Refer to DTC P0046 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0046).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0299 | Turbocharger / Supercharger Underboost | The pressure is 55 kPa below the Target Booster Pressure for 80 seconds at an engine speed of 2800 to 4400 rpm (1 trip detection logic). | ·
Turbocharger sub-assembly ·
Extremely low battery voltage (P0560 output simultaneously) ·
Disconnected pipe between turbo and intake manifold ·
Disconnected manifold absolute pressure sensor hose ·
Throttle valve stuck closed ·
Electric EGR control valve assembly does not close ·
Exhaust system or intake system modified (leading to increased pressure loss, etc.) ·
Manifold absolute pressure sensor ·
Injection system (reduction in fuel injection volume) ·
Fuel filter element sub-assembly clog ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0299 | ·
Target Booster Pressure ·
MAP |
If DTC P0299 is stored due to the variable nozzle being stuck open, the following symptoms may appear:
Lack of power
Vehicle surge or hesitation under light or medium load
| DTC Detection Drive Pattern | Accelerate vehicle with accelerator depressed halfway or more starting from a speed of 120 km/h (75 mph) or more for 2 minutes (make sure gear is fixed and does not change) |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Comparison of the data list items manifold absolute pressure and target booster pressure during acceleration under medium to high engine speeds can be used to determine the state of the problem.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0299 is output | A |
| P0299 and other DTCs are output | B |
A
B
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART
Enter the following menus: Powertrain / Engine and ECT / DTC.
Record the stored DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| Difference between Fuel Press and Target Common Rail Pressure of freeze frame data is 20000 kPa or more | A |
| Except above | B |
A
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>Lack of Power or Hesitation
B
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>Lack of Power or Hesitation