Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G157-23 (BATT) - C164-6 (E1) | L - BR | Battery (for measuring the battery voltage and for the ECM memory) | Always | 11 to 14 V |
| G156-24 (IGSW) - C164-6 (E1) | B-O - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| G157-24 (+B) - C164-6 (E1) | B - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| G157-17 (+B2) - C164-6 (E1) | B-R - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| G156-11 (MREL) - C164-6 (E1) | W-G - BR | MAIN relay | Ignition switch ON | 11 to 14 V |
| G156-11 (MREL) - C164-6 (E1) | W-G - BR | MAIN relay | 30 seconds elapsed after ignition switch off | 0 to 1.5 V |
| G156-6 (VCPA) - G156-5 (EPA) | LG-R - BR-W | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| G156-4 (VCP2) - G156-3 (EPA2) | BR-R - BR-Y | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| G157-2 (VPA) - G156-5 (EPA) | W-L - BR-W | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
| G157-2 (VPA) - G156-5 (EPA) | W-L - BR-W | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal fully depressed | 2.6 to 4.5 V |
| G157-1 (VPA2) - G156-3 (EPA2) | GR-G - BR-Y | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 1.2 to 2.0 V |
| G157-1 (VPA2) - G156-3 (EPA2) | GR-G - BR-Y | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully depressed | 3.4 to 4.75 V |
| C167-13 (VG) - C167-14 (EVG) | W-R - B-W | Mass air flow meter | Idling | Pulse generation |
| C167-7 (THA) - C167-1 (ETHA) | Y-B - BR | Intake air temperature sensor (built into mass air flow meter) | Idling, intake air temperature at 20°C (68°F) | 0.5 to 3.4 V |
| C167-10 (THIA) - C167-4 (ETHI) | Y-G - BR | Intake air temperature sensor | Idling, intake air temperature at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C167-9 (THW) - C167-3 (ETHW) | R-L - BR | Engine coolant temperature sensor | Idling, engine coolant temperature at 80°C (176°F) | 0.2 to 1.0 V |
| G157-6 (STA) - C164-6 (E1) | L-Y - BR*1
B-Y - BR*2 |
Starter signal | Cranking | 6.0 V or higher |
| C166-21 (#1) - C164-6 (E1) | B-W - BR | No. 1 injector assembly | Idling | Pulse generation
(See waveform 2) |
| C166-22 (#2) - C164-6 (E1) | R - BR | No. 2 injector assembly | Idling | Pulse generation
(See waveform 2) |
| C166-23 (#3) - C164-6 (E1) | V - BR | No. 3 injector assembly | Idling | Pulse generation
(See waveform 2) |
| C166-24 (#4) - C164-6 (E1) | Y-R - BR | No. 4 injector assembly | Idling | Pulse generation
(See waveform 2) |
| C163-13 (G+) - C163-14 (G-) | Y - L | Camshaft position sensor | Idling | Pulse generation
(See waveform 5) |
| C163-7 (NE+) - C163-8 (NE-) | Y - L | Crankshaft position sensor | Idling | Pulse generation
(See waveform 5) |
| G157-8 (STP) - C164-6 (E1) | G-W - BR | Stop light switch assembly | Ignition switch ON, brake pedal depressed | 7.5 to 14 V |
| G157-8 (STP) - C164-6 (E1) | G-W - BR | Stop light switch assembly | Ignition switch ON, brake pedal released | 0 to 1.5 V |
| G157-9 (ST1-) - C164-6 (E1) | R-L - BR | Stop light switch assembly
(opposite to STP) |
Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| G157-9 (ST1-) - C164-6 (E1) | R-L - BR | Stop light switch assembly
(opposite to STP) |
Ignition switch ON, brake pedal released | 7.5 to 14 V |
| C163-16 (CLSW)*1 - C164-6 (E1) | G-W - BR | Clutch switch assembly | Ignition switch ON, clutch pedal released | 8.5 to 14 V |
| G156-23 (TC) - C164-6 (E1) | P-B - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| G157-19 (W) - C164-6 (E1) | R-B - BR | MIL | MIL illuminated | 0 to 3 V |
| G157-19 (W) - C164-6 (E1) | R-B - BR | MIL | MIL not illuminated | 11 to 14 V |
| G156-30 (SPD) - C164-6 (E1) | V-R - BR | Speed signal from combination meter assembly | Ignition switch ON, slowly wheel rotated | Pulse generation
(See waveform 9) |
| C167-18 (VCPM) - C167-6 (EPIM) | R-W - BR | Power source of manifold absolute pressure sensor | Ignition switch ON | 4.5 to 5.5 V |
| C167-12 (PIM) - C167-6 (EPIM) | L-B - BR | Manifold absolute pressure sensor | Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied | 0.1 to 0.7 V |
| C167-12 (PIM) - C167-6 (EPIM) | L-B - BR | Manifold absolute pressure sensor | Same as atmospheric pressure | 0.8 to 1.5 V |
| C167-12 (PIM) - C167-6 (EPIM) | L-B - BR | Manifold absolute pressure sensor | Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied | 1.6 to 2.3 V |
| G156-12 (IREL) - C164-6 (E1) | B-W - BR | EDU relay | Idling | 0 to 1.5 V |
| G157-18 (TACH) - C164-6 (E1) | B-W - BR | Engine speed | Idling | Pulse generation |
| C167-23 (ALT) - C164-6 (E1) | G - BR | Generator assembly (Alternator) duty ratio | Idling | Pulse generation |
| C163-23 (PCV+) - C163-12 (PCV-) | G-W - G-Y | Suction control valve | Idling | Pulse generation
(See waveform 1) |
| C166-20 (INJF) - C164-6 (E1) | P - BR | Injector driver | Idling | Pulse generation
(See waveform 3) |
| C166-19 (PRD) - C164-6 (E1) | GR - BR | Pressure discharge valve drive signal | Engine warmed up, engine racing | Pulse generation
(See waveform 4) |
| C167-24 (RLFF) - C164-6 (E1) | GR - BR | Pressure discharge valve confirmation signal | Engine warmed up, engine racing | Pulse generation
(See waveform 4) |
| C163-19 (IDLO) - C164-6 (E1) | G - BR | Injector Driver | Idling | 4.5 to 5.5 V |
| C166-18 (VIJ1) - C166-6 (EIJ1) | B - R | Power source of fuel pressure sensor (No. 1 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C166-12 (PIJ1) - C166-6 (EIJ1) | W - R | Fuel pressure sensor (No. 1 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C166-17 (VIJ2) - C166-5 (EIJ2) | Y - L | Power source of fuel pressure sensor (No. 2 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C166-11 (PIJ2) - C166-5 (EIJ2) | G - L | Fuel pressure sensor (No. 2 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C166-16 (VIJ3) - C166-4 (EIJ3) | B - W | Power source of fuel pressure sensor (No. 3 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C166-10 (PIJ3) - C166-4 (EIJ3) | R - W | Fuel pressure sensor (No. 3 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C166-15 (VIJ4) - C166-3 (EIJ4) | L - Y | Power source of fuel pressure sensor (No. 4 injector assembly) | Ignition switch ON | 4.5 to 5.5 V |
| C166-9 (PIJ4) - C166-3 (EIJ4) | G - Y | Fuel pressure sensor (No. 4 injector assembly) | Engine warmed up, engine idling | 1.4 to 1.7 V |
| C164-15 (M+) - C164-6 (E1) | W - BR | DC motor (turbocharger sub-assembly) | Idling | Pulse generation
(See waveform 6) |
| C164-14 (M-) - C164-6 (E1) | B - BR | DC motor (turbocharger sub-assembly) | Idling | Pulse generation
(See waveform 7) |
| C167-17 (VNVC) - C167-5 (VNE2) | W - L | Power source of nozzle vane position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C167-11 (VNA) - C167-5 (VNE2) | R - L | Nozzle vane position sensor | Ignition switch ON | 2.3 to 2.7 V |
| C166-14 (VCVL) - C166-2 (EVLU) | R-W - BR | Power source of throttle position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C166-8 (VLU) - C166-2 (EVLU) | B- BR | Throttle position sensor | Ignition switch ON, throttle valve
fully opened |
3.6 to 4.2 V |
| C166-8 (VLU) - C166-2 (EVLU) | B- BR | Throttle position sensor | Ignition switch ON, throttle valve
fully closed |
0.4 to 1.0 V |
| C163-17 (LUSL) - C164-6 (E1) | GR - BR | Diesel throttle duty signal | Engine warmed up, racing engine | Pulse generation
(See waveform 8) |
| C166-13 (VCEG) - C166-1 (EEGL) | R-W - BR | Power source of EGR valve position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C166-7 (EGRA) - C166-1 (EEGL) | R-Y - BR | EGR valve position sensor | Ignition switch ON | 0.6 to 1.4 V |
| C164-1 (EGM+) - C164-13 (ME01) | L - W-B | EGR valve duty signal | Engine warmed up, idling | Pulse generation |
| C164-2 (EGM-) - C164-13 (ME01) | Y - W-B | EGR valve duty signal | Engine warmed up, idling | Pulse generation |
| C164-9 (ECBV) - C164-6 (E1) | B-L - BR | Vacuum switching valve (for EGR bypass valve) | Vacuum switching valve assembly (for EGR bypass valve) on | 0 to 1.5 V |
| Vacuum switching valve assembly (for EGR bypass valve) off | 11 to 14 V | |||
| C164-7 (SCV) - C164-11 (E01) | LG - W-B | Vacuum switching valve (for No. 1 swirl control valve) | Idling | 0 to 1.5 V |
| Engine speed 2600 rpm or more | 11 to 14 V | |||
| C164-8 (SCV2) - C164-11 (E01) | W-L - W-B | Vacuum switching valve (for No. 2 swirl control valve) | Idling | 0 to 1.5 V |
| Engine speed 2600 rpm or more | 11 to 14 V | |||
| G156-10 (AC1) - C164-11 (E01) | Y - W-B | A/C signal | A/C switch on | 0 to 1.5 V |
| A/C switch off | 11 to 14 V | |||
| G156-13 (ACT) - C164-11 (E01) | R-L - W-B | A/C signal | Ignition switch ON | 11 to 14 V |
| A/C cut control on | 0 to 3 V | |||
| C163-26 (NSW)*2 - C164-11 (E01) | L-Y - W-B | Park/neutral position switch assembly | Ignition switch ON, shift lever in P or N | Below 3 V |
| Ignition switch ON, shift lever not in P or N | 11 to 14 V | |||
| C163-16 (D)*2 - C164-11 (E01) | G-Y - W-B | Park/neutral position switch assembly | Ignition switch ON, shift lever in D | 11 to 14 V |
| Ignition switch ON, shift lever not in D | Below 1 V | |||
| G156-36 (CANL) - C164-6 (E1) | W - BR | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 10) |
| G156-35 (CANH) - C164-6 (E1) | B - BR | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 11) |
| C163-18 (CAN-)*2 - C164-6 (E1) | P - BR | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 10) |
| C163-24 (CAN+)*2 - C164-6 (E1) | V - BR | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 11) |
| C167-22 (CINJ) - C164-6 (E1) | B - BR | INJ communication line | Engine warmed up, idling | Pulse generation
(See waveform 12) |
*1: for Manual Transaxle
*2: for Automatic Transaxle
WAVEFORM 1
| Item | Content |
|---|---|
| Terminal No. (Symbol) | C163-23 (PCV+) - C163-12 (PCV-) |
| Tool Setting | 10 V/DIV., 5 msec./DIV. |
| Condition | Idling or cranking with warm engine |
The waveform varies depending on suction control valve operation.
WAVEFORM 2
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (A) C166-21 (#1) - C164-6 (E1)
(B) C166-23 (#3) - C164-6 (E1) (C) C166-24 (#4) - C164-6 (E1) (D) C166-22 (#2) - C164-6 (E1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
WAVEFORM 3
| Item | Content |
|---|---|
| Terminal No. (Symbol) | C166-20 (INJF) - C164-6 (E1) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
WAVEFORM 4
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (a) C166-19 (PRD) - C164-6 (E1)
(b) C167-24 (RLFF) - C164-6 (E1) |
| Tool Setting | 2 V/DIV., 1 msec./DIV. |
| Condition | Engine warmed up, engine racing |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 5
| Item | Content |
|---|---|
| Terminal No. (Symbol) | (a) C163-7 (NE+) - C163-8 (NE-)
(b) C163-13 (G+) - C163-14 (G-) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the engine speed.
WAVEFORM 6
| Item | Content |
|---|---|
| Terminal No. (Symbol) | C164-15 (M+) - C164-6 (E1) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on turbocharger operation.
WAVEFORM 7
| Item | Content |
|---|---|
| Terminal No. (Symbol) | C164-14 (M-) - C164-6 (E1) |
| Tool Setting | 5 V/DIV., 50 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the turbocharger status.
WAVEFORM 8
| Item | Content |
|---|---|
| Terminal No. (Symbol) | C163-17 (LUSL) - C164-6 (E1) |
| Tool Setting | 1 V/DIV., 2 msec./DIV. |
| Condition | Racing with warm engine |
The waveform varies depending on throttle valve operation.
WAVEFORM 9
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G156-30 (SPD) - C164-6 (E1) |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Driving at vehicle speed of 40 km/h (25 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 10
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G156-36 (CANL) - C164-6 (E1)
C163-18 (CAN-) - C164-6 (E1) |
| Tool Setting | 1 V/DIV., 10 msec./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 11
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G156-35 (CANH) - C164-6 (E1)
C163-24 (CAN+) - C164-6 (E1) |
| Tool Setting | 1 V/DIV., 10 msec./DIV. |
| Condition | Engine stopped, ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 12
| Item | Content |
|---|---|
| Terminal No. (Symbol) | C167-22 (CINJ) - C164-6 (E1) |
| Tool Setting | 2 V/DIV., 10 msec./DIV. |
| Condition | Idling with warm engine |
The waveform is output every 250 msec.