Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) U

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Start the engine.


f.

Turn the intelligent tester on.


g.
A253563
1.094,2.281 1.49,2.604 1.49,2.604 2.156,2.604 true 1.156,1.031 1.688,0.531 1.688,0.531 2.073,0.531 true 0.135,0.052 0.948,0.271 0.813,0.219 10 false Example: 2.135,0.458 3.313,0.698 1.177,0.24 10 false Pull Down Menu 2.208,2.521 3.073,3.042 0.865,0.521 10 false Measurement Group

Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:
·

To display the list box, press the pull down menu button next to "Primary". Then select a measurement group.

·

When you select a measurement group, the ECU data belonging to that group is displayed.


·

Measurement Group List / Description

·

All Data / All data

·

Primary / -

·

Engine Control / Engine control system related data

·

Vehicle Information / Vehicle information

·

Monitor Status / Monitor status related data

·

AF Control System / Not Applicable

·

Catalytic Converter / Not Applicable

·

Evaporative / Not Applicable

·

A/T / Automatic transmission system related data

·

ETCS / Not Applicable

·

Misfire / Not Applicable

·

Compression / Data used during "Check the Cylinder Compression" Active Test

·

HC Absorber System / Not Applicable

·

Diesel Driving / Driving condition data

·

Diesel Injection / Fuel system related data

·

Diesel EGR / EGR system related data

·

Diesel Throttle / Diesel throttle system related data

·

Diesel VN Turbo / VN turbo related data

·

Diesel Exhaust / Exhaust system related data

·

Diesel Starting / "Difficult to start" related data

·

Diesel Rough / "Rough idle" related data

·

Diesel Power / "Lack of power" related data





h.

Check the values by referring to the table below.

HINT:

"Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.




Engine Control


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Sensor output (speed sensor) Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed Cause of Out of Range:
·

Speed sensor

·

Speed sensor circuit


Engine Speed Engine speed Sensor output (crankshaft position sensor) Min.: 0 rpm, Max.: 6000 rpm
·

50 to 400 rpm: Cranking

·

700 to 800 rpm: Idling with warm engine


When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.
Cause of Out of Range:
·

Crankshaft position sensor

·

Crankshaft position sensor circuit


Calculate Load Load calculated by ECM Calculated by ECM Min.: 0%, Max.: 100%
·

Idling: 11.4 to 16.4%

·

Running without load (2500 rpm): 13.1 to 18.9%


Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100.
Cause of Out of Range:
Malfunction in which turbo pressure or Mass Air Flow decreases
MAF Air flow rate from mass air flow meter Sensor output (mass air flow meter) Min.: 0 gm/s, Max.: 400 gm/s
for w/ EGR system
·

5 to 12 gm/s: Idling

·

23 to 31 gm/s: Running without load (2,000 rpm)


for w/o EGR system
·

13 to 21 gm/s: Idling

·

52 to 60 gm/s: Running without load (2,000 rpm)


HINT:

Depends on EGR rate


·

Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.

·

If the value is always approximately 0 gm/s:

·

Mass air flow meter power source circuit is open.

·

VG circuit is open or shorted.


·

If the value is always 167.5 gm/s or more:

·

EVG circuit is open.



Cause of Out of Range:
·

Mass air flow meter

·

Mass air flow meter circuit

·

Intake related clog or leak

·

Exhaust related clog

·

Turbocharger sub-assembly

·

Leak or clog in passages for turbocharger

·

Malfunction in which EGR valve does not close


Symptoms when out of range:
Rough idling
Atmosphere Pressure Atmospheric pressure value Sensor output (atmospheric pressure sensor [built into ECM]) Min.: 0 kPa, Max.: 255 kPa Actual atmospheric pressure
·

With the ignition switch to ON, when the difference between the atmospheric pressure sensor and intake manifold absolute pressure is 10 kPa or more, there is a malfunction in one of the sensors.

·

With the ignition switch to ON, when the atmospheric pressure is 0 kPa or 140 kPa, there is a malfunction in the sensor circuit.

·

Standard atmospheric pressure: 101 kPa.

·

For every 100 m increase in elevation, pressure drops by 1 kPa.

This varies by weather (high atmospheric pressure, low atmospheric pressure).


Cause of Out of Range:
Atmospheric pressure sensor itself has failed (atmospheric pressure sensor is inside the ECM)
MAP Absolute pressure inside intake manifold Sensor output (manifold absolute pressure sensor) Min.: 0 kPa, Max.: 255 kPa
for w/ EGR system
·

90 to 105 kPa: Idling

·

100 to 125 kPa: Engine running at 3000 rpm


for w/o EGR system
·

85 to 100 kPa: Idling

·

110 to 135 kPa: Engine running at 3000 rpm


·

When the ignition switch is on or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa).

Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure.

·

Inspect while comparing with "Target Booster Pressure".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.


Cause of Out of Range:
·

Manifold absolute pressure sensor

·

Intake related clog or leak

·

Exhaust related clog

·

Turbocharger sub-assembly

·

Leak or clog in passages for turbocharger

·

EGR valve stuck open

·

Exhaust leak

·

Throttle valve stuck closed


Symptoms when out of range:
Lack of power
Coolant Temp Engine coolant temperature Sensor output (engine coolant temperature sensor) Min.: -40°C, Max.: 140°C After warming up engine: 70 to 90°C (158 to 194°F)
·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

·

After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal.


Cause of Out of Range:
·

Engine coolant temperature sensor

·

Thermostat


Symptoms when out of range:
Difficulty starting when engine is cold, rough idle, black smoke, lack of power
Intake Air Intake air temperature Sensor output (intake air temperature sensor [built into mass air flow meter]) Min.: -40°C, Max.: 140°C Equivalent to temperature at location of mass air flow meter
·

After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal.

·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.


Cause of Out of Range:
Intake air temperature sensor
Intake Air Temp (Turbo) Intake air temperature after intercooler Sensor output (intake air temperature sensor after intercooler) Min.: -40°C, Max.: 190°C 70°C (158°F) or less
·

This is the intake air temperature at the intake manifold (after the intercooler).

·

During fail-safe operation, the value is set to 165°C (329°F). As the value is set to a high temperature, the turbo pressure may be suppressed and there may be a lack of power.


Cause of Out of Range:
Decreased cooling efficiency of intercooler (contamination, clogging)
Engine Run Time Engine run time Result of ECU calculations (using the engine speed) Min.: 0 sec., Max.: 65535 sec. Time after the ignition switch turned on Time passed since the ignition switch was turned on.
Initial Engine Coolant Temp Initial engine coolant temperature Sensor output when engine started Min.: -40°C, Max.: 120°C Engine coolant temperature when engine started For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine.
Initial Intake Air Temp Initial intake air temperature Sensor output when engine started Min.: -40°C, Max.: 120°C Intake air temperature when engine started -
Battery Voltage Battery voltage - Min.: 0 V, Max.: 15 V 11 to 14 V If 11 V or less, characteristics of some electrical components change.
Symptoms when out of range:
If 5 V or less, starting becomes difficult
Alternate Duty Ratio Alternator generation duty ratio Duty value from ALT terminal Min.: 0%, Max.: 100%
·

No electrical load at idling:

20 to 60%

·

High electrical load at idling:

100%


·

This is outputs the alternator generation duty and is used to determine the electrical load.

·

Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction.

·

Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device like the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, like battery deterioration.


Cause of Out of Range:
·

Battery deterioration

·

Alternator malfunction

·

Electric load, lights, etc.


Pre Glow Pre-glow operation Result of ECU calculations ON or OFF - This is the ECM command.
After Glow After-glow operation Result of ECU calculations ON or OFF - This is the ECM command.
Accel Position Accelerator position status
·

Accelerator pedal position sensor opening position

·

ETC requested opening position

·

Cruise requested opening position

·

VSC requested opening position


Min.: 0%, Max.: 100%
·

Accelerator pedal released:

0%

·

Accelerator pedal fully depressed:

100%


·

"Accel Position" is the accelerator opening amount (%) for engine control use.

·

When the accelerator pedal position sensor output itself (Accelerator Position 1, Accelerator Position 2) is in the normal voltage range, another actuator malfunction has caused the fail-safe function to restrict the accelerator.

·

Without cruise, ETC or VSC requests, and without accelerator restriction by the fail-safe function, this is adjusted in proportion to the amount the accelerator pedal is depressed by the driver.

·

Accelerator pedal released: 0%

·

Accelerator pedal fully depressed: 100%


HINT:

Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".


Accel Sens. No.1 Volt % Accelerator position No. 1 Sensor output (Accelerator pedal position sensor) Min.: 0%, Max.: 100%
·

Accelerator pedal released:

10 to 22%

·

Accelerator pedal fully depressed:

52 to 90%


Read value with ignition switch to ON (do not start engine)
HINT:

Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".


Accel Sens. No.2 Volt % Accelerator position No. 2 Sensor output (Accelerator pedal position sensor) Min.: 0%, Max.: 100%
·

Accelerator pedal released:

24 to 40%

·

Accelerator pedal fully depressed:

68 to 99%


Read value with ignition switch to ON (do not start engine)
HINT:

Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".


Starter Signal Starter signal - ON or OFF ON: Cranking Ignition switch (STA) output:
·

ON: Starter is operating.

·

OFF: Starter is not operating.


Cause of Out of Range:
·

OFF malfunction (ignition switch [STA] is ON but the signal is OFF and the starter is operating): Wire harness is open or shorted to ground

·

ON malfunction (ignition switch [STA] is off but the signal is ON and the starter is not operating): Wire harness is shorted to +B

·

Operation malfunction: ignition switch malfunction, starter relay malfunction, starter malfunction, battery or battery cable is defective, or wire harness is open or shorted


Symptoms when out of range:
·

Ignition switch is on but the starter does not operate: Starting is not possible

·

Ignition switch is off but the starter continues to operate: STA signal malfunction (P0617) is stored


Neutral Position SW Signal Neutral position switch status Switch output (neutral position switch) ON or OFF ON: Shift lever in neutral -
Clutch Switch Clutch switch Switch output (clutch switch) ON or OFF ON: Clutch pedal depressed When this item displays "OFF" with the clutch pedal depressed, the shock when accelerating and decelerating the vehicle becomes larger and pilot quality learning cannot be performed.
Symptoms when out of range:
The cruise control, pilot quantity learning, etc. may not function properly or may not function at all.
Stop Light Switch Stop light switch Switch output (stop light switch) ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


Stop light switch (STP) operation condition:
·

ON: Light is on (Brake pedal is depressed).

·

OFF: Light is off (Brake pedal is released).


Cause of Out of Range:
·

OFF malfunction: Wire harness (stop light switch to ECM, stop light switch to +B) open or shorted to ground

·

ON malfunction: Wire harness (stop light switch to ECM) shorted to +B

·

Stop light switch


Symptoms when out of range:
Stop light switch malfunction DTC P0504 is stored
A/C Signal A/C (Air Conditioner) signal A/C operation signal output from A/C amplifier
·

ON: Operating

·

OFF: Not operating


ON or OFF ON: A/C on Cause of Out of Range:
·

A/C switch

·

A/C amplifier

·

A/C system malfunction, wire harness between A/C amplifier and ECU open or shorted


Symptoms when out of range:
OFF malfunction (OFF even when A/C switch is turned on):
·

Engine speed decreases temporarily when the A/C is operating.


Immobiliser Communication Immobiliser communication - ON or OFF
·

ON: Normal

·

OFF: Engine cannot be started due to immobiliser communication malfunction


Cause of Out of Range:
·

Use of a non-registered key

·

Key battery is fully depleted


Check Mode Check mode - ON or OFF ON: Check mode on Check Mode: The mode in which certain DTCs can be detected more easily and with higher sensitivity.
SPD Test Result Check mode result for vehicle speed sensor - Compl or Incompl - SPD Test Result: Check mode result for the vehicle speed sensor.
# Codes(Include History) Number of codes - Min.: 0, Max.: 255 - Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up.
MIL MIL status - ON or OFF OFF: MIL off -
Time after DTC Cleared Time after DTC cleared - Min.: 0 min., Max.: 65535 min. Time after DTCs cleared Time elapsed since the DTCs were cleared (or shipment from the factory).
Distance from DTC Cleared Distance driven after DTC cleared - Min.: 0 km, Max.: 65535 km Distance driven after DTCs cleared
·

Distance driven since the DTCs were cleared.

·

(Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred.


Warmup Cycle Cleared DTC Warmup cycles after DTC cleared - Min.: 0, Max.: 255 -
·

Number of engine warmup since DTCs were cleared.

·

(Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred.


OBD Requirements Identifying OBD requirement - - - -
Number of Emission DTC Number of emissions-related DTCs - - - -
TC and TE1 TC and TE1 connection status for Active Test - ON or OFF - When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected.
Engine Start Time Engine start time - Min.: 0 ms,
Max.: 267000 ms
- Time necessary for the engine to start.
Swirl Control Valve VSV Status of VSV for swirl control valve - ON or OFF ON: Idling -
ACT VSV A/C cut status for Active Test - ON or OFF - "Control the A/C Cut Signal" Active Test support data.

Compression


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Engine Speed of Cyl #1 Engine speed for No. 1 - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same
·

Output only when the "Check the Cylinder Compression" Active Test is performed.

·

Indicates the speed of each cylinder when cranking.

Example - Normal: Engine speeds of all cylinders are approximately equal.

When No. 1 cylinder compression is low, "Engine Speed of Cyl #1" is approximately 300 rpm, and "Engine Speed of Cyl #2 to #4" is approximately 200 rpm.


Cause of Out of Range:
Cyl #1 compression goes down
Symptoms when out of range:
When the engine speeds of all cylinders are not equal, idling will be rough.
Engine Speed of Cyl #2 Engine speed for No. 2 - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #3 Engine speed for No. 3 - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #4 Engine speed for No. 4 - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Av Engine Speed of All Cyl Engine speed for all cylinders - Min.: 0 rpm, Max.: 51199 rpm -
·

Output only when the Active Test "Check the Cylinder Compression" is performed.

·

Indicates the average engine speed of all cylinders during cranking.



Vehicle Information


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
VN Turbo Type VN turbo type - Not Avl, Commo, Vacuum, CAN Com or DC Commo Indicates the VN turbo vane actuation method.
·

DC motor system.

·

Negative-pressure diaphragm system.

·

Step motor system.


Model Code Model code - - - -
Engine Type Engine type - - - Identifying engine type: 1KDFTV
Cylinder Number Cylinder number - Min.: 0, Max.: 255 - Identifying cylinder number: 4
Transmission Type Transmission type - MT or ECT 4th - Identifying transmission type:
·

MT (Manual transmission)

·

ECT 4th (Automatic transmission)


Destination Destination - - - -
Model Year Model year - Min.: 1900, Max.: 2155 - Identifying model year: 20##
System Identification System identification - - - Identifying engine type: Diesel

Diesel Injection


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Injection Volume Injection volume Calculated value Min.: 0 mm3/st, Max.: 1279.98 mm3/st Idling: 3.0 to 10 mm3/st
·

Injection amount for each combustion.

·

If injector assemblies are clogged fuel quality is poor, the fuel filter element sub-assembly is clogged, or engine friction increases, "Injection Volume" will increase.

·

If there is a malfunction due to low turbocharger pressure or a low intake air volume, the injection volume is limited and there is a lack of power.


Inj. FB Vol. for Idle Idle stability status integral control volume - Min.: -80 mm3/st, Max.: 79 mm3/st -10 to 10 mm3/st
·

When the actual engine speed does not match the target idling speed, this corrects the injection volume.

If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning.

·

Only calculated and reflected at idle.


Symptoms when out of range:
Engine friction problem, compression problem or injector breakdown
Inj Vol Feedback Learning Injection volume feedback learning value - Min.: -10 mm3/st, Max.: 9.92 mm3/st - -
Injection Feedback Val #1 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Injection Feedback Val #2 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Injection Feedback Val #3 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Injection Feedback Val #4 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Pilot 1 Injection Period Pilot 1 injection period Calculated value Min.: 0 μs, Max.: 65535 μs Idling: 370 to 470 μs Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur.
Symptoms when out of range:
Combustion noise, poor driveability, white smoke
Pilot 2 Injection Period Pilot 2 injection period Calculated value Min.: 0 μs, Max.: 65535 μs Idling: 400 to 500 μs Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur.
Symptoms when out of range:
Combustion noise, poor driveability, white smoke
Main Injection Period Main injection period Calculated value Min.: 0 μs, Max.: 65535 μs Idling: 450 to 650 μs
·

When the fuel pressure becomes 15000 kPa or less, "Main Injection Period" is set to 0.

·

When the engine will not start, confirm that injection is performed.

·

When P0093, P0627 or P0200 is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.

HINT:

As the engine stalls 1 minute after the MIL illuminates, freeze frame data cannot be checked.



After Injection Period After injection period Calculated value Min.: 0 μs, Max.: 65535 μs - Check to see if "After Injection Period" is not zero when the following symptoms occur:
Black smoke, poor driveability.
Pilot 1 Injection Timing Pilot 1 injection timing Calculated value Min.: -70°CA, Max.: 20°CA Idling after engine warmed up and vehicle under normal atmospheric pressure: -16 to -12°CA -
Pilot 2 Injection Timing Pilot 2 injection timing Calculated value Min.: -50°CA, Max.: 20°CA Idling after engine warmed up and vehicle under normal atmospheric pressure: -12 to -6°CA -
Main Injection Timing Main injection timing Calculated value Min.: -90°CA, Max.: 90°CA Idling after engine warmed up and vehicle under normal atmospheric pressure: 3 to 7°CA Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke.
After Injection Timing After injection timing Calculated Value Min.: -10°CA, Max.: 50°CA - -
Injector Memory Error Injector Memory Error Calculated value No Error or Error No Error If the injector compensation codes are not input into the new ECM, or if a injector compensation code of a different injector model or a compensation code representing a value which exceeds the compensation setting range is input into the new ECM, DTC P1601 is stored and "Injector Memory Error" displays "Error".
Symptoms when out of range:
Rough idling, poor driveability, black smoke, white smoke, combustion noise
Reju Pilot Quantity Learning Pilot quantity learning prohibition state Calculated value READY or NG - -
Pilot Quantity Learning State of "Pilot Quantity Learning" Calculated value Standby / Wait / Learn / Stop / Comple - If "Pilot Quantity Learning" is incomplete, the MIL illuminates and DTC P1601 is stored.
Injection Pressure Correction Injection pressure feedback compensation volume Calculated value Min.: -500 mm3/st, Max.: 780 mm3/st -400 to 400 mm3/st at standard temperature
·

When the (actual) fuel pressure is equal to the target fuel pressure, this value becomes 0.

·

This indicator can be used for diagnosing supply pump related malfunctions.

·

When this value (absolute value) is large, it indicates that the difference between the actual and target fuel pressure is also large.

A positive value indicates that the pressure feed is being increased due to insufficient pressure. A negative value indicates that pressure is being reduced due to excessive rail pressure.

When the suction control valve does not close properly, it causes rail overpressure, and this value slip to the negative volume side.


Cause of Out of Range:
·

Suction control valve malfunction

·

Clogged fuel filter element sub-assembly


Target Common Rail Pressure Target common rail pressure Target common rail pressure (ECU calculated value) Min.: 0 kPa, Max.: 250000 kPa 30000 to 160000 kPa when engine running
·

Inspect the (actual) fuel pressure, comparing it with the common rail target value.

·

Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions when idling after warm up the engine.


Fuel Press Fuel pressure Sensor output (fuel pressure sensor) Min.: 0 kPa, Max.: 250000 kPa Idling: 28000 to 40000 kPa
·

Fuel press is the actual common rail fuel pressure.

·

Inspect by comparing the fuel pressure with the target fuel pressure.

·

When in a stable condition such as when idling after warm up the engine, the fuel pressure is within +/-5000 kPa of the target fuel pressure.

·

The ECM uses fuel pressure for feedback control of the target fuel pressure via the supply pump.

The injection amount is determined based on the injection timing and fuel pressure.

Also, the spray pattern is selected based on the fuel pressure.

·

For startup, at least 25000 kPa of fuel pressure is needed (take care as there is a response lag when the pressure rises).

·

When the fuel pressure is below 25000 kPa, it may cause rough idling.

·

When the fuel pressure has decreased by 20000 kPa from the target fuel pressure, there may be a lack of power.

·

If the actual fuel pressure is 5000 kPa higher than the target fuel pressure, P1229 will be stored. When it is lower than the target fuel pressure, a lack of power will occur, but a DTC will not be stored.

·

When the fuel pressure is higher than 200000 kPa, DTC P0088 will be stored.


Cause of Out of Range:
·

Fuel supply pump assembly

·

High pressure pipes

·

Fuel pressure sensor

·

Injector assembly

·

Feed pump (fuel supply pump assembly)

·

Fuel filter element sub-assembly

·

Pressure limiter

·

Air in the fuel pipes

·

Lack of fuel


Symptoms when out of range:
Difficult to start, poor driveability, lack of power, abnormal combustion noise
Common Rail Pres Sens 2 Fuel pressure Sensor output (fuel pressure sensor) Min.: 0 kPa, Max.: 250000 kPa Idling: 28000 to 40000 kPa This is a backup output value from the fuel pressure sensor.
Cause of Out of Range:
·

Fuel supply pump assembly

·

High pressure pipes

·

Fuel pressure sensor

·

Injector assembly

·

Feed pump (fuel supply pump assembly)

·

Fuel filter element sub-assembly

·

Pressure limiter

·

Air in the fuel pipes

·

Lack of fuel


Symptoms when out of range:
Poor driveability, lack of power, abnormal combustion noise
Fuel Temperature Fuel temperature Sensor output (fuel temperature sensor) Min.: -40°C, Max.: 140°C Actual fuel temperature After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature.
Fuel Return Temp Fuel return temperature - Min.: -40°C, Max.: 140°C Idling after engine warmed-up: 35 to 85°C If the "Fuel Return Temp" value is not between 55°C (131°F) and 130°C (266°F), "Pilot Quantity Learning" is prohibited.
Target Pump SCV Current Final pump current target value Target value control (pump current) Min.: 0 mA, Max.: 4000 mA Idling: 923 to 1123 mA
·

ECU-calculated value for the suction control valve actuation target current.

·

Value is large when a high fuel pressure is desired.

·

Normally, the value is between 800 and 2500 mA.

·

If the value is stuck at 3000 mA or higher, it indicates that the operation is poor (poor movement due to deposits, etc.).

·

When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.


Cause of Out of Range:
·

Suction control valve malfunction

·

Clogged fuel filter element sub-assembly


Symptoms when out of range:
Difficulty starting, lack of power or rough idling
Pressure Discharge Valve Pressure discharge valve operation - ON or OFF ON: Pressure discharge valve open This is the ECM command.
Idle Injection Volume (Min) Idle minimum injection volume - Min.: 0 mm3/st, Max.: 39.8 mm3/st - This is the ECM command.

EGR System


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Target EGR Position EGR valve target opening amount ECU-calculated value based on sensors (mass air flow meter, manifold absolute pressure sensor, intake air temperature [built into mass air flow meter], etc.) Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 98%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Used for comparison to "Actual EGR Valve Pos.".


Symptoms when out of range:
·

When value is out of range and approaching 0%: mass air flow meter degradation, intake or exhaust system blockage

·

When value is out of range and approaching 100%: EGR pipe blockage


Actual EGR Valve Pos. EGR valve position Calculated from EGR valve position sensor Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 98%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Inspect while comparing to "Target EGR Valve Position".

·

Check the valve movement via the Active Test.

·

Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.


Symptoms when out of range:
·

EGR valve stuck open: Poor starts (engine does not stop), black smoke, white smoke, lack of power

·

EGR valve stuck closed: Increased turbo booster noise


EGR Close Lrn. Status EGR valve fully closed position learning status - OK or NG OK
·

"OK" means the fully closed position learning has completed normally.

·

When NG, the learned fully closed position may be outside of the normal range.

When NG, there may be foreign matter stuck in the valve.


HINT:

After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed.


EGR Operation Prohibit EGR operation prohibition - OK or NG OK: Possible to perform "Control the EGR Step Position" Active Test
·

OK: It is possible to perform the "Control the EGR Step Position" Active Test.

·

NG: It is not possible to perform the "Control the EGR Step Position" Active Test.


EGR Cut VSV EGR Cut VSV - ON or OFF - -

Diesel Throttle System


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Target Throttle Position Target throttle position Value calculated by ECM Min.: -128%, Max.: 127%
·

Throttle valve fully opened: 0%

·

Throttle valve fully closed: 100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Actual Throttle Position Actual diesel throttle position - Min.: -20%, Max.: 120% Idling after engine warmed-up: 55 to 90% Closing percentage of the throttle valve.
·

Fully closed: 100%.

·

Fully open: 0%.

HINT:

There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).



Symptoms when out of range:
·

Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle

·

Stuck open: Loud turbocharging sound, bad vibration when engine is stopped

·

When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h.


Throttle Close Learning Val. Throttle fully closed position learned value - Min.: 0 deg, Max.: 84 deg 11 to 21 deg
·

When the ignition switch is turned from on to off and 5 seconds elapse, learning of "Throttle Close Learning Val." will be complete.

·

When "Throttle Close Learning Val." is outside of the normal range, a foreign object may lodged in the throttle valve.

·

If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present.

However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed.


Diesel Throttle Learn Status Diesel throttle learning history - OK or NG OK
·

If the system is functioning properly, learning will be performed when the ignition switch is turned from on to off.

·

NG indicates that a foreign object may be lodged in the throttle valve or actuator components, or a disconnection/short exists in the signal wires.



VN Turbo System


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Target Booster Pressure Target booster pressure Value calculated by ECM Min.: 0 kPa, Max.: 320 kPa Driving vehicle on level surface at 3000 rpm with full load: 150 to 250 kPa
·

Inspect while comparing with "MAP".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 sec. or more, a feeling of a lack of power will occur.

·

When the vehicle is driven with the engine speed at 3000 rpm or more and the accelerator pedal fully depressed, "MAP" is approximately equal to "Target Booster Pressure".


VN Turbo Command VN turbo command value Controls the VN turbo vane opening position Min.: 0%, Max.: 100% 0 to 100%
·

"VN Turbo Command" is a command value.

·

0%: Vanes fully open (contraction of actuation rods)

·

90% or more: Vanes fully closed (extension of actuation rods)

·

When this value is large, the turbo works well.

·

There is no actual opening angle data to handle the VN turbo command value.


VN Turbo Max Angle VN turbo maximum opening amount - Min.: 0%, Max.: 100% 100%
HINT:

As this value displays the ideal constant upper limit, no matter what happens, this value should not change.


·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.


VN Turbo Min Angle VN turbo minimum opening amount - Min.: 0%, Max.: 100% 0%
HINT:

As this value displays the ideal constant lower limit, no matter what happens, this value should not change.


·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.



Diesel Starting


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Engine Speed (Starter Off) Engine speed when starter off - Min.: 0 rpm,
Max.: 1594 rpm
- Engine speed immediately after starting the engine.
Starter Count Starter on count - Min.: 0, Max.: 255 - Number of times the starter turned on from the time the ignition switch was turned to on.
Run Dist of Previous Trip Distance driven during previous trip - Min.: 0 km, Max.: 261 km - Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:
·

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

·

If DTCs for the diesel throttle, EGR valve, etc. are stored, confirm this item in the freeze frame data of the stored DTCs to determine the distance driven when the DTCs were stored. The distance driven can be used as a reference when troubleshooting.




Diesel Rough


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Electric Duty Feedback Value Electric load feedback value - Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 10 mm3/st Expected injection volume increase after the electrical load turns from off to on.
A/C Duty Feedback Value A/C load feedback value - Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 10 mm3/st Expected injection volume increase after the A/C turns from off to on.
PS Duty Feedback Value Power steering load feedback value - Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 10 mm3/st Expected injection volume increase after the power steering turns from off to on.

AT (for Automatic Transmission)


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Received MIL from ECT MIL status from ECT - ON or OFF ON: MIL ON -
Shift Position Sig from ECT Shift position signal from ECT - 1st, 2nd, 3rd, 4th, 5th or 6th - -
A/T Oil Temp from ECT ATF temperature from ECT - Min.: -40°C, Max.: 215°C With engine cold: Equal to ambient temperature -
SPD (NO) Output shaft speed - Min.: 0 rpm, Max.: 12750 rpm - -
ECT Lock Up Lock-up - ON or OFF ON: Lock-up operating -

ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Perform the Active Test.



Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the VSV for Swirl Control Valve Activate the VSV for swirl control valve ON/OFF -
Control the A/C Cut Signal Control the A/C signal ON/OFF Confirm that the vehicle is stopped and the engine is idling
Connect the TC and TE1 Turn on the TC and TE1 connection ON/OFF -
Activate the VSV for EGR Cut Activate vacuum switching valve (for EGR Cut) ON/OFF Confirm that the vehicle is stopped and the engine is idling
Control the EGR Step Position Control the electric EGR control valve assembly 0 to 100% Test is possible when the following conditions are met:
·

Ignition switch is on.

·

Engine is stopped.


Test the Turbo Charger Step Motor Activate the turbocharger 40 to 100% Test is possible when the following conditions are met:
·

Ignition switch is on.

·

Engine is stopped.


Test the Fuel Leak Pressurize the common rail interior and check for fuel leaks Stop/Start
·

Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when ON is selected

·

Above conditions preserved while test is ON


HINT:

If this Active Test is performed when the engine is cold, combustion may become unstable. However, this is not a malfunction. It is only necessary to confirm that the pressure rises to the target pressure and that there are no fuel leaks.


Activate the VN Turbo Open Activate the turbocharger ON/OFF Confirm that the engine is running.
Activate the EGR Valve Close Activate electric vacuum regulating valve assembly ON/OFF Confirm that the vehicle is stopped and the engine is idling
Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #4) injector fuel cut ON/OFF Fuel injection is stopped while the test is ON.
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning.


Check the Cylinder Compression Check the cylinder compression pressure* ON/OFF Fuel injection stops in all cylinders.
HINT:

*: When cranking the engine, the Active Test measures the speed of each cylinder. In this Active Test, the fuel of all cylinders is cut when the engine is cranked for approximately 10 seconds.


At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch to ON and turn the tester on.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4 and Av Engine Speed of All Cyl.


6.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, the "Check the Cylinder Compression" Active Test will start. Fuel injection for all cylinders is prohibited and the engine speed measurement of each cylinder enters standby mode.


7.

Crank the engine for about 10 seconds.

8.

Monitor the engine speed (Engine Speed of Cyl #1 to #4, Av Engine Speed of All Cyl) displayed on the tester.

HINT:

At first, the tester display will show the engine speed measurement of each cylinder to be extremely high. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.


NOTICE:
·

After the "Check the Cylinder Compression" Active Test is turned on, it will automatically turn off after 255 seconds.

·

When the "Check the Cylinder Compression" test is off and the engine is cranked, the engine will start.

·

If the "Check the Cylinder Compression" test needs to be performed after it is turned on and performed once, press "EXIT" to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.

·

Use a fully-charged battery.




SYSTEM CHECK


a.

Activate the Pressure Discharge Valve Check

HINT:
·

This is the procedure for troubleshooting fuel pressure control malfunctions and combustion problems.

·

Malfunctions can be determined by checking the fuel pressure when performing a fuel cut and operating the pressure discharge valve with the intelligent tester.

·

During "Pressure Discharge Valve Check", the intelligent tester measures the fuel pressure while the engine is running, after the engine is stopped, and after the pressure discharge valve operates.



i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.
A204072

Turn the tester on.

NOTICE:

Confirm the following conditions:

·

Engine is idling.

·

Vehicle is stopped.

·

Fuel pressure is not extremely high (below 100000 kPa).

·

Fuel pressure is not extremely low (higher than 26000 kPa).

·

Fuel pressure sensor is normal.

·

Battery voltage is higher than 8 V.



HINT:

When the common rail pressure is unstable, the fuel pressure may decrease to a level where the test cannot be performed. In this situation, wait until the common rail pressure meets the test condition, and then perform the test.



iv.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check.

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 61 2109

v.
A204067

Press "Next".


vi.
A204068

Press "Next" again to proceed.


vii.
A204069

Select the "Pressure Discharge Valve Check" type.

HINT:
·

"Close to Open Check" opens the pressure discharge valve after the engine stops.

·

"Always Closed Check" holds the pressure discharge valve closed during the check.




viii.

Press "Next".


ix.

Perform troubleshooting based on the measurement results.

A204070

HINT:
·

During "Close to Open Check", if there is no large change in fuel pressure when the pressure discharge valve is closed while the engine is running and after the engine is stopped, and if the value is 0 kPa when the pressure discharge valve is open, the system is normal.

·

Perform "Always Closed Check" if the value is not 0 kPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.

·

If the fuel temperature is high, perform "Pressure Discharge Valve Check" after the fuel has cooled to the outside air temperature.

·

If a large amount of fuel is leaking, the fuel pressure decreases when the engine is stopped. However, the condition of the pressure discharge valve can still be determined by comparing the measurement results of "Close to Open Check" and "Always Closed Check".


A303297
5.365,0.083 6.76,0.448 1.396,0.365 10 false Fuel Press Recorded 0.74,1.438 2.271,1.635 1.531,0.198 10 false Fuel Press 0.75,2.635 2.281,2.938 1.531,0.302 10 false (Close to Open Check) 2.719,1.833 3.167,2.031 0.448,0.198 10 false 0 kPa 0.75,2.49 2.281,2.688 1.531,0.198 10 false Fuel Press 0.76,1.594 2.25,1.865 1.49,0.271 10 false (Always Closed Check) 2.75,3.219 3.198,3.417 0.448,0.198 10 false 0 kPa 0.75,3.667 2.417,4.083 1.667,0.417 10 false Engine Speed 2.75,3.885 3.198,4.083 0.448,0.198 10 false 0 rpm 2.833,4.333 3.281,4.531 0.448,0.198 10 false On 2.833,4.667 3.135,4.865 0.302,0.198 10 false Off 0.5,4.49 2.26,4.74 1.76,0.25 10 false Fuel Cut Operation Signal 0.5,5.219 2.104,5.719 1.604,0.5 10 false Pressure Discharge Valve Operation Prohibition 2.833,5.167 3.135,5.365 0.302,0.198 10 false Off 2.833,5.469 3.281,5.667 0.448,0.198 10 false On 2.396,5.833 3.25,6.073 0.854,0.24 10 false Closed (on) 2.833,6.135 3.135,6.333 0.302,0.198 10 false Off 2.479,6.49 3.333,6.729 0.854,0.24 10 false Open (on) 2.427,6.802 3.281,7.042 0.854,0.24 10 false Closed (on) 2.833,7.083 3.135,7.281 0.302,0.198 10 false Off 2.875,7.438 5.542,7.688 2.667,0.25 10 false Pressure Discharge Valve Operation Start 0.104,5.917 2.323,6.5 2.219,0.583 10 false Pressure Discharge Valve Operation (Always Closed Check) 0.094,6.781 2.302,7.365 2.208,0.583 10 false Pressure Discharge Valve Operation (Close to Open Check)