Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P200C  Diesel Particulate Filter Over Temperature Bank 1  


DESCRIPTION

A248426
2.302,1.458 2.833,0.24 2.833,0.24 2.979,0.24 true 2.844,1.875 3.271,1.063 3.271,1.063 3.375,1.063 true 2.958,2.302 3.281,1.74 3.281,1.74 3.344,1.74 true 2.417,2.458 2.021,2.823 2.021,2.823 1.927,2.823 true 2.24,3.323 0.781,3.781 0.781,3.781 0.781,3.885 true 1.271,1.5 0.115,0.656 0.115,0.656 0.292,0.656 true 2.854,2.865 3.24,3.281 3.24,3.281 3.365,3.281 true 0.375,0.563 2.229,0.833 1.854,0.271 10 false Turbocharger Sub-assembly 0.208,2.135 1.073,2.354 0.865,0.219 10 false Exhaust Gas 3.031,0.177 6.063,0.427 3.031,0.25 10 false Exhaust Fuel Addition Injector Assembly 3.417,1.021 5.5,1.469 2.083,0.448 10 false Exhaust Gas Temperature Sensor (B1S1) 3.385,1.688 5.844,2.177 2.458,0.49 10 false No. 2 Exhaust Gas Temperature Sensor (B1S2) 3.417,3.219 5.875,3.708 2.458,0.49 10 false No. 3 Exhaust Gas Temperature Sensor (B1S3) 6.281,3.969 6.635,4.177 0.354,0.208 10 false ECM 0.427,2.729 2.042,2.969 1.615,0.24 10 false DPF Catalytic Converter 0.656,3.906 2.052,4.115 1.396,0.208 10 false Air Fuel Ratio Sensor

The exhaust fuel addition injector is mounted on the outlet of the turbocharger sub-assembly, and low pressure fuel is supplied to the injector by the feed pump in the supply pump. This injector adds fuel in response to a control signal from the ECM, in order to perform PM forced regeneration.

During PM forced regeneration, the exhaust fuel addition injector adds fuel to raise the DPF* catalyst temperature.

*: Diesel Particulate Filter

HINT:
·

For more information on the exhaust fuel addition injector and DPF, refer to the following procedures (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P200C is present, refer to the diagnostic trouble code (DTC) chart for Diesel Particulate Filter System (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P200C Diesel Particulate Filter Over Temperature Bank 1 DPF catalyst temperature becomes higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Front exhaust pipe assembly (DPF catalytic converter)


Sub Trouble Area
·

No. 2 exhaust gas temperature sensor (B1S2)

·

No. 3 exhaust gas temperature sensor (B1S3)

·

Air fuel ratio sensor

·

Mass air flow meter

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Suction control valve

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

HINT:
·

Due to fail-safe operation when other DTCs (that involve the engine power limit) are stored, PM forced regeneration may be prohibited.

This DTC or P20CF, P244B, P244C and P2463 may be stored due to the fact that PM forced regeneration is prohibited due to the fail-safe operation of other DTCs.

·

The air-fuel ratio and the exhaust gas temperature can be checked by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / AF Lambda B1S1, Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

·

Malfunctions in the engine itself may affect the DPF system control and cause storage of this DTC. For example, malfunctions in the injector assemblies that cause a large amount of smoke emission: These affect the exhaust fuel addition injector assembly operation. Blockages or leaks in the air intake system, or an EGR system malfunction such as EGR passage blockages: These malfunctions affect the DPF catalyst temperature control. Therefore, the engine condition itself should also be checked, in addition to the exhaust fuel addition injector assembly.



Related Data List
DTC No. Data List
P200C
·

MAF

·

MAP

·

Intake Air Temp (Turbo)

·

Target Booster Pressure

·

Atmosphere Pressure

·

Coolant Temp

·

Engine Speed

·

AFS Voltage B1S1

·

AF Lambda B1S1

·

DPF PM Block

·

DPF No Activate

·

Exhaust Fuel Addition FB

·

Exhaust Temperature B1S1

·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3

·

Catalyst Differential Press

·

Injection Feedback Val #1 to #4

·

Injection Volume



CONFIRMATION DRIVING PATTERN

P200C
DTC Detection Drive Pattern PM forced regeneration*
*: When P200C is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.

MONITOR DESCRIPTION

The ECM monitors DPF catalyst temperature. When the temperature becomes high due to uncombusted fuel, engine oil or thermal degradation to the DPF catalyst, the ECM illuminates the MIL.

A244058
3.896,1.177 3.24,0.667 false 3.24,0.667 3.073,0.667 false 0.104,0.083 1.542,0.396 1.438,0.313 10 false Malfunction Detection: 0.167,1.771 1.49,2.219 1.323,0.448 10 false Exhaust Temperature B1S2 or B1S3 3.896,0.625 4.771,0.896 0.875,0.271 10 false MIL Goes On 5.823,1.146 6.927,1.365 1.104,0.219 10 false P200C Threshold 2.469,0.583 3.094,0.802 0.625,0.219 10 false Abnormal 3.281,1.906 5.604,2.156 2.323,0.25 10 false Normal (500 to 700°C (302 to 572°F)) 5.646,1.76 6.177,1.969 0.531,0.208 10 false Normal

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA) (PROCEDURE 1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Record the stored DTC and freeze frame data.


Result:
Proceed to
NEXT



NEXT

2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Confirm "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" in the freeze frame data which was recorded in step 1 and determine which exhaust gas temperature sensor to replace.

Result:
Result Items to be Replaced
Exhaust Temperature B1S2 value is 850°C (1562°F) or more No. 2 exhaust gas temperature sensor (B1S2)
No. 3 exhaust gas temperature sensor (B1S3)
Exhaust Temperature B1S3 value is 850°C (1562°F) or more No. 3 exhaust gas temperature sensor (B1S3)



b.

If DTC P200C is output, the exhaust gas temperature sensors need to be replaced. However, make sure to perform all diagnostic procedures for DTC P200C before replacing the exhaust gas temperature sensors.

HINT:

If the exhaust gas temperature sensors are subjected to an abnormally high temperature, the internal resistance of the sensor increases. This causes incorrect temperature measurement.



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR BLACK SMOKE
3.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedure [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL INJECTION SYSTEM

NG

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY
4.REPLACE FRONT EXHAUST PIPE ASSEMBLY
a.

Even though it has been determined that the front exhaust pipe assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P200C before replacing it.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

5.CHECK FUEL INJECTION SYSTEM
5.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

6.CHECK INTAKE / EXHAUST SYSTEM
6.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

7.CHECK AFTER TREATMENT CONTROL SYSTEM
7.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

8.REPLACE MALFUNCTIONING PARTS
8.REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P200C.


a.

Replace the Front exhaust pipe assembly.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/ DPF)>REMOVAL


b.

Replace the No. 2 exhaust gas temperature sensor (B1S2).

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


c.

Replace the No. 3 exhaust gas temperature sensor (B1S3).

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61


Result:
Proceed to
NEXT



NEXT

END