Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM J

2TR-FBE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to terminal IGSW of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (MAIN relay) and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A262785
5.781,3.427 6.177,3.677 0.396,0.25 10 false E1 0.865,2.771 1.552,3.021 0.688,0.25 10 false BATT P/I 5.781,3.021 6.333,3.271 0.552,0.25 10 false MREL 2.698,2.781 3.063,2.99 0.365,0.208 10 false EFI 2.083,0.906 2.51,1.219 0.427,0.313 10 false AM2 0.979,1.177 1.458,1.448 0.479,0.271 10 false AM2 6.135,3.958 6.531,4.156 0.396,0.198 10 false ECM 5.781,2.615 6.177,2.865 0.396,0.25 10 false +B 5.781,0.875 6.344,1.167 0.563,0.292 10 false IGSW 1.927,0.906 2.125,1.146 0.198,0.24 10 false 5 3.76,1.177 4.198,1.51 0.438,0.333 10 false IGN 3.083,0.906 3.281,1.135 0.198,0.229 10 false 6 0.729,3.188 1.313,3.427 0.583,0.24 10 false Battery 2.635,3.667 3.875,3.969 1.24,0.302 10 false Integration Relay 1.781,1.521 3.427,1.76 1.646,0.24 10 false Ignition Switch Assembly 1.781,1.365 2.063,1.573 0.281,0.208 10 false G9 2.74,0.906 3.156,1.219 0.417,0.313 10 false IG2 4.198,2.427 4.385,2.646 0.188,0.219 10 false 4 4.177,2.615 4.51,2.833 0.333,0.219 10 false 1J 4.208,2.833 4.427,3.021 0.219,0.188 10 false 2 4.177,3.01 4.458,3.229 0.281,0.219 10 false 1J 1.938,2.823 2.115,3.052 0.177,0.229 10 false 3 1.906,3.01 2.167,3.24 0.26,0.229 10 false 1J 5.344,1.021 5.781,1.24 0.438,0.219 10 false G146 5.417,0.833 5.698,1.063 0.281,0.229 10 false 22 5.344,2.615 5.781,2.813 0.438,0.198 10 false G145 5.438,2.427 5.75,2.677 0.313,0.25 10 false 23 5.344,3.01 5.781,3.229 0.438,0.219 10 false G146 5.438,2.823 5.646,3 0.208,0.177 10 false 12 5.396,3.438 5.719,3.646 0.323,0.208 10 false C98 5.479,3.25 5.677,3.448 0.198,0.198 10 false 5 3.49,3.344 3.99,3.552 0.5,0.208 10 false MAIN 1.938,2.427 2.135,2.677 0.198,0.25 10 false 1 1.885,2.615 2.167,2.854 0.281,0.24 10 false 1H

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-5 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)

2.INSPECT ECM (IGSW VOLTAGE)
a.
A262769
0.458,0.24 0.875,0.479 0.417,0.24 0.906,1.542 0.802,0.938 false 0.104,0.052 0.406,0.292 0.302,0.24 10 false *a 0.5,0.281 0.979,0.563 0.479,0.281 10 false G146 0.958,1.49 1.854,1.76 0.896,0.271 10 false 22 (IGSW)
*a Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G146-22 (IGSW) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 INTEGRATION RELAY (MAIN)

NG

8.INSPECT IGNITION SWITCH ASSEMBLY
3.INSPECT NO. 1 INTEGRATION RELAY (MAIN)
a.

Inspect the No. 1 integration relay (MAIN).

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - ECM)

NG

REPLACE INTEGRATION RELAY (MAIN)

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - ECM)
a.

Remove the integration relay (MAIN relay) from the engine room relay block.


b.

Disconnect the integration relay connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1J-4 - G145-23 (+B) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1J-4 or G145-23 (+B) - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the integration relay connector.


g.

Reinstall the integration relay.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [MAIN] - ECM)

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - BATTERY)
a.

Remove the integration relay (MAIN relay) from the engine room relay block.


b.

Disconnect the integration relay connector.


c.

Disconnect the cable from the negative (-) battery terminal.


d.

Disconnect the cable from the positive (+) battery terminal.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1H-1 - Positive battery terminal Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1H-1 or Positive battery terminal - Body ground Always 10 kΩ or higher



f.

Reconnect the integration relay connector.


g.

Reinstall the integration relay.


h.

Reconnect the cable to the positive (+) battery terminal.


i.

Reconnect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [MAIN] - BATTERY)

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - BODY GROUND)
a.

Remove the integration relay (MAIN relay) from the engine room relay block.


b.

Disconnect the integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-3 - Body ground Always Below 1 Ω



d.

Reconnect the integration relay connector.


e.

Reinstall the integration relay.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [MAIN] - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN] - ECM)
a.

Disconnect the ECM connector.


b.

Remove the integration relay (MAIN relay) from the engine room relay block.


c.

Disconnect the integration relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1J-2 - G146-12 (MREL) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1J-2 or G146-12 (MREL) - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the integration relay connector.


g.

Reinstall the integration relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [MAIN] - ECM)

8.INSPECT IGNITION SWITCH ASSEMBLY
a.
B119736
1.302,1.698 1.688,1.344 true 2.354,1.729 1.99,1.344 true 0.625,0.135 0.854,0.365 0.229,0.229 10 false *a 1.146,1.729 1.542,1.979 0.396,0.25 10 false IG2 2.208,1.74 2.604,1.99 0.396,0.25 10 false AM2
*a Component without harness connected
(Ignition Switch Assembly)


Disconnect the ignition switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 6 (IG2) LOCK 10 kΩ or higher
5 (AM2) - 6 (IG2) ON Below 1 Ω



c.

Reconnect the ignition switch assembly connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G146-22 (IGSW) - G9-6 (IG2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G146-22 (IGSW) or G9-6 (IG2) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the ignition switch assembly connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G9-5 (AM2) - Positive battery terminal Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G9-5 (AM2) or Positive battery terminal - Body ground Always 10 kΩ or higher



e.

Reconnect the ignition switch assembly connector.


f.

Reconnect the cable to the positive (+) battery terminal.


g.

Reconnect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)