/ EGR System) *32 Vacuum Switching Valve (for Swirl Control Valve)
*33 Vacuum Pump *34 Engine Coolant Temperature Sensor
*35 Camshaft Position Sensor *36 Crankshaft Position Sensor
*37 Glow Plug *38 Glow Plug Relay (GLOW)
*39 EDU Relay - -



COMMON RAIL SYSTEM DESCRIPTION


a.

Common rail system:

The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power, while suppressing engine vibration and noise.

This system stores fuel in the common rail, which is pressurized and supplied with fuel by the supply pump. By storing fuel at high pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.

The ECM, using the injector driver, provides an electric current to the solenoid valve in each injector assembly to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the supply pump to supply the fuel necessary to obtain the target fuel pressure.

In addition, this system uses a solenoid valve inside each injector assembly to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.

The common rail system allows a two-stage fuel injection process. In order to soften combustion shock, this system performs "pilot injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.

A227741
1.75,1.313 1.729,0.917 1.729,0.917 1.583,0.917 false 1.75,2.198 2.063,1.833 2.063,1.833 1.865,1.833 false 0.969,2.615 0.875,3 false 2.24,1.292 2.354,1.063 2.354,1.063 2.458,1.063 false 5.031,1.313 4.573,0.771 4.573,0.771 4.354,0.771 false 1.677,3.99 2.219,4.365 false 4.01,4.031 3.854,4.479 false 4.854,4.844 5.302,5.021 0.448,0.177 10 false ECM 6.271,4.833 6.771,5.042 0.5,0.208 10 false Sensor 0.073,0.073 3.156,0.313 3.083,0.24 10 false Common Rail System Diagram (Fuel System) 0.167,0.833 1.583,1.021 1.417,0.188 10 false Fuel Pressure Sensor 2.51,0.99 4.083,1.188 1.573,0.198 10 false Common Rail Assembly 2.75,0.688 4.417,0.865 1.667,0.177 10 false Pressure Discharge Valve 4.677,0.479 6.063,0.656 1.385,0.177 10 false : High-pressure Area 0.292,1.75 1.917,1.938 1.625,0.188 10 false Fuel Temperature Sensor 0.156,3.021 1.229,3.375 1.073,0.354 10 false Fuel Supply Pump Assembly 0.469,3.844 1.677,4.271 1.208,0.427 10 false Fuel Filter Element Sub-assembly 1.229,4.677 1.885,4.844 0.656,0.167 10 false Fuel Tank 4.063,3.896 4.958,4.073 0.896,0.177 10 false Injector Driver 5.583,3.365 6.75,3.552 1.167,0.188 10 false Injector Assembly


b.

Common rail system components:

Component Description
Common rail assembly Stores high-pressure fuel supplied by fuel supply pump assembly
Fuel supply pump assembly Operated by crankshaft.
Supplies high-pressure fuel to common rail assembly.
Injector assembly Injects fuel into combustion chamber based on signals from ECM
Fuel pressure sensor Monitors internal fuel pressure of common rail assembly and sends signals to ECM
Pressure discharge valve Opens based on signals from ECM when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high
Suction control valve Adjusts fuel volume supplied to common rail and regulates internal fuel pressure based on signals from ECM
Check valve Maintains pressure of fuel that discharges from injector


c.

Diagnostic Trouble Codes (DTC) table for the common rail system:

HINT:

This table indicates typical DTC combinations for each malfunction.


Trouble Area Malfunction DTC No.
Injector assembly Open or short in injector circuit P0200, P0093*
Stuck open P0093
Stuck closed -
Fuel pressure sensor Open or short in fuel pressure sensor circuit or pressure sensor output fixed P0087, P0190, P0191, P0192, P0193
Pressure discharge valve Open or short in pressure discharge valve circuit P1271, P1272, P0088*, P0093*, P1229*
Stuck open P0093
Stuck closed P1272, P0088*
Suction control valve Open or short in suction control valve circuit P0627, P1229, P0088*
Stuck open P1229, P0088*
Stuck closed -
Injector driver Faulty injector driver P0093*, P0200*, P1271*, P1272*
Common rail system (Fuel system) Fuel leaks in high-pressure area P0093

*: There may be no DTCs stored depending on the condition of the malfunction.


d.

Diagnostic trouble code description for the common rail system:

DTC No. Description
P0087 Fuel pressure sensor output does not change
P0088 Internal fuel pressure too high (200 MPa [2,039 kgf/cm2, 29,007 psi] or higher)
P0093 Fuel leaks in high-pressure areas
P0190 Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
P0191 Fuel pressure sensor out of range (Low output)
P0192 Open or short in fuel pressure sensor circuit (output voltage is too low)
P0193 Open or short in fuel pressure sensor circuit (output voltage is too high)
P0200 Open or short in injector driver or injector circuit
P0627 Open or short in suction control valve circuit
P1229 Fuel overfeed
P1271 Open or short in pressure discharge valve circuit
P1272 Closed malfunction of the pressure discharge valve



INJECTION CONTROL SYSTEM DESCRIPTION


The ECM controls the fuel injection system through the injector driver, injector assemblies and fuel supply pump assembly.

The ECM determines the injection volume and injection timing based on signals from the accelerator position sensor, crankshaft position sensor and camshaft position sensor. The injector driver controls the injector assemblies based on signals from the ECM. The injector driver also controls the suction control valve installed on the supply pump to help regulate fuel pressure.

The feed pump is used to pump fuel from the fuel tank to the supply pump.

A148213
5.927,5.125 6.125,5.125 false 5.917,3.75 6.271,4.021 false 5.927,3.229 6.292,3.229 false 5.99,2.75 6.385,2.677 false 5.896,2.302 6.375,1.802 false 5.948,1.958 6.25,1.125 6.25,1.125 6.365,1.125 false 5.646,2.969 5.208,2.656 false 3.854,4.135 3.656,3.333 3.656,3.333 3.552,3.333 false 2.76,4.469 2.677,3.365 2.677,3.365 2.594,3.365 false 2.302,4.75 2.479,5.219 false 3.74,4.625 2.74,5.844 false 4.375,5.552 4.448,5.885 false 3.583,2.208 3.531,1.75 3.531,1.75 3.438,1.75 false 4.302,0.969 4.042,1.354 false 0.104,1.125 1.281,1.49 1.177,0.365 10 false Accelerator Pedal Position Sensor 0.115,0.063 1.74,0.313 1.625,0.25 10 false Injection Control Diagram 5.427,5.552 6.604,5.75 1.177,0.198 10 false Injector Assembly 6.198,5.052 6.708,5.417 0.51,0.365 10 false Nozzle Needle 6.313,3.958 6.802,4.156 0.49,0.198 10 false Piston 6.354,3.177 6.948,3.542 0.594,0.365 9 false Control Chamber 6.458,2.583 6.917,2.781 0.458,0.198 10 false Orifice 4.781,2.51 5.26,2.688 0.479,0.177 10 false Orifice 6.427,1.729 6.854,1.927 0.427,0.198 10 false TWV 6.396,1.031 6.99,1.396 0.594,0.365 10 false Solenoid Valve 4.323,0.833 5.24,1.031 0.917,0.198 10 false Injector Driver 2.094,2.302 3.625,2.51 1.531,0.208 10 false Common Rail Assembly 2.083,1.656 3.521,1.854 1.438,0.198 10 false Fuel Pressure Sensor 4.167,5.906 5.073,6.115 0.906,0.208 10 false Check Valve 3.063,3.24 3.615,3.448 0.552,0.208 10 false Plunger 2.24,5.885 3.198,6.083 0.958,0.198 10 false Eccentric Cam 2.281,5.24 3.042,5.458 0.76,0.219 10 false Feed Pump 2.135,3.115 2.667,3.625 0.531,0.51 10 false Suction Control Valve 0.104,4.292 1.094,4.49 0.99,0.198 10 false Other Sensors 0.854,5.813 1.604,6.01 0.75,0.198 10 false Fuel Tank 0.104,3.531 1.375,3.927 1.271,0.396 10 false Crankshaft Position Sensor (NE Signal) 0.104,2.302 1.292,2.667 1.188,0.365 10 false Camshaft Position Sensor 1.563,2.479 1.927,2.667 0.365,0.188 10 false ECM


SUPPLY PUMP OPERATION SYSTEM DESCRIPTION


The rotation of the eccentric cam in the supply pump causes the ring cam in the supply pump to push plunger A upward as illustrated below. The spring force pulls plunger B (located opposite to plunger A) upward. As a result, plunger B draws the fuel in and plunger A pumps fuel out at the same time.

A148214
0.469,2.104 0.469,1.135 0.469,1.135 0.583,1.135 false 1.531,1.021 2.354,0.5 2.354,0.5 2.521,0.5 false 2.354,0.5 2.198,1.021 false 1.854,1.448 3.021,0.865 false 1.938,1.917 3,1.406 false 2.083,2.208 2.969,2.719 false 1.917,2.49 2.948,3.083 false 0.99,2.781 0.99,3.375 0.99,3.375 0.844,3.375 false 0.094,0.073 2.448,0.281 2.354,0.208 10 false Supply Pump Operation Diagram 0.625,0.969 1.146,1.5 0.521,0.531 10 false Suction Control Valve 2.583,0.427 3.542,0.635 0.958,0.208 10 false Check Valve 3.073,0.781 3.865,1 0.792,0.219 10 false Plunger A 3.052,1.333 4.167,1.542 1.115,0.208 10 false Eccentric Cam 2.896,1.729 4.573,1.938 1.677,0.208 10 false to Common Rail Assembly 3,2.677 3.698,2.875 0.698,0.198 10 false Ring Cam 3.031,3.052 3.688,3.26 0.656,0.208 10 false Plunger B 1.104,3.135 2.865,3.344 1.76,0.208 10 false Plunger A: Pumping End 1.104,3.448 2.969,3.656 1.865,0.208 10 false Plunger B: Suction End 0.125,3.302 0.896,3.75 0.771,0.448 10 false from Feed Pump 4.958,3.177 6.771,3.385 1.813,0.208 10 false Plunger A: Suction Start 4.958,3.458 6.781,3.677 1.823,0.219 10 false Plunger B: Pumping Start 4.958,6.688 6.625,6.896 1.667,0.208 10 false Plunger A: Suction End 4.958,7.083 6.771,7.302 1.813,0.219 10 false Plunger B: Pumping End 1.052,6.698 3.115,6.99 2.063,0.292 10 false Plunger A: Pumping Start 1.052,7.083 3.125,7.323 2.073,0.24 10 false Plunger B: Suction Start


SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION


HINT:

The ECM controls the suction control valve operation to regulate the fuel volume that is produced by the supply pump for the common rail. This control is performed to regulate the internal fuel pressure of the common rail so that it reaches the targeted injection pressure.


a.

When the suction control valve opening is small:

i.

When the opening of the suction control valve is small, the volume of supplied fuel is small.


ii.

The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.


iii.

Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).

A208439
1.542,1.781 0.792,1.427 false 1.594,1.906 1.167,2.052 false 2.5,1.5 1.927,1.5 1.927,1.5 1.927,1.781 false 2.448,1.51 2.448,1.781 false 0.063,0.052 1.417,0.615 1.354,0.563 10 false Suction Control Valve Operation with Small Opening 1.531,0.052 2.688,0.552 1.156,0.5 10 false Plunger Top Dead Center 0.292,1.354 0.802,1.948 0.51,0.594 10 false Suction Control Valve 0.917,2.063 1.51,2.469 0.594,0.406 10 false Small Opening 2.542,1.427 3.375,1.604 0.833,0.177 10 false Check Valve 0.771,0.865 1.615,1.104 0.844,0.24 10 false Cam Stroke 4.26,0.052 5.208,0.479 0.948,0.427 10 false Pump Output Starting Point 5.469,0.219 6.979,0.49 1.51,0.271 10 false : Fuel Pumping Volume 2.823,0.052 4.198,0.448 1.375,0.396 10 false Plunger Bottom Dead Center 1.99,1.26 2.188,1.448 0.198,0.188 10 true (1) 2.104,2.552 2.302,2.74 0.198,0.188 10 false (1) 3.313,1.302 3.51,1.49 0.198,0.188 10 false (2) 3.521,2.594 3.719,2.781 0.198,0.188 10 false (2) 4.156,1.313 4.354,1.5 0.198,0.188 10 false (3) 4.813,2.573 5.01,2.76 0.198,0.188 10 false (3) 4.813,1.469 5.031,1.656 0.219,0.188 10 false (A) 5.271,1.469 5.49,1.656 0.219,0.188 10 false (B)



b.

When the suction control valve opening is large:

i.

When the opening of the suction control valve is large, the volume of supplied fuel is increased.


ii.

If the plunger stroke is full, the suction volume becomes large because of the wide path.


iii.

Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).

A208440
1.604,1.625 0.823,1.417 false 1.573,1.74 1.156,2.052 false 0.094,0.094 1.448,0.646 1.354,0.552 10 false Suction Control Valve Operation at Large Opening 0.313,1.313 0.813,1.875 0.5,0.563 10 false Suction Control Valve 0.948,2.052 1.521,2.51 0.573,0.458 10 false Large Opening 0.813,0.917 1.688,1.198 0.875,0.281 10 false Cam Stroke 3.021,0.063 4.01,0.563 0.99,0.5 10 false Pump Output Starting Point 5.49,0.219 7,0.458 1.51,0.24 10 false : Fuel Pumping Volume 1.99,1.375 2.188,1.563 0.198,0.188 10 false (1) 2.146,2.448 2.344,2.635 0.198,0.188 10 false (1) 3.313,1.354 3.51,1.563 0.198,0.208 10 false (2) 3.792,2.5 3.99,2.688 0.198,0.188 10 false (2) 3.563,1.354 3.75,1.573 0.188,0.219 10 false (3) 5.188,2.49 5.385,2.677 0.198,0.188 10 false (3) 5.177,1.438 5.396,1.625 0.219,0.188 10 false (A) 5.604,1.438 5.823,1.625 0.219,0.188 10 false (B)