Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  U0101  Lost Communication with TCM  


DESCRIPTION

The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).

If there is a problem with this communication, the ECM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0101 Lost Communication with TCM Both conditions are met for 1.25 seconds (1 trip detection logic):
·

The battery voltage is 10.5 V or higher.

·

No communication between the ECM and TCM.


·

ECM

·

TCM

·

ECM to TCM circuit


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

U0101
DTC Detection Drive Pattern Ignition switch to ON for 3 seconds

WIRING DIAGRAM

A255256
0.958,1.031 1.385,1.229 0.427,0.198 10 false CAN+ 1.479,1.031 1.833,1.26 0.354,0.229 10 false G41 1.531,0.844 1.781,1.042 0.25,0.198 10 false 21 1.479,1.729 1.781,1.927 0.302,0.198 10 false G41 1.531,1.542 1.781,1.74 0.25,0.198 10 false 20 1.479,2.302 1.781,2.5 0.302,0.198 10 false G41 1.573,2.115 1.781,2.313 0.208,0.198 10 false 5 1.479,2.896 1.781,3.094 0.302,0.198 10 false C24 0.813,3.438 1.188,3.635 0.375,0.198 10 false TCM 6.052,3.542 6.49,3.771 0.438,0.229 10 false ECM 1.573,2.719 1.781,2.917 0.208,0.198 10 false 1 2.76,2.177 2.969,2.375 0.208,0.198 10 false 1 2.5,2.177 2.708,2.375 0.208,0.198 10 false 2 0.958,1.719 1.385,1.917 0.427,0.198 10 false CAN- 5.833,1.031 6.26,1.229 0.427,0.198 10 false CAN+ 5.594,0.927 5.844,1.125 0.25,0.198 10 false 22 6.063,3.396 6.448,3.594 0.385,0.198 10 false G38 5.594,1.625 5.844,1.823 0.25,0.198 10 false 21 5.833,1.719 6.26,1.917 0.427,0.198 10 false CAN- 0.958,2.302 1.385,2.5 0.427,0.198 10 false BATT 1.135,2.906 1.396,3.104 0.26,0.198 10 false E1 2.563,2.438 2.875,2.615 0.313,0.177 10 false EFI 3.24,2.458 3.927,2.708 0.688,0.25 10 false BATT P/I 4.406,2.844 5.063,3.156 0.656,0.313 10 false Battery

PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
DTC U0101 is output A
DTC U0101 and other DTCs are output B


HINT:

If any DTCs other than U0101 are output, troubleshoot those DTCs first.




A

2.INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)

B

2.INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)
a.
C216560C05
0.781,0.354 1.167,0.615 0.385,0.26 2.167,0.365 2.552,0.625 0.385,0.26 2.125,2.708 2.281,1.969 true 1.396,2.729 1.302,1.958 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.854,0.406 1.167,0.604 0.313,0.198 10 false C24 2.24,0.417 2.552,0.615 0.313,0.198 10 false G41 1.781,2.74 2.344,2.938 0.563,0.198 10 false 5 (BATT) 1.198,2.75 1.667,2.927 0.469,0.177 10 false 1 (E1)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G41-5 (BATT) - C24-1 (E1) Ignition switch ON 11 to 14 V



c.

Reconnect the TCM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-22 (CAN+) - G41-21 (CAN+) Always Below 1 Ω
G38-21 (CAN-) - G41-20 (CAN-) Always Below 1 Ω
G38-22 (CAN+) or G41-21 (CAN+) - Body ground or other terminals Always 1 MΩ or higher
G38-21 (CAN-) or G41-20 (CAN-) - Body ground or other terminals Always 1 MΩ or higher



d.

Reconnect the TCM connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC U0101 is output B




A

END

B