Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) U

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Start the engine.


f.

Turn the intelligent tester on.


g.
A175559
1.177,2.229 2.25,2.385 false 1.156,1.031 1.771,0.208 1.771,0.208 1.969,0.208 false 0.073,0 0.708,0.188 0.635,0.188 10 false Example: 2.021,0.135 3.073,0.292 1.052,0.156 10 false Pull Down Menu 2.281,2.323 3.198,2.677 0.917,0.354 10 false Measurement Group

Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:
·

To display the list box, press the pull down menu button next to "Primary". Then select a measurement group.

·

When you select a measurement group, the ECU data belonging to that group is displayed.


·

Measurement Group List / Description

·

All Data / All data

·

Primary / -

·

Engine Control / Engine control system related data

·

Vehicle Information / Vehicle information

·

Monitor Status / Monitor status related data

·

AF Control System / Not Applicable

·

Catalytic Converter / Not Applicable

·

Evaporative / Not Applicable

·

A/T / Automatic transaxle system related data

·

ETCS / Not Applicable

·

Misfire / Not Applicable

·

Compression / Data used during "Check the Cylinder Compression" Active Test

·

HC Adsorber System / Not Applicable

·

Diesel Driving / Driving condition data

·

Diesel Injection / Fuel system related data

·

Diesel EGR / EGR system related data

·

Diesel Throttle / Diesel throttle system related data

·

Diesel VN Turbo / VN turbo related data

·

Diesel Exhaust / Exhaust system related data

·

Diesel Starting / "Difficult to start" related data

·

Diesel Rough / "Rough idle" related data

·

Diesel Power / "Lack of power" related data





h.

Check the values by referring to the table below.

NOTICE:
·

Normal Condition: If no idling conditions are specified, the shift lever is in the neutral position, and the A/C switch and all accessory switches are OFF.

·

"Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.





Engine Control


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Sensor output (speed sensor) Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed Cause of Out of Range:
·

Speed sensor

·

Speed sensor circuit


Target Idle Engine Speed Target Idling Engine Speed Target idling speed (ECM calculated value) Min.: 0 rpm, Max.: 10000 rpm - -
Engine Speed Engine speed Sensor output (crankshaft position sensor) Min.: 0 rpm, Max.: 6000 rpm
·

50 to 400 rpm: Cranking

·

700 to 800 rpm: Idling with warm engine


When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.
Cause of Out of Range:
·

Crankshaft position sensor

·

Crankshaft position sensor circuit


Calculate Load Load calculated by ECM Calculated by ECM Min.: 0%, Max.: 100%
·

Idling: 3 to 25%

·

Running without load (2500 rpm): 20 to 30%


Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100.
Cause of Out of Range:
Malfunction in which turbo pressure or Mass Air Flow decreases
Results of real-vehicle check:
·

Ignition switch ON: 0%

·

Cranking: 93.7%

·

Idling (warm up the engine): 14.5% (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 24.3%

·

Running without load (4000 rpm): 31.7%

·

Driving with the accelerator fully open at 2000 rpm: 99.6%

·

Driving with the accelerator fully open at 3000 rpm: 90.1%


MAF Air flow rate from mass air flow meter Sensor output (mass air flow meter) Min.: 0 gm/s, Max.: 400 gm/s
·

Idling: 4 to 20 gm/s

·

Running without load (2000 rpm): 14 to 58 gm/s


HINT:

Depends on EGR rate


·

Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.

·

If the value is always approximately 0 gm/s:

·

Mass air flow meter power source circuit is open.

·

VG circuit is open or shorted.

·

EVG circuit is open.



Cause of Out of Range:
·

Mass air flow meter

·

Mass air flow meter circuit

·

Intake related clog or leak

·

Exhaust related clog

·

Turbocharger sub-assembly

·

Leak or clog in passages for turbocharger

·

Malfunction in which EGR valve does not close


Results of real-vehicle check:
·

Ignition switch ON: 0.29 gm/s

·

Cranking: 6.07 gm/s

·

Idling (warm up the engine): 5.07 gm/s (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 27.95 gm/s

·

Running without load (4000 rpm): 98.42 gm/s

·

Driving with the accelerator fully open at 2000 rpm: 79.56 gm/s

·

Driving with the accelerator fully open at 3000 rpm: 151.93 gm/s


Symptoms when out of range:
Rough idling
Atmosphere Pressure Atmospheric pressure value Sensor output (atmospheric pressure sensor (built into ECM)) Min.: 0 kPa, Max.: 255 kPa Actual atmospheric pressure
·

With the ignition switch ON, when the difference between the atmospheric pressure sensor and intake manifold absolute pressure is 10 kPa or more, there is a malfunction in one of the sensors.

·

With the ignition switch ON, when the atmospheric pressure is 0 kPa or 140 kPa, there is a malfunction in the sensor circuit.

·

Standard atmospheric pressure: 101 kPa.

·

For every 100 m increase in elevation, pressure drops by 1 kPa.

This varies by weather (high atmospheric pressure, low atmospheric pressure).


Cause of Out of Range:
Atmospheric pressure sensor itself has failed (atmospheric pressure sensor is inside the ECM)
MAP Absolute pressure inside intake manifold Sensor output (manifold absolute pressure sensor) Min.: 0 kPa, Max.: 320 kPa
·

Idling: 93 to 106 kPa (depends on barometric pressure and amount of EGR)

·

Engine running at 3000 rpm: 106 to 125 kPa


·

When the ignition switch is ON or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa).

Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure.

·

Inspect while comparing with "Target Booster Pressure".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.


Cause of Out of Range:
·

Manifold absolute pressure sensor

·

Intake related clog or leak

·

Exhaust related clog

·

Turbocharger sub-assembly

·

Leak or clog in passages for turbocharger

·

EGR valve stuck open

·

Exhaust leak

·

Throttle valve stuck closed


Results of real-vehicle check:
·

Ignition switch ON: 101 kPa

·

Cranking: 100 kPa

·

Idling (warm up the engine): 99 kPa (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 111 kPa

·

Running without load (4000 rpm): 115 kPa

·

Driving with the accelerator fully open at 2000 rpm: 160 kPa

·

Driving with the accelerator fully open at 3000 rpm: 210 kPa


Symptoms when out of range:
Lack of power
Coolant Temp Engine coolant temperature Sensor output (engine coolant temperature sensor) Min.: -40°C, Max.: 140°C After warming up engine: 70 to 90°C (158 to 194°F)
·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

·

After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal.


Cause of Out of Range:
·

Engine coolant temperature sensor

·

Thermostat


Symptoms when out of range:
Difficulty starting when engine is cold, rough idle, black smoke, lack of power
Intake Air Intake air temperature Sensor output (intake air temperature sensor (built into mass air flow meter)) Min.: -40°C, Max.: 140°C Equivalent to temperature at location of mass air flow meter
·

After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal.

·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.


Cause of Out of Range:
Intake air temperature sensor
Intake Air Temp (Turbo) Intake air temperature after intercooler Sensor output (intake air temperature sensor after intercooler) Min.: -40°C, Max.: 190°C 70°C (158°F) or less
·

This is the intake air temperature at the intake manifold (after the intercooler).

·

During fail-safe operation, the value is set to 165°C (329°F). As the value is set to a high temperature, the turbo pressure may be suppressed and there may be a lack of power.


Cause of Out of Range:
Decreased cooling efficiency of intercooler (contamination, clogging)
Engine Run Time Engine run time Result of ECU calculations (using the engine speed) Min.: 0 sec., Max.: 65535 sec. Time after the ignition switch turned to ON Time passed since the ignition switch was turned to ON.
Initial Engine Coolant Temp Initial engine coolant temperature Sensor output when engine started Min.: -40°C, Max.: 120°C Engine coolant temperature when engine started For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine.
Initial Intake Air Temp Initial intake air temperature Sensor output when engine started Min.: -40°C, Max.: 120°C Intake air temperature when engine started -
Battery Voltage Battery voltage - Min.: 0 V, Max.: 15 V 11 to 14 V If 11 V or less, characteristics of some electrical components change.
Results of real-vehicle check:
·

Ignition switch ON: 12.1 V

·

Cranking (with engine warmed up): 11.2 V

·

Idling (warm up the engine): 13.1 V

·

Running without load (2500 rpm): 13.6 V

·

Running without load (4000 rpm): 13.6 V

·

Driving with the accelerator fully open at 2000 rpm: 13.3 V

·

Driving with the accelerator fully open at 3000 rpm: 13.5 V


Symptoms when out of range:
If 5 V or less, starting becomes difficult
Alternate Duty Ratio Alternator generation duty ratio Duty value from ALT terminal Min.: 0%, Max.: 100%
·

No electrical load at idling:

20 to 60%


·

High electrical load at idling:

100%


·

This is outputs the alternator generation duty and is used to determine the electrical load.

·

Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction.

·

Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device like the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, like battery deterioration.


Cause of Out of Range:
·

Battery deterioration

·

Alternator malfunction

·

Electric load, lights, etc.


Results of real-vehicle check:
Idling (no electrical load) (warm up the engine): 40% (2 minutes after starting the vehicle)
Glow Control Unit Duty Glow Control Unit Duty Result of ECU calculations Min.: 0%, Max.: 127.5% - This is the ECM command.
Accel Position Accelerator position status
·

Accelerator pedal position sensor opening position

·

ETC requested opening position

·

Cruise requested opening position

·

VSC requested opening position


Min.: 0%, Max.: 100%
·

Accelerator pedal released:

0%

·

Accelerator pedal fully depressed:

100%


·

"Accel Position" is the accelerator opening amount (%) for engine control use.

·

When the accelerator pedal position sensor output itself (Accelerator Position 1, Accelerator Position 2) is in the normal voltage range, another actuator malfunction has caused the fail-safe function to restrict the accelerator.

·

Without cruise, ETC or VSC requests, and without accelerator restriction by the fail-safe function, this is adjusted in proportion to the amount the accelerator pedal is depressed by the driver.

·

Accelerator pedal released: 0%

·

Accelerator pedal fully depressed: 100%


Results of real-vehicle check:
·

Ignition switch ON: 0% (accelerator pedal released)

·

Running without load (2500 rpm): 15.62%

·

Running without load (4000 rpm): 28.90%


HINT:

Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".


Accel Sens. No.1 Volt % Accelerator position No. 1 Sensor output (Accelerator pedal position sensor) Min.: 0%, Max.: 100%
·

Accelerator pedal released:

10 to 22%

·

Accelerator pedal fully depressed:

52 to 90%


Read value with ignition switch ON (do not start engine).
HINT:

Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".


Accel Sens. No.2 Volt % Accelerator position No. 2 Sensor output (Accelerator pedal position sensor) Min.: 0%, Max.: 100%
·

Accelerator pedal released:

24 to 40%

·

Accelerator pedal fully depressed:

68 to 99%


Read value with ignition switch ON (do not start engine).
HINT:

Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".


Starter Signal Starter signal - ON or OFF ON: Cranking Ignition switch (STA) output:
·

ON: Starter is operating

·

OFF: Starter is not operating


Cause of Out of Range:
·

OFF malfunction (ignition switch (STA) is ON but the signal is OFF and the starter is operating): Wire harness is open or shorted to ground

·

ON malfunction (ignition switch (STA) is off but the signal is ON and the starter is not operating): Wire harness is shorted to +B

·

Operation malfunction: ignition switch malfunction, starter relay malfunction, starter malfunction, battery or battery cable is defective, or wire harness is open or shorted


Symptoms when out of range:
·

Ignition switch is ON but the starter does not operate: Starting is not possible

·

Ignition switch is off but the starter continues to operate: STA signal malfunction (P0617) is stored


Clutch Switch Clutch switch Switch output (Clutch switch assembly for cruise control system) ON or OFF ON: Clutch pedal depressed When this item displays "OFF" with the clutch pedal depressed, the shock when accelerating and decelerating the vehicle becomes larger and pilot quality learning cannot be performed.
Symptoms when out of range:
The cruise control, pilot quantity learning, etc. may not function properly or may not function at all.
Stop Light Switch Stop light switch Switch output (stop light switch) ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


Stop light switch (STP) operation condition:
·

ON: Light is on (Brake pedal is depressed)

·

OFF: Light is off (Brake pedal is released)


Cause of Out of Range:
·

OFF malfunction: Wire harness (stop light switch to ECM, stop light switch to +B) open or shorted to ground

·

ON malfunction: Wire harness (stop light switch to ECM) shorted to +B

·

Stop light switch


Symptoms when out of range:
Stop light switch malfunction DTC P0504 is stored
A/C Signal A/C (Air Conditioner) signal A/C operation signal output from A/C amplifier
·

ON: Operating

·

OFF: Not operating


ON or OFF ON: A/C on
·

A/C switch

·

A/C amplifier

·

A/C system malfunction, wire harness between A/C amplifier and ECU open or shorted


Symptoms when out of range:
OFF malfunction (OFF even when A/C switch is turned on):
·

Engine speed decreases temporarily when the A/C is operating.


Immobiliser Communication Immobiliser communication - ON or OFF
·

ON: Normal

·

OFF: Engine cannot be started due to immobiliser communication malfunction


Cause of Out of Range:
·

Use of a non-registered key

·

Key battery is fully depleted


Check Mode Check mode - ON or OFF ON: Check mode on Check Mode: The mode in which certain DTCs can be detected more easily and with higher sensitivity.
Complete Parts Monitor Complete parts monitor - Not Avl or Avail - -
# Codes(Include History) Number of codes - Min.: 0, Max.: 255 - Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up.
MIL MIL status - ON or OFF OFF: MIL off -
MIL ON Run Distance Distance traveled with MIL on Result of ECU calculations (using the vehicle speed) Min.: 0 km, Max.: 65535 km Distance traveled after DTC stored
·

Distance traveled after a DTC is stored.

·

Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the intelligent tester.


Running Time from MIL ON Running time after MIL turns on - Min.: 0 min., Max.: 65535 min. Running time after MIL turns on
·

Engine run time since the MIL illumination.

·

Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the intelligent tester.


Time after DTC Cleared Time after DTC cleared - Min.: 0 min., Max.: 65535 min. Time after DTCs cleared Time elapsed since the DTCs were cleared (or shipment from the factory).
Distance from DTC Cleared Distance driven after DTC cleared - Min.: 0 km, Max.: 65535 km Distance driven after DTCs cleared
·

Distance driven since the DTCs were cleared.

·

(Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred.


Warmup Cycle Cleared DTC Warmup cycles after DTC cleared - Min.: 0, Max.: 255 -
·

Number of engine warmup since DTCs were cleared.

·

(Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred.


OBD Requirements Identifying OBD requirement - - - Euro-OBD
Number of Emission DTC Number of emissions-related DTCs - - - -
TC and TE1 TC and TE1 connection status for Active Test - ON or OFF - When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected.
Engine Start Time Engine start time - Min.: 0 ms, Max.: 267000 ms - Time necessary for the engine to start.
Swirl Control Valve VSV Status of VSV for swirl control valve - ON or OFF ON: Idling -
ACT VSV A/C cut status for Active Test - ON or OFF - "Control the A/C Cut Signal" Active Test support data.

Compression


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Engine Speed of Cyl #1 Engine speed for No. 1 cylinder - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same
·

Output only when the "Check the Cylinder Compression" Active Test is performed.

·

Indicates the speed of each cylinder when cranking.

Example - Normal: Engine speeds of all cylinders are approximately equal.

When No. 1 cylinder compression is low, "Engine Speed of Cyl #1" is approximately 300 rpm, and "Engine Speed of Cyl #2 to #4" is approximately 200 rpm.


Cause of Out of Range:
Cyl #1 compression goes down
Symptoms when out of range:
When the engine speeds of all cylinders are not equal, idling will be rough.
Engine Speed of Cyl #2 Engine speed for No. 2 cylinder - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #3 Engine speed for No. 3 cylinder - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #4 Engine speed for No. 4 cylinder - Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Av Engine Speed of All Cyl Engine speed for all cylinders - Min.: 0 rpm, Max.: 51199 rpm -
·

Output only when the Active Test "Check the Cylinder Compression" is performed.

·

Indicates the average engine speed of all cylinders during cranking.



Vehicle Information


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
VN Turbo Type VN turbo type - Not Avl, Commo, Vacuum, CAN com, DC DC*
HINT:

*: "DC" refers to the DC motor system.


Indicates the VN turbo vane actuation method.
·

DC motor system.

·

Negative-pressure diaphragm system.

·

Step motor system.


Model Code Model code - - - Identifying model code
Engine Type Engine type - - - Identifying engine type: 1KDFTV
Cylinder Number Cylinder number - Min.: 0, Max.: 255 - Identifying cylinder number: 4
Transmission Type Transaxle type - MT or ECT 5th - Identifying transaxle type:
·

MT: Manual transaxle

·

ECT 5th: Automatic transaxle


Destination Destination - - - Identifying destination
Model Year Model year - Min.: 1900, Max.: 2155 - Identifying model year: 20##

Diesel Injection


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Injection Volume Injection volume Calculated value Min.: 0 mm3/st, Max.: 1279.98 mm3/st Idling: 2 to 11 mm3/st
·

Injection amount for each combustion.

·

If injector assemblies are clogged fuel quality is poor, the fuel filter element sub-assembly is clogged, or engine friction increases, "Injection Volume" will increase.

·

If there is a malfunction due to low turbocharger pressure or a low intake air volume, the injection volume is limited and there is a lack of power.


Results of real-vehicle check:
·

Cranking: 47.51 mm3/st

·

Idling (warm up the engine and A/C off): 7.30 mm3/st

·

Running without load (2500 rpm): 12.30 mm3/st

·

Running without load (4000 rpm): 14.27 mm3/st

·

Driving with the accelerator fully open at 2000 rpm: 74.96 mm3/st

·

Driving with the accelerator fully open at 3000 rpm: 78.90 mm3/st


Inj. FB Vol. for Idle Idle stability status integral control volume - Min.: -80 mm3/st, Max.: 79 mm3/st -10 to 10 mm3/st
·

When the actual engine speed does not match the target idling speed, this corrects the injection volume.

If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning.

·

Only calculated and reflected at idle.


Results of real-vehicle check:
Idling (warm up the engine): 0.88 mm3/st
Symptoms when out of range:
Engine friction problem, compression problem or injector breakdown
Inj Vol Feedback Learning Injection volume feedback learning value - Min.: -10 mm3/st, Max.: 9.92 mm3/st - -
Idle Signal Output Value Idle Signal Output Value - Min.: 0, Max.: 255
·

Idling: 1

·

Not idling: 0


·

Piezo injector has big operation noise when idling. To reduce the noise level, this item lowers driving energy of when idling. This item displays the value for controlling driving energy

·

If the value is abnormal, DTC P1626 and P1627 will be stored.

·

If the injector is not Piezo injector, the value will be always "0".


Injection Feedback Val #1 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Injection Feedback Val #2 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Injection Feedback Val #3 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Injection Feedback Val #4 Injection volume correction for each cylinder Learned value Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Cause of Out of Range:
·

Injector clogging

·

Injector deterioration

·

Decrease in cylinder compression

·

Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)


Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Pilot 1 Injection Period Pilot 1 injection period Calculated value Min.: 0 μs, Max.: 65535 μs Idling: 100 to 400 μs Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur.
Results of real-vehicle check:
·

Cranking: 244 μs

·

Idling (warm up the engine): 225 μs

·

Running without load (2500 rpm): 171 μs

·

Running without load (4000 rpm): 0 μs

·

Driving with the accelerator fully open at 2000 rpm: 183 μs

·

Driving with the accelerator fully open at 3000 rpm: 0 μs


Symptoms when out of range:
Combustion noise, poor driveability, white smoke
Pilot 2 Injection Period Pilot 2 injection period Calculated value Min.: 0 μs, Max.: 65535 μs Idling: 100 to 400 μs Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur.
Results of real-vehicle check:
·

Cranking: 574 μs

·

Idling (warm up the engine): 227 μs (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 156 μs

·

Running without load (4000 rpm): 171 μs

·

Driving with the accelerator fully open at 2000 rpm: 165 μs

·

Driving with the accelerator fully open at 3000 rpm: 161 μs


Symptoms when out of range:
Combustion noise, poor driveability, white smoke
Main Injection Period Main injection period Calculated value Min.: 0 μs, Max.: 65535 μs Idling: 200 to 500 μs
·

When the fuel pressure becomes 15000 kPa or less, "Main Injection Period" is set to 0.

·

When the engine will not start, confirm that injection is performed.

·

When P0093, P0627 or P062D is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.

HINT:

As the engine stalls 1 minute after the MIL illuminates, freeze frame data cannot be checked.



Results of real-vehicle check:
·

Cranking: 609 μs

·

Idling (warm up the engine): 326 μs (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 280 μs

·

Running without load (4000 rpm): 300 μs

·

Driving with the accelerator fully open at 2000 rpm: 628 μs

·

Driving with the accelerator fully open at 3000 rpm: 567 μs


After Injection Period After injection period Calculated value Min.: 0 μs, Max.: 65535 μs - Check to see if "After Injection Period" is not zero when the following symptoms occur:
Black smoke, poor driveability.
Pilot 1 Injection Timing Pilot 1 injection timing Calculated value Min.: -70°CA, Max.: 20°CA Idling after engine warmed up and vehicle under normal atmospheric pressure: -13.3 to -9.3°CA Results of real-vehicle check:
·

Ignition switch ON: -11.3°CA

·

Cranking: -6.0°CA

·

Idling (warm up the engine): -11.2°CA

·

Running without load (2500 rpm): -23.2°CA

·

Running without load (4000 rpm): -31.4°CA

·

Driving with the accelerator fully open at 2000 rpm: -29.2°CA

·

Driving with the accelerator fully open at 3000 rpm: -33.5°CA


Pilot 2 Injection Timing Pilot 2 injection timing Calculated value Min.: -50°CA, Max.: 20°CA Idling after engine warmed up and vehicle under normal atmospheric pressure: -8.8 to -4.8°CA Results of real-vehicle check:
·

Ignition switch ON: -6.8°CA

·

Cranking: -3.5°CA

·

Idling (warm up the engine): -6.8°CA

·

Running without load (2500 rpm): -11.2°CA

·

Running without load (4000 rpm): -19.9°CA

·

Driving with the accelerator fully open at 2000 rpm: -17.0°CA

·

Driving with the accelerator fully open at 3000 rpm: -21.0°CA


Main Injection Timing Main injection timing Calculated value Min.: -90°CA, Max.: 90°CA Idling after engine warmed up and vehicle under normal atmospheric pressure: -2.8 to 1.2°CA Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke.
Results of real-vehicle check:
·

Ignition switch ON: 0.1°CA

·

Cranking: -1.0°CA

·

Idling (warm up the engine): -0.8°CA

·

Running without load (2500 rpm): -0.8°CA

·

Running without load (4000 rpm): -3.7°CA

·

Driving with the accelerator fully open at 2000 rpm: -1.4°CA

·

Driving with the accelerator fully open at 3000 rpm: -3.0°CA


After Injection Timing After injection timing Calculated Value Min.: -10°CA, Max.: 50°CA - Results of real-vehicle check:
·

Ignition switch ON: 19.2°CA

·

Cranking: 0°CA

·

Idling (warm up the engine): 19.2°CA

·

Running without load (2500 rpm): 19.2°CA

·

Running without load (4000 rpm): 19.2°CA

·

Driving with the accelerator fully open at 2000 rpm: 22.4°CA

·

Driving with the accelerator fully open at 3000 rpm: 22.4°CA


Injector Memory Error Injector Memory Error Calculated value No Error or Error No Error If the injector compensation codes are not input into the new ECM, or if an injector compensation code of a different injector model or a compensation code representing a value which exceeds the compensation setting range is input into the new ECM, DTC P062F is stored and "Injector Memory Error" displays "Error".
Symptoms when out of range:
Rough idling, poor driveability, black smoke, white smoke, combustion noise
Reju Pilot Quantity Learning Pilot quantity learning prohibition state Calculated value READY or NG - The status is only displayed while performing "Pilot Quantity Learning".
Pilot Quantity Learning State of "Pilot Quantity Learning" Calculated value Standby, Wait, Learn, Stop, Comple -
·

The status is only displayed while performing "Pilot Quantity Learning".

·

If "Pilot Quantity Learning" is incomplete, the MIL illuminates and DTC P062F is stored.


Injection Pressure Correction Injection pressure feedback compensation volume Calculated value Min.: -500 mm3/st, Max.: 780 mm3/st -400 to 400 mm3/st at standard temperature
·

When the (actual) fuel pressure is equal to the target fuel pressure, this value becomes 0.

·

This indicator can be used for diagnosing supply pump related malfunctions.

·

When this value (absolute value) is large, it indicates that the difference between the actual and target fuel pressure is also large.

A positive value indicates that the pressure feed is being increased due to insufficient pressure. A negative value indicates that pressure is being reduced due to excessive rail pressure.

When the suction control valve does not close properly, it causes rail overpressure, and this value and the "Pump SCV Learning Value" slip to the negative volume side.


Cause of Out of Range:
·

Suction control valve malfunction

·

Clogged fuel filter element sub-assembly


Results of real-vehicle check:
·

Ignition switch ON: 2.0 mm3/st

·

Cranking: 0 mm3/st

·

Idling (warm up the engine): 1.9 mm3/st (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 2.0 mm3/st

·

Running without load (4000 rpm): 7.9mm3/st

·

Driving with the accelerator fully open at 2000 rpm: 15.6 mm3/st

·

Driving with the accelerator fully open at 3000 rpm: 43.8 mm3/st


Target Common Rail Pressure Target common rail pressure Target common rail pressure (ECU calculated value) Min.: 0 kPa, Max.: 250000 kPa 30000 to 200000 kPa when engine running
·

Inspect the (actual) fuel pressure, comparing it with the common rail target value.

·

Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions when idling after warm up the engine.


Fuel Press Fuel pressure Sensor output (fuel pressure sensor) Min.: 0 kPa, Max.: 250000 kPa Idling: 30000 to 50000 kPa
·

Fuel press is the actual common rail fuel pressure.

·

Inspect by comparing the fuel pressure with the target fuel pressure.

·

When in a stable condition such as when idling after warm up the engine, the fuel pressure is within +/-5000 kPa of the target fuel pressure.

·

The ECM uses fuel pressure for feedback control of the target fuel pressure via the fuel supply pump assembly.

The injection amount is determined based on the injection timing and fuel pressure.

Also, the spray pattern is selected based on the fuel pressure.

·

For startup, at least 25000 kPa of fuel pressure is needed (take care as there is a response lag when the pressure rises).

·

When the fuel pressure is below 25000 kPa, it may cause rough idling.

·

When the fuel pressure has decreased by 20000 kPa from the target fuel pressure, there may be a lack of power.

·

If actual fuel pressure is 5000 kPa higher than the target fuel pressure, P1229 will be stored. When the actual fuel pressure is lower than the target fuel pressure, "P1608 Lack of Power" may be detected depending on the degree of deviation from the target pressure.

·

When the fuel pressure is higher than 220000 kPa, DTC P0088 will be stored.


Cause of Out of Range:
·

Fuel supply pump assembly

·

High pressure pipes

·

Fuel pressure sensor

·

Injector assembly

·

Feed pump (fuel supply pump assembly)

·

Fuel filter element sub-assembly

·

Pressure discharge valve

·

Air in the fuel pipes

·

Lack of fuel


Results of real-vehicle check:
·

Ignition switch ON: 0 kPa

·

Cranking: 44100 kPa

·

Idling (warm up the engine): 34340 kPa (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 72340 kPa

·

Running without load (4000 rpm): 83500 kPa

·

Driving with the accelerator fully open at 2000 rpm: 143810 kPa

·

Driving with the accelerator fully open at 3000 rpm: 188780 kPa


Symptoms when out of range:
Difficult to start, poor driveability, lack of power, abnormal combustion noise
Common Rail Pres Sens 2 Fuel pressure Sensor output (fuel pressure sensor) Min.: 0 kPa, Max.: 250000 kPa Idling: 30000 to 50000 kPa This is a backup output value from the fuel pressure sensor.
Cause of Out of Range:
·

Fuel supply pump assembly

·

High pressure pipes

·

Fuel pressure sensor

·

Injector assembly

·

Feed pump (fuel supply pump assembly)

·

Fuel filter element sub-assembly

·

Pressure discharge valve

·

Air in the fuel pipes

·

Lack of fuel


Results of real-vehicle check:
·

Ignition switch ON: 0 kPa

·

Cranking: 43190 kPa

·

Idling (warm up the engine): 33430 kPa (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 71430 kPa

·

Running without load (4000 rpm): 82240 kPa

·

Driving with the accelerator fully open at 2000 rpm: 143250 kPa

·

Driving with the accelerator fully open at 3000 rpm: 187870 kPa


Symptoms when out of range:
Poor driveability, lack of power, abnormal combustion noise.
Fuel Temperature Fuel temperature Sensor output (fuel temperature sensor) Min.: -40°C, Max.: 140°C Actual fuel temperature After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature.
Fuel Return Temp Fuel return temperature - Min.: -40°C, Max.: 140°C Idling after engine warmed-up: 35 to 85°C (95 to 185°F) If the "Fuel Return Temp" value is not between 35°C (95°F) and 110°C (230°F), "Pilot Quantity Learning" is prohibited.
Target Pump SCV Current Final pump current target value Target value control (pump current) Min.: 0 mA, Max.: 4000 mA Idling: 923 to 1123 mA
·

ECU-calculated value for the suction control valve actuation target current.

·

Value is large when a high fuel pressure is desired.

·

Normally, the value is between 800 and 2500 mA.

·

If the value is stuck at 3000 mA or higher, it indicates that the operation is poor (poor movement due to deposits, etc.).

·

When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.


Cause of Out of Range:
·

Suction control valve malfunction

·

Clogged fuel filter element sub-assembly


Results of real-vehicle check:
·

Ignition switch ON: 1023.2 mA

·

Cranking: 1163.6 mA

·

Idling (warm up the engine): 1024.7 mA (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 1046.2 mA

·

Running without load (4000 rpm): 1075.5 mA

·

Driving with the accelerator fully open at 2000 rpm: 1241.1 mA

·

Driving with the accelerator fully open at 3000 rpm: 1397.2 mA


Symptoms when out of range:
Difficulty starting, lack of power or rough idling
Pump SCV Learning Value Pump SCV learning value Learned value Min.: -4096 mA, Max.: 4095.8 mA
·

Min.: -100 mA

·

Max.: 100 mA


If the value is stuck at 200 mA or higher or -200 mA or less, it indicates that the operation is poor (poor movement due to deposits, etc.).
Cause of Out of Range:
·

Suction control valve malfunction

·

Clogged fuel filter element sub-assembly


Results of real-vehicle check:
·

Ignition switch ON: 12.5 mA

·

Cranking: 10.7 mA

·

Idling (warm up the engine): 12.5 mA (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 7.5 mA

·

Running without load (4000 rpm): 7.5 mA

·

Driving with the accelerator fully open at 2000 rpm: 12.1 mA

·

Driving with the accelerator fully open at 3000 rpm: 12.1 mA


Symptoms when out of range:
Difficulty starting, lack of power or rough idling
Pressure Discharge Valve Pressure discharge valve operation - ON or OFF ON: Pressure discharge valve open This is the ECM command.
Idle Injection Volume (Min) Idle minimum injection volume - Min.: 0 mm3/st, Max.: 39.8 mm3/st - -

EGR System


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Target EGR Position EGR valve target opening amount ECU-calculated value based on sensors (mass air flow meter, manifold absolute pressure sensor, intake air temperature (built into mass air flow meter), etc.) Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 90%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Used for comparison to "Actual EGR Valve Pos.".


Results of real-vehicle check:
·

Ignition switch ON: 0%

·

Cranking: 0%

·

Idling (warm up the engine): 54.5%

·

Running without load (2500 rpm): 62.3%

·

Running without load (4000 rpm): 0%

·

Driving with the accelerator fully open at 2000 rpm: 0%

·

Driving with the accelerator fully open at 3000 rpm: 0%


Symptoms when out of range:
·

When value is out of range and approaching 0%: mass air flow meter degradation, intake or exhaust system blockage

·

When value is out of range and approaching 100%: EGR pipe blockage


Actual EGR Valve Pos. EGR valve position Calculated from EGR valve position sensor Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 92%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Inspect while comparing to "Target EGR Position".

·

Check the valve movement via the Active Test.

·

Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.


Symptoms when out of range:
·

EGR valve stuck open: Poor starts (engine does not stop), black smoke, white smoke, lack of power

·

EGR valve stuck closed: Increased turbo booster noise


EGR Close Lrn. Val. EGR fully closed position learned value EGR valve position sensor value when EGR valve fully closed Min.: 0 V, Max.: 5 V 0 to 1 V
·

This value is the EGR position sensor output voltage.

·

When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area.

·

As the lower and upper limits are 0 V and 1 V respectively, if the value becomes stuck at either of these values, there is a malfunction in the lift sensor or the valve position may be misaligned (foreign matter is present, etc.).


Results of real-vehicle check:
Ignition switch ON: 0.65 V
EGR Close Lrn. Status EGR valve fully closed position learning status - OK or NG OK
·

"OK" means the fully closed position learning has completed normally.

·

When NG, the learned fully closed position may be outside of the normal range.

When NG, there may be foreign matter stuck in the valve.


HINT:

After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed.


Results of real-vehicle check:
Ignition switch ON: OK
EGR Operation Prohibit EGR operation prohibition - OK or NG OK: Possible to perform "Control the EGR Step Position" and "Activate the EGR Valve Close" Active Tests
·

OK: It is possible to perform the "Control the EGR Step Position" and "Activate the EGR Valve Close" Active Tests.

·

NG: It is not possible to perform the "Control the EGR Step Position" and "Activate the EGR Valve Close" Active Tests.


EGR Cooler Bypass VSV Status of the EGR Cooler Bypass VSV - ON or OFF
·

ON: Vacuum switching valve (for EGR bypass valve) is ON

·

OFF: Vacuum switching valve (for EGR bypass valve) is OFF


·

When EGR Cooler Bypass VSV is ON, the value for EGR Cooler Bypass Position is Cooler and, when EGR Cooler Bypass VSV is OFF, the value for EGR Cooler Bypass Position is Bypass.

·

The EGR cooler bypass VSV is controlled by the ECM and the vacuum switching valve (for EGR bypass valve) is opened and closed by the vacuum created by the vacuum pump.


Cause of Out of Range:
·

Vacuum switching valve (for EGR bypass valve)

·

Vacuum switching valve (for EGR bypass valve) circuit


EGR Cooler Bypass Position Status of the EGR Cooler Bypass Position - Cooler or Bypass
·

Cooler: EGR Cooler Bypass VSV is "ON"

·

Bypass: EGR Cooler Bypass VSV is "OFF"


·

When EGR Cooler Bypass VSV is ON, the value for EGR Cooler Bypass Position is Cooler and, when EGR Cooler Bypass VSV is OFF, the value for EGR Cooler Bypass Position is Bypass.

·

The EGR cooler bypass VSV is controlled by the ECM and the vacuum switching valve (for EGR bypass valve) is opened and closed by the vacuum created by the vacuum pump.


Cause of Out of Range:
·

Vacuum switching valve (for EGR bypass valve)

·

Vacuum switching valve (for EGR bypass valve) circuit



Diesel Throttle System


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Target Throttle Position Target throttle position Value calculated by ECM Min.: -128%, Max.: 127%
·

Throttle valve fully opened: 0%

·

Throttle valve fully closed: 100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Actual Throttle Position Actual diesel throttle position - Min.: -20%, Max.: 120% Idling after engine warmed-up: 0 to 92% Closing percentage of the throttle valve.
·

Fully closed: 100%.

·

Fully open: 0%.

HINT:

There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).



Results of real-vehicle check:
·

Ignition switch ON: 0%

·

Cranking: 5%

·

Idling (warm up the engine): 87%

·

Running without load (2500 rpm): 61%

·

Running without load (4000 rpm): 0%

·

Driving with the accelerator fully open at 2000 rpm: 0%

·

Driving with the accelerator fully open at 3000 rpm: -1%


Symptoms when out of range:
·

Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle

·

Stuck open: Loud turbocharging sound, bad vibration when engine is stopped

·

When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h.


Throttle Close Learning Val. Throttle fully closed position learned value - Min.: 0 deg, Max.: 84 deg 14.25 to 21.25 deg
·

When the ignition switch is turned from ON to off and 5 seconds elapse, learning of "Throttle Close Learning Val." will be complete.

·

When "Throttle Close Learning Val." is outside of the normal range, a foreign object may lodged in the throttle valve.

·

If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present.

However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed.


Results of real-vehicle check:
Ignition switch ON: 17.9 deg
Diesel Throttle Learn Status Diesel throttle learning history - OK or NG OK
·

If the system is functioning properly, learning will be performed when the ignition switch is turned from ON to off.

·

NG indicates that a foreign object may be lodged in the throttle valve or actuator components, or a disconnection/short exists in the signal wires.


Results of real-vehicle check:
Ignition switch ON: OK
Throttle Sensor Volt % Absolute throttle position sensor Sensor output (throttle position sensor) Min.: 0%, Max.: 100%
·

Ignition switch ON: 60 to 80%

·

Warmed-up and idling: 10 to 80%


·

Throttle position sensor output voltage is converted using 5 V = 100%.

·

When fully closed: 14%.

·

When fully open: 70%.

·

When the ignition switch is turned from off to ON, the throttle valve fully opens once.

·

When the ignition switch is turned from ON to off, the throttle valve fully closes once.


Results of real-vehicle check:
·

Ignition switch ON: 70.5%

·

Cranking: 67.0%

·

Idling (warm up the engine): 21.5%

·

Running without load (2500 rpm): 36.0%

·

Running without load (4000 rpm): 70.1%

·

Driving with the accelerator fully open at 2000 rpm: 70.1%

·

Driving with the accelerator fully open at 3000 rpm: 70.5%


Symptoms when out of range:
·

Stuck closed: Engine stall, difficult to start, rough idling, lack of power, black smoke, white smoke

·

Stuck open: Loud turbocharging sound, bad vibration when engine is stopped

·

When the ECM detects a malfunction with the diesel throttle (MIL on), engine power is restricted but city driving is possible.


Throttle Motor DUTY Diesel throttle motor duty - Min.: 0%, Max.: 100% - When the moving force to open and close the diesel throttle valve increases, the value of the Throttle Motor Duty increases.
Results of real-vehicle check:
·

Cranking: 61.5%

·

Idling (warm up the engine): 58.8%

·

Running without load (2500 rpm): 38.8%

·

Running without load (4000 rpm): 61.5%

·

Driving with the accelerator fully open at 2000 rpm: 61.9%

·

Driving with the accelerator fully open at 3000 rpm: 62.7%



VN Turbo System


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Target Booster Pressure Target booster pressure Value calculated by ECM Min.: 0 kPa, Max.: 320 kPa Driving vehicle on level surface at 3000 rpm with full load: 200 to 225 kPa
·

Inspect while comparing with "MAP".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 sec. or more, a feeling of a lack of power will occur.

·

When the vehicle is driven with the engine speed at 3000 rpm or more and the accelerator pedal fully depressed, "MAP" is approximately equal to "Target Booster Pressure".


Boost Pressure Deviation Boost pressure deviation - Min.: -320 kPa, Max.: 320 kPa - Difference between target and actual boost pressure.
VN Turbo Error Level VN turbo driver opening angle level when abnormality detected - 0, 1, 2 or 3 0: Normal
·

3: Nearly fully closed (boost pressure and pre-turbine pressure are incredibly high and there is a risk of engine damage).

·

2: Roughly intermediate opening angle (not as bad as "3", but long-term usage is problematic).

·

1: Nearly fully open (will not cause engine damage, but at a low engine speed, turbocharging pressure will not rise and a lack of power will be felt).


VN Turbo Command VN turbo command value Controls the VN turbo vane opening position Min.: 0%, Max.: 100% 0 to 98%
·

"VN Turbo Command" is a command value.

·

0%: Vanes fully open (contraction of actuation rods)

·

90% or more: Vanes fully closed (extension of actuation rods)

·

When this value is large, the turbo works well.

·

There is no actual opening angle data to handle the VN turbo command value.


Results of real-vehicle check:
·

Ignition switch ON: 88%

·

Cranking: 68%

·

Idling (warm up the engine): 95%

·

Running without load (2500 rpm): 87%

·

Running without load (4000 rpm): 45%

·

Driving with the accelerator fully open at 2000 rpm: 67%

·

Driving with the accelerator fully open at 3000 rpm: 59%


Actual VN Position Actual VN turbo position - Min.: 0%, Max.: 127.5% 0 to 100% If the vanes do not move smoothly or become stuck, the difference between the actual value and the target value ("VN Turbo Command") becomes larger, and as a result, the motor duty also becomes larger.
Results of real-vehicle check:
·

Ignition switch ON: 100%

·

Cranking: 69.5%

·

Idling (warm up the engine): 95%

·

Running without load (2500 rpm): 87.5%

·

Running without load (4000 rpm): 45%

·

Driving with the accelerator fully open at 2000 rpm: 67.5%

·

Driving with the accelerator fully open at 3000 rpm: 59.5%


VN Position Sensor Out VN position sensor output voltage - Min.: 0 V, Max.: 5 V Idling after engine warmed-up: 1 to 3 V -
VN Motor Duty VN turbo motor duty - Min.: 0%, Max.: 127.5% 2 to 88% If the vanes do not move smoothly, the duty will increase towards 100%.
VN Close Learn Value VN turbo fully closed position learned value - Min.: 0 V, Max.: 5 V 1.5 to 2 V -
VN Close Learn Status VN turbo fully closed position learning status - OK or NG OK If learning is not complete, vehicle performance may decrease (power output is low).
VN Turbo Max Angle VN turbo maximum opening amount - Min.: 0%, Max.: 100% -
·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.


Results of real-vehicle check:
Ignition switch ON: 99.6%
VN Turbo Min Angle VN turbo minimum opening amount - Min.: 0%, Max.: 100% -
·

The minimum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.


Results of real-vehicle check:
Ignition switch ON: 39.8%
VN Turbo Operation Prohibit VN turbo operation prohibition - OK or NG OK: The "Test the Turbo Charger Step Motor" and "Activate the VN Turbo Open" Active Tests can be performed. When NG is displayed, the ECM does not permit "Test the Turbo Charger Step Motor" and "Activate the VN Turbo Open" Active Tests to be performed.

Exhaust control system


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
AF Lambda B1S1 Lambda equivalent ratio - Min.: 0, Max.: 255
·

AF Lambda B1S1 = air-fuel ratio / 14.5 (Stoichiometric A/F ratio)

·

Value less than 1 (0.000 to 0.999): Rich

·

Value more than 1 (1.001 to 255): Lean

·

Air-fuel ratio = intake air mass / (main fuel injection and exhaust fuel addition injection mass)


·

Check the air fuel ratio sensor output with the exhaust gas temperature (Exhaust Temperature B1S2) at 200°C (392°F) or higher (example: driving at speed of 50 km/h (31 mph) or more in 3rd gear).

·

If the exhaust fuel addition injector is clogged, the AF Lambda B1S1 value changes according to engine combustion, but large changes due to the addition of fuel are not seen even when PM forced regeneration is performed with the intelligent tester.

·

Furthermore, if the main injectors become clogged, the AF Lambda B1S1 value will increase under all circumstances while the engine is running (the value increases regardless of whether the PM forced regeneration has been performed).


Cause of Out of Range:
·

Air fuel ratio sensor

·

Air fuel ratio sensor circuit

·

Fuel injector assembly clogged


Results of real-vehicle check:
·

Idling (warm up the engine): 2.711

·

Running without load (2500 rpm): 3.057

·

Running without load (4000 rpm): 3.436

·

Driving with the accelerator fully open at 2000 rpm: 1.295

·

Driving with the accelerator fully open at 3000 rpm: 1.640


AFS Voltage B1S1 Air fuel ratio sensor output voltage - Min.: 0 V, Max.: 7.999 V -
·

Check the air fuel ratio sensor output with the exhaust gas temperature (Exhaust Temperature B1S2) at 200°C (392°F) or higher (example: driving at speed of 50 km/h (31 mph) or more in 3rd gear).

·

If the exhaust fuel addition injector is clogged, the AFS voltage B1S1 value changes according to engine combustion, but large changes due to the addition of fuel are not seen even when PM forced regeneration is performed with the intelligent tester.


Cause of Out of Range:
·

Air fuel ratio sensor

·

Air fuel ratio sensor circuit

·

Fuel injector assembly clogged


Results of real-vehicle check:
·

Idling (warm up the engine): 1.16 V

·

Running without load (2500 rpm): 1.23 V

·

Running without load (4000 rpm): 1.48 V

·

Driving with the accelerator fully open at 2000 rpm: 0.41 V

·

Driving with the accelerator fully open at 3000 rpm: 0.70 V


AFS Current B1S1 Air fuel ratio sensor current - Min.: -128 mA, Max.: 128 mA -
·

Check the air fuel ratio sensor output with the exhaust gas temperature (Exhaust Temperature B1S2) at 200°C (392°F) or higher (example: driving at speed of 50 km/h (31 mph) or more in 3rd gear).

·

If the exhaust fuel addition injector is clogged, even if PM forced regeneration is performed with the intelligent tester, the AFS voltage B1S1 value will not change.


Cause of Out of Range:
·

Air fuel ratio sensor

·

Air fuel ratio sensor circuit

·

Fuel injector assembly clogged


Results of real-vehicle check:
·

Idling (warm up the engine): 1.60 mA

·

Running without load (2500 rpm): 1.70 mA

·

Running without load (4000 rpm): 2.05 mA

·

Driving with the accelerator fully open at 2000 rpm: 0.55 mA

·

Driving with the accelerator fully open at 3000 rpm: 0.97 mA


AF Sensor Learning Value Air fuel ratio sensor learning value - Min.: 0 V, Max.: 5 V Value calculated by ECM Inspect the air fuel ratio sensor performance.
Results of real-vehicle check:
Ignition switch ON: 1.92 V
Exhaust Temperature B1S1 Supported Status of exhaust gas temperature Supported - Supp or Unsupp Supp If this item displays "Unsupp", a fixed value is displayed for "Exhaust Temperature", as exhaust gas temperature sensors are not equipped on the vehicle.
Exhaust Temperature B1S1 Exhaust gas temperature of CCo catalyst Sensor output (Exhaust gas temperature sensor B1S1) Min.: 0°C, Max.: 1000°C
·

Idling after engine warmed-up: 100 to 400°C (212 to 752°F)

·

During PM forced regeneration: 100 to 600°C (212 to 1112°F)


·

If an open occurs in an exhaust temperature sensor circuit, 0°C (32°F) is displayed on the intelligent tester.

·

If a short occurs in an exhaust temperature sensor circuit, 1000°C (1832°F) is displayed on the intelligent tester.


Cause of Out of Range:
·

Exhaust gas temperature sensor (B1S1)

·

DPF catalyst deteriorated


Exhaust Temperature B1S2 Supported Status of exhaust gas temperature Supported - Supp or Unsupp Supp If this item displays "Unsupp", a fixed value is displayed for "Exhaust Temperature", as exhaust gas temperature sensors are not equipped on the vehicle.
Exhaust Temperature B1S2 Exhaust gas temperature of DPF catalyst Sensor output (No. 2 exhaust gas temperature sensor B1S2) Min.: 0°C, Max.: 1000°C
·

Idling after engine warmed-up: 100 to 400°C (212 to 752°F)

·

During PM forced regeneration: 500 to 700°C (932 to 1292°F)


·

If an open occurs in an exhaust temperature sensor circuit, 0°C (32°F) is displayed on the intelligent tester.

·

If a short occurs in an exhaust temperature sensor circuit, 1000°C (1832°F) is displayed on the intelligent tester.


Cause of Out of Range:
·

No. 2 exhaust gas temperature sensor (B1S2)

·

DPF catalyst deteriorated


Exhaust Temperature B1S3 Supported Status of exhaust gas temperature Supported - Supp or Unsupp Supp If this item displays "Unsupp", a fixed value is displayed for "Exhaust Temperature", as exhaust gas temperature sensors are not equipped on the vehicle.
Exhaust Temperature B1S3 Exhaust gas temperature of DPF catalyst Sensor output (No. 3 exhaust gas temperature sensor B1S3) Min.: 0°C, Max.: 1000°C
·

Idling after engine warmed-up: 100 to 400°C (212 to 752°F)

·

During PM forced regeneration: 500 to 700°C (932 to 1292°F)


·

If an open occurs in an exhaust temperature sensor circuit, 0°C (32°F) is displayed on the intelligent tester.

·

If a short occurs in an exhaust temperature sensor circuit, 1000°C (1832°F) is displayed on the intelligent tester.


Cause of Out of Range:
·

No. 3 exhaust gas temperature sensor (B1S3)

·

DPF catalyst deteriorated


DPF Differential Pressure DPF differential pressure Sensor output (DPF differential pressure sensor) Min.: -5 kPa, Max.: 100 kPa Ignition switch ON:
Approximately 0 kPa
·

When PM (Particulate Matter) builds up in the DPF catalyst, the "DPF Differential Pressure" value increases.

·

At 3000 rpm (no load), if Catalyst Differential Press is 0.45 or more, the DPF catalyst has become blocked.


Cause of Out of Range:
·

DPF catalyst

·

DPF differential pressure sensor

·

Vacuum transmitting pipe clogged

·

Differential pressure sensor vacuum hose clogged


Results of real-vehicle check:
·

Ignition switch ON: 0.300 kPa

·

Cranking: 0.300 kPa

·

Idling (warm up the engine): -0.454 kPa

·

Running without load (2500 rpm): 1.675 kPa

·

Running without load (4000 rpm): 7.812 kPa

·

Driving with the accelerator fully open at 2000 rpm: 5.558 kPa

·

Driving with the accelerator fully open at 3000 rpm: 14.445 kPa


Catalyst Differential Press Amount of clogging in catalyst Calculated value Min.: -4, Max.: 3.9998 0.45 or less
·

Diagnosis is possible when the MAF reading is between 30 and 140 gm/s.

·

When the air intake volume is very low, such as when idling, due to excessive pressure fluctuation the correct values will not be displayed.

·

Catalyst Differential Press is the DPF Differential Pressure corrected in response to the MAF and other values.

·

If the filter in the DPF catalyst is clogged, the "Catalyst Differential Press" value increases.

·

When the difference in pressure exceeds approximately 0.45, DTC P244B is stored and "DPF PM Block" displays "Blocked".


Results of real-vehicle check:
·

Ignition switch ON: 0.0000

·

Cranking: -0.5261

·

Idling (warm up the engine): 0.0611

·

Running without load (2500 rpm): 0.0667

·

Running without load (4000 rpm): 0.0773

·

Driving with the accelerator fully open at 2000 rpm: 0.0720

·

Driving with the accelerator fully open at 3000 rpm: 0.0841


Symptoms when out of range:
·

If the difference in pressure increases, a decrease in engine power may be felt.

·

If an abnormal difference in pressure is detected, engine power is limited to protect the engine and catalyst.


Diff. Press. Sensor Corr. Differential pressure sensor 0 point learned value - Min.: -10 kPa, Max.: 245.9 kPa Ignition switch ON (engine stopped): - 1.5 to 1.5 kPa
·

This number indicates the correction value (0 point calibration) for compensation of variance in the differential pressure sensor.

·

If the value of DPF Differential Pressure does not approach 0 kPa when the ignition switch is ON (engine is stopped) and the Diff. Press. Sensor Corr. displays less than -1.5 kPa or more than 1.5 kPa, there may be a malfunction in the differential pressure sensor.

·

Note that the output of the differential pressure sensor fluctuates depending on the temperature.


Cause of Out of Range:
Differential pressure sensor
Exhaust Fuel Addition FB Exhaust fuel addition correction value Value calculated by ECM Min.: 0.8, Max.: 1.99 0.86 to 1.41
·

Usually Exhaust Fuel Addition FB is between 0.86 and 1.41.

·

Exhaust Fuel Addition FB is a correction value to increase the fuel volume injected from the exhaust fuel addition injector when the catalyst temperature does not rise to the target range during PM forced regeneration.

·

If the correction value is more than 1.45, a clog in the exhaust fuel addition injector assembly or fuel filter may be causing a reduction in injection volume or a problem with the engine (injectors, EGR, etc.) where the exhaust gas temperature decreases may be present. As a result, the catalyst temperature does not rise properly causing the catalyst to deteriorate.


Cause of Out of Range:
·

Exhaust fuel addition injector clogged

·

DPF catalyst deteriorated


Results of real-vehicle check:
Ignition switch ON: 1.03
DPF Thermal Deteriorate DPF catalyst thermal deteriorate Value calculated by ECM Normal or Deteriorated Normal
·

Exhaust fuel addition injector clogged

·

DPF catalyst deteriorated


DPF No Activate DPF operation Value calculated by ECM Activate or No Activate During PM forced regeneration: Activate If the exhaust gas temperature does not rise enough when the PM forced regeneration is performed, "No Activate" appears on the intelligent tester display. In this case, DPF catalyst deterioration and clogging of the exhaust fuel addition injector are possible causes of the malfunction. Other possible causes include EGR valve malfunction, exhaust temperature sensor malfunction, and injector malfunction.
Cause of Out of Range:
·

DPF catalyst

·

Exhaust fuel addition injector

·

No. 2 exhaust gas temperature sensor (B1S2)

·

No. 3 exhaust gas temperature sensor (B1S3)

·

Fuel injector assembly


Results of real-vehicle check:
Ignition switch ON: Activate
DPF PM Block DPF PM Block Calculated value No block or Blocked No Block
·

If PM (Particulate Matter) builds up in the DPF catalyst, the pressure differential from front to rear of the DPF catalyst gradually increases.

·

For example, at 3000 rpm (no load), if Catalyst Differential Press is 0.45 or more, "Blocked" appears on the intelligent tester display. In this case, clogging of the DPF catalyst, an injector system malfunction, differential pressure sensor system malfunction, exhaust leaks and a MAF meter malfunction are possible causes of the malfunction.

·

Clogging of the DPF catalyst may be caused by the use of an oil that does not meet the specifications, such as using an engine oil that is not low-ash.

·

Clogging of the DPF catalyst may also be caused by a high rate of engine oil consumption.


Cause of Out of Range:
·

DPF catalyst clogged

·

DPF differential pressure sensor

·

Vacuum transmitting pipe clogged

·

Differential pressure sensor vacuum hose clogged

·

Fuel injector assembly

·

Exhaust gas leak

·

MAF meter


Results of real-vehicle check:
Ignition switch ON: No Block
Catalyst Memory Error Catalyst memory error Calculated value No Error or Error No Error If the catalyst deterioration learning value from the old ECM is not input into the new ECM, or if a catalyst deterioration learning value that exceeds the setting range is input into the new ECM, DTC P062F is stored and "Catalyst Memory Error" displays "Error".
Symptoms when out of range:
Rough idling, poor driveability, black smoke, white smoke, combustion noise.
Add. INJ Flow Excessive Exhaust fuel addition injector injection volume excessive - Normal or Error Normal This item indicates whether there is an abnormal decrease in the actual air-fuel ratio.
DPF Overtemperature DPF catalyst overheat - Normal or Error Normal -
DPNR/DPF Status Reju(PM) PM forced regeneration status - Standby, Ready, Operate, Compl During PM forced regeneration: Operate The status is only displayed while performing "Activate the DPF Rejuvenate (PM)".
·

Standby

Before entering the "Activate the DPF Rejuvenate (PM)".


·

Ready

Enabling condition for "Activate the DPF Rejuvenate (PM)" is not met.


·

Operate

PM forced regeneration is being performed.

If "Activate the DPF Rejuvenate (PM)" does not finish completely, the status turns to "Ready".

If "Activate the DPF Rejuvenate (PM)" finishes completely, the status turns to "Compl".


·

Compl

PM forced regeneration is completed.



PM Accumulation Ratio PM accumulation ratio - Min.: 0%, Max.: 510% -
·

When PM forced regeneration is necessary, 100% is displayed for PM Accumulation Ratio.

·

If the ratio exceeds 100%, PM forced regeneration will be performed automatically


A258974
0.458,1.521 1.708,1.802 1.25,0.281 10 false AF Lambda B1S1 2.104,1.604 2.271,1.813 0.167,0.208 10 false 1 2.104,1.083 2.271,1.292 0.167,0.208 10 false 2 2.104,2.969 2.271,3.177 0.167,0.208 10 false 1 2.104,3.51 2.271,3.719 0.167,0.208 10 false 0 2.104,2.125 2.271,2.333 0.167,0.208 10 false 0 2.104,2.448 2.271,2.656 0.167,0.208 10 false 2 2.365,2.417 2.594,2.667 0.229,0.25 10 false (V) 2.99,3.708 3.24,3.958 0.25,0.25 10 false 10 3.302,3.792 3.656,4.042 0.354,0.25 10 false 14.5 3.76,3.708 4.01,3.958 0.25,0.25 10 false 20 4.521,3.708 4.771,3.958 0.25,0.25 10 false 30 5.292,3.708 5.542,3.958 0.25,0.25 10 false 40 6.063,3.708 6.313,3.958 0.25,0.25 10 false 50 0.052,0.01 2.313,0.188 2.26,0.177 10 false Air-Fuel Ratio Displayed on Tester: 3.75,4 4.688,4.198 0.938,0.198 10 false Air-Fuel Ratio 2.552,5.333 2.969,5.521 0.417,0.188 10 false 0.060 4.792,5.333 5.208,5.521 0.417,0.188 10 false 0.508 5.365,5.333 5.781,5.521 0.417,0.188 10 false 0.787 5.917,5.333 6.333,5.521 0.417,0.188 10 false 0.978 6.469,5.333 6.885,5.521 0.417,0.188 10 false 1.373 4.229,5.333 4.646,5.521 0.417,0.188 10 false 0.336 3.688,5.333 4.104,5.521 0.417,0.188 10 false 0.268 3.115,5.333 3.531,5.521 0.417,0.188 10 false 0.170 2.146,5.333 2.333,5.521 0.188,0.188 10 false 0 2.063,5.771 2.396,5.958 0.333,0.188 10 false 14.5 5.99,5.771 6.323,5.958 0.333,0.188 10 false 30 2.646,5.771 2.979,5.958 0.333,0.188 10 false 15 4.854,5.771 5.188,5.958 0.333,0.188 10 false 20 6.573,5.771 6.906,5.958 0.333,0.188 10 false 50 3.76,5.771 4.094,5.958 0.333,0.188 10 false 17 3.188,5.771 3.521,5.958 0.333,0.188 10 false 16 0.333,5.771 1.271,5.969 0.938,0.198 10 false Air-Fuel Ratio 4.302,5.771 4.635,5.958 0.333,0.188 10 false 18 5.427,5.771 5.76,5.958 0.333,0.188 10 false 25 4.188,1.729 6.813,2.042 2.625,0.313 10 false AF Lambda B1 S1 = Air-Fuel Ratio / 14.5 0.479,2.802 1.708,2.969 1.229,0.167 10 false AFS Voltage B1S1 1.104,5.26 1.333,5.458 0.229,0.198 10 false (V) 0.271,5.198 1.063,5.521 0.792,0.323 10 false AFS Voltage B1S1 0.281,4.667 1.083,5 0.802,0.333 10 false AF Lambda B1S1 2.104,4.813 2.333,4.979 0.229,0.167 10 false 1.0 2.573,4.813 2.917,4.99 0.344,0.177 10 false 1.03 3.135,4.813 3.448,5.01 0.313,0.198 10 false 1.10 3.667,4.813 3.979,4.958 0.313,0.146 10 false 1.17 4.26,4.813 4.552,5.01 0.292,0.198 10 false 1.24 4.792,4.813 5.104,4.958 0.313,0.146 10 false 1.38 5.375,4.813 5.708,4.969 0.333,0.156 10 false 1.72 5.927,4.813 6.219,4.958 0.292,0.146 10 false 2.07 6.521,4.813 6.844,4.969 0.323,0.156 10 false 3.45 0.344,6.156 0.74,6.344 0.396,0.188 10 false HINT: 0.615,6.479 5.74,6.708 5.125,0.229 10 false *1: AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V or less. 1.448,5.344 1.896,5.531 0.448,0.188 10 false -0.549 1.542,5.781 1.875,5.969 0.333,0.188 10 false 12 1.5,4.823 1.813,4.99 0.313,0.167 10 false 0.83 1.396,5.115 1.594,5.302 0.198,0.188 10 false *1 2.104,0.552 2.271,0.76 0.167,0.208 10 false 3


Diesel Starting


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Engine Speed (Starter Off) Engine speed when starter off - Min.: 0 rpm, Max.: 1594 rpm - Engine speed immediately after starting the engine.
Starter Count Starter on count - Min.: 0, Max.: 255 - Number of times the starter turned on from the time the ignition switch was turned to ON.
Run Dist of Previous Trip Distance driven during previous trip - Min.: 0 km, Max.: 261 km - Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:
·

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

·

If DTCs indicating insufficient power or problems with the DPF system, diesel throttle or EGR valve are stored, confirm this item in the freeze frame data of the stored DTCs to determine the distance driven when the DTCs were stored. The distance driven can be used as a reference when troubleshooting.



Glow Request Lighting Time Glow Request Lighting Time - Min.: 0 ms, Max.: 33423 ms -
·

By comparing Glow Request Lighting Time to IG-ON Time, the operation state (whether the engine was started, etc.) can be determined.

·

If the malfunction occurred when starting a cold engine at 0°C (32°F) or less, this item is useful in determining whether the engine was started after the glow plug indicator lights turned off.


IG-ON Time IG-ON Time - Min.: 0 ms, Max.: 33423 ms -
·

By comparing Glow Request Lighting Time to IG-ON Time, the operation state (whether the engine was started, etc.) can be determined.

·

If the malfunction occurred when starting a cold engine at 0°C (32°F) or less, this item is useful in determining whether the engine was started after the glow plug indicator lights turned off.


Immobiliser Fuel Cut History Immobiliser fuel cut history - ON or OFF OFF If Immobiliser Fuel Cut History was "ON" when DTC P1604 (Startability Malfunction) was stored, the engine could not be started due to the immobiliser.

Diesel Rough



Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
Rough Idle #1 Status of the Rough Idle #1 - ON or OFF OFF
·

This item indicates cylinders which had speeds lower than the other cylinders.

·

This item indicates cylinders which are likely to be the cause of rough idle.


Cause of Out of Range:
Injector assembly
Rough Idle #2 Status of the Rough Idle #2 - ON or OFF OFF
·

This item indicates cylinders which had speeds lower than the other cylinders.

·

This item indicates cylinders which are likely to be the cause of rough idle.


Cause of Out of Range:
Injector assembly
Rough Idle #3 Status of the Rough Idle #3 - ON or OFF OFF
·

This item indicates cylinders which had speeds lower than the other cylinders.

·

This item indicates cylinders which are likely to be the cause of rough idle.


Cause of Out of Range:
Injector assembly
Rough Idle #4 Status of the Rough Idle #4 - ON or OFF OFF
·

This item indicates cylinders which had speeds lower than the other cylinders.

·

This item indicates cylinders which are likely to be the cause of rough idle.


Cause of Out of Range:
Injector assembly
Electric Duty Feedback Value Electric load feedback value - Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 3.3 mm3/st Expected injection volume increase after the electrical load turns from off to on.
A/C Duty Feedback Value A/C load feedback value - Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 3.4 mm3/st Expected injection volume increase after the A/C turns from off to on.
PS Duty Feedback Value Power steering load feedback value - Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 mm3/st Expected injection volume increase after the power steering turns from off to on.

Diesel Power


Powertrain > Engine > Data List
Tester Display Measurement Item Type Range Normal Condition Diagnostic Note
MAF Low Mass air flow Low - ON or OFF OFF
·

When DTC P1608 is output, this item indicates whether the cause of lack of power is related to the intake air amount.

·

This item indicates whether the intake air amount measured by the mass air flow meter sub-assembly was insufficient, which would cause the fuel injection volume to be reduced for a certain period of time. If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored.

·

This item is "ON" when the intake air amount is low due to blockage in the intake system, disconnection of hoses or an excessive amount of EGR, and also when the intake air amount is measured to be low due to deterioration of the mass air flow meter sub-assembly.


Cause of Out of Range:
·

Mass air flow meter sub-assembly (value is out of range)

·

Intake system blockage

·

Disconnected air hoses (intake system)

·

EGR system (EGR valve closing malfunction)

·

Nozzle vane (turbo) movement problems


Symptoms when out of range:
Lack of power
Boost Pressure Low Status of the Boost Pressure Low - ON or OFF OFF
·

When DTC P1608 is output, this item indicates whether the cause of lack of power is due to the boost pressure.

·

This item indicates whether the actual boost pressure was insufficient compared to the target boost pressure, which would cause the fuel injection volume to be reduced for a certain period of time. If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored.


Cause of Out of Range:
·

Nozzle vane (turbo) stuck

·

Disconnected air hoses (intake system)

·

Manifold absolute pressure sensor

·

Atmospheric pressure sensor (built into ECM)

·

Difference between atmospheric pressure and intake pressure


Symptoms when out of range:
Lack of power
Common Rail Pressure Low Status of the Common Rail Pressure Low - ON or OFF OFF
·

When DTC P1608 is output, this item indicates whether the cause of lack of power is the common rail pressure.

·

This item indicates whether the actual common rail pressure was lower than the target pressure for a certain period of time. If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored.


Cause of Out of Range:
·

Suction control valve (movement problems)

·

Fuel leak

·

Fuel pressure sensor (built into common rail assembly)


Symptoms when out of range:
Lack of power
Engine Coolant Temp High Status of the Engine Coolant Temp High - ON or OFF OFF
·

When DTC P1608 is output, this item indicates whether the cause of lack of power is due to a high engine coolant temperature.

·

This item indicates whether the fuel injection volume was reduced for a certain period of time due to a high engine coolant temperature (overheating). If this is the case, this item displays "ON" and DTC P1608 (lack of engine power) is stored.


Cause of Out of Range:
·

Engine coolant temperature sensor

·

Engine coolant leak

·

Radiator clog


Symptoms when out of range:
Lack of power
MAF/Estimate MAF Ratio Ratio of intake air amount to estimated intake air amount - Min.: 0, Max.: 2.55 Engine speed 4000 rpm, EGR system off:
0.6 to 1.4
·

Even when the system is normal, the value may deviate from the range specified in Normal Condition for a short period of time (approximately 1 second).

·

This item indicates the ratio of the intake air amount to the estimated intake air amount. The estimated air amount is calculated using the intake manifold pressure and intake air temperature.

·

When DTC P1608 is stored, this item is useful in determining whether there is a problem in the turbocharger system or a disconnected or leaking pipe in the high pressure intake system when the boost pressure is insufficient.

·

When performing troubleshooting, this information is only valid when there is a high load (the diesel throttle is fully open) and the EGR system is off.


Cause of Out of Range:
·

Mass air flow meter sub-assembly

·

Turbocharger sub-assembly

·

Pipes between turbocharger sub-assembly and intake manifold are disconnected or leaking

·

Pipes between mass air flow meter sub-assembly and turbocharger sub-assembly are disconnected or leaking


Symptoms when out of range:
Lack of power

ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the VSV for Swirl Control Valve Activate the VSV for swirl control valve ON/OFF -
Control the A/C Cut Signal Control the A/C signal ON/OFF Confirm that the vehicle is stopped and the engine is idling
Connect the TC and TE1 Turn on the TC and TE1 connection ON/OFF -
Control the EGR Step Position Control the electric EGR control valve assembly 0 to 100% Test is possible when the following conditions are met:
·

Ignition switch ON.

·

Engine is stopped.


Activate the DPF Rejuvenate (PM) PM forced regeneration Raise temperature of DPF to more than 600°C (1112°F) by adding fuel intermittently using the exhaust fuel addition injector ON/OFF -
Diesel Throttle Target Angle Control the diesel throttle valve (bank 1) 0 to 90% Test is possible when the following conditions are met:
·

Ignition switch ON.

·

Engine is stopped.


Test the Turbo Charger Step Motor Activate the turbocharger 40 to 100% Test is possible when the following conditions are met:
·

Ignition switch ON.

·

Engine is stopped.


Test the Fuel Leak Pressurize the common rail interior and check for fuel leaks Stop/Start
·

Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when ON is selected

·

Above conditions preserved while test is ON


HINT:

If this Active Test is performed when the engine is cold, combustion may become unstable. However, this is not a malfunction. It is only necessary to confirm that the pressure rises to the target pressure and that there are no fuel leaks.


Activate the VN Turbo Open Activate the turbocharger ON/OFF Confirm that the engine is running.
Activate the EGR Valve Close Activate the electric EGR control valve assembly ON/OFF Confirm that the vehicle is stopped and the engine is idling
Activate the VSV for EGR Cooler Bypass Activate the vacuum switching valve assembly (for EGR cooler) Bypass/Half Pos/Cooler Test is possible when the following conditions are met:
·

Engine warmed up

·

Engine is idling

·

Shift lever in neutral


If performing the Active Test continuously, it must be finished within 5 minutes.
Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #4) injector fuel cut ON/OFF Fuel injection is stopped while the test is ON.
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning.


Check the Cylinder Compression Check the cylinder compression pressure* ON/OFF Fuel injection stops in all cylinders.


HINT:

*: When cranking the engine, the Active Test measures the speed of each cylinder. In this Active Test, the fuel of all cylinders is cut when the engine is cranked for approximately 10 seconds.


At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch to ON and turn the tester on.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4 and Av Engine Speed of All Cyl.


6.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, the "Check the Cylinder Compression" Active Test will start. Fuel injection for all cylinders is prohibited and the engine speed measurement of each cylinder enters standby mode.


7.

Crank the engine for about 10 seconds.

8.

Monitor the engine speed (Engine Speed of Cyl #1 to #4, Av Engine Speed of All Cyl) displayed on the tester.

HINT:

At first, the tester display will show the engine speed measurement of each cylinder to be extremely high. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.


NOTICE:
·

After the "Check the Cylinder Compression" Active Test is turned on, it will automatically turn off after 255 seconds.

·

When the "Check the Cylinder Compression" test is off and the engine is cranked, the engine will start.

·

If the "Check the Cylinder Compression" test needs to be performed after it is turned on and performed once, press "EXIT" to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.

·

Use a fully-charged battery.




SYSTEM CHECK


a.

Activate the Pressure Discharge Valve Check

HINT:
·

This is the procedure for troubleshooting fuel pressure control malfunctions and combustion problems.

·

Malfunctions can be determined by checking the fuel pressure when performing a fuel cut and operating the pressure discharge valve with the intelligent tester.

·

During "Pressure Discharge Valve Check", the intelligent tester measures the fuel pressure while the engine is running, after the engine is stopped, and after the pressure discharge valve operates.



i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.
A204072

Turn the tester on.

NOTICE:

Confirm the following conditions:

·

Engine is idling.

·

Vehicle is stopped.

·

Fuel pressure is not extremely high (below 100000 kPa).

·

Fuel pressure is not extremely low (higher than 26000 kPa).

·

Fuel pressure sensor is normal.

·

Battery voltage is higher than 8 V.



HINT:

When the common rail pressure is unstable, the fuel pressure may decrease to a level where the test cannot be performed. In this situation, wait until the common rail pressure meets the test condition, and then perform the test.



iv.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check.

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 61 2109

v.
A204067

Press "Next".


vi.
A204068

Press "Next" again to proceed.


vii.
A204069

Select the "Pressure Discharge Valve Check" type.

HINT:
·

"Close to Open Check" opens the pressure discharge valve after the engine stops.

·

"Always Closed Check" holds the pressure discharge valve closed during the check.




viii.

Press "Next".


ix.

Perform troubleshooting based on the measurement results.

A204070

HINT:
·

During "Close to Open Check", if there is no large change in fuel pressure when the pressure discharge valve is closed while the engine is running and after the engine is stopped, and if the value is 0 kPa when the pressure discharge valve is open, the system is normal.

·

Perform "Always Closed Check" if the value is not 0 kPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.

·

If the fuel temperature is high, perform "Pressure Discharge Valve Check" after the fuel has cooled to the outside air temperature.

·

If a large amount of fuel is leaking, the fuel pressure decreases when the engine is stopped. However, the condition of the pressure discharge valve can still be determined by comparing the measurement results of "Close to Open Check" and "Always Closed Check".


A303297
5.365,0.083 6.771,0.281 1.406,0.198 10 false Fuel Press Recorded 0.74,1.438 2.271,1.635 1.531,0.198 10 false Fuel Press 0.75,2.635 2.281,2.833 1.531,0.198 10 false (Always Closed Check) 2.719,1.833 3.167,2.031 0.448,0.198 10 false 0 kPa 0.75,2.49 2.281,2.688 1.531,0.198 10 false Fuel Press 0.76,1.594 2.292,1.792 1.531,0.198 10 false (Always Closed Check) 2.75,3.219 3.198,3.417 0.448,0.198 10 false 0 kPa 0.75,3.667 2.417,4.083 1.667,0.417 10 false Engine Speed 2.75,3.885 3.198,4.083 0.448,0.198 10 false 0 rpm 2.833,4.333 3.281,4.531 0.448,0.198 10 false On 2.833,4.667 3.135,4.865 0.302,0.198 10 false Off 0.5,4.49 2.26,4.74 1.76,0.25 10 false Fuel Cut Operation Signal 0.5,5.219 2.156,5.583 1.656,0.365 10 false Pressure Discharge Valve Operation Prohibition 2.833,5.167 3.135,5.365 0.302,0.198 10 false Off 2.833,5.469 3.281,5.667 0.448,0.198 10 false On 2.396,5.833 3.25,6.073 0.854,0.24 10 false Closed (on) 2.833,6.135 3.135,6.333 0.302,0.198 10 false Off 2.49,6.5 3.344,6.74 0.854,0.24 10 false Open (on) 2.427,6.802 3.281,7.042 0.854,0.24 10 false Closed (on) 2.833,7.083 3.135,7.281 0.302,0.198 10 false Off 2.875,7.438 5.542,7.688 2.667,0.25 10 false Pressure Discharge Valve Operation Start 0.115,5.917 2.385,6.406 2.271,0.49 10 false Pressure Discharge Valve Operation (Always Closed Check) 0.115,6.781 2.406,7.323 2.292,0.542 10 false Pressure Discharge Valve Operation (Close to Open Check)