Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM U

2TR-FBE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A224896
0.591,0.444 0.976,0.675 0.385,0.231 0.601,0.489 0.964,0.67 0.363,0.182 10 G145 6.22,0.444 6.605,0.675 0.385,0.231 6.289,0.489 6.593,0.67 0.304,0.182 10 C98 5.165,0.444 5.55,0.675 0.385,0.231 5.235,0.489 5.539,0.67 0.304,0.182 10 C97 4.14,0.444 4.525,0.675 0.385,0.231 4.21,0.489 4.514,0.67 0.304,0.182 10 C96 3.079,0.444 3.464,0.675 0.385,0.231 3.148,0.489 3.452,0.67 0.304,0.182 10 C95 1.603,0.444 1.989,0.675 0.385,0.231 1.617,0.489 1.976,0.67 0.36,0.182 10 G146

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G145-17 (BATT) - C98-5 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
G145-22 (+BM) - C98-5 (E1) R-W - BR Power source of throttle actuator Always 11 to 14 V
G146-22 (IGSW) - C98-5 (E1) B-O - BR Ignition switch Ignition switch ON 11 to 14 V
G145-23 (+B) - C98-5 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
G146-12 (MREL) - C98-5 (E1) W-G - BR MAIN relay Ignition switch ON 11 to 14 V
C95-10 (VCTA) - C96-16 (E2) Y - BR Power source of sensor (specific voltage) Ignition switch ON 4.5 to 5.0 V
C95-3 (VTA1) - C95-9 (ETA) B-R - BR Throttle position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
C95-3 (VTA1) - C95-9 (ETA) B-R - BR Throttle position sensor (for engine control) Ignition switch ON, accelerator pedal fully depressed 3.2 to 4.8 V
C95-4 (VTA2) - C95-9 (ETA) LG - BR Throttle position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
C95-4 (VTA2) - C95-9 (ETA) LG - BR Throttle position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully depressed 4.6 to 5.0 V
G146-6 (VPA) - G146-2 (EPA) W-L - BR-W Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
G146-6 (VPA) - G146-2 (EPA) W-L - BR-W Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
G146-5 (VPA2) - G146-1 (EPA2) GR-G - BR-Y Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
G146-5 (VPA2) - G146-1 (EPA2) GR-G - BR-Y Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully depressed 3.4 to 5.0 V
G146-4 (VCPA) - C98-5 (E1) LG-R - BR Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.0 V
G146-3 (VCP2) - C98-5 (E1) BR-R - BR Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.0 V
C95-13 (VG) - C95-7 (E2G) L-W - L-R Mass air flow meter Idling, shift lever in P or N (for A/T) or neutral (for M/T), A/C switch off 0.5 to 3.0 V
C95-12 (THA) - C95-11 (ETHA) L-B - BR Intake air temperature sensor Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
C95-18 (THW) - C95-17 (ETHW) B - BR Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C98-6 (#10) - C98-11 (E01) L - W-B Fuel injector assembly Ignition switch ON 11 to 14 V
C98-7 (#20) - C98-11 (E01) G - W-B Fuel injector assembly Ignition switch ON 11 to 14 V
C98-8 (#30) - C98-11 (E01) R - W-B Fuel injector assembly Ignition switch ON 11 to 14 V
C98-9 (#40) - C98-11 (E01) W - W-B Fuel injector assembly Ignition switch ON 11 to 14 V
C98-6 (#10) - C98-11 (E01) L - W-B Fuel injector assembly Idling Pulse generation
(See waveform 1)
C98-7 (#20) - C98-11 (E01) G - W-B Fuel injector assembly Idling Pulse generation
(See waveform 1)
C98-8 (#30) - C98-11 (E01) R - W-B Fuel injector assembly Idling Pulse generation
(See waveform 1)
C98-9 (#40) - C98-11 (E01) W - W-B Fuel injector assembly Idling Pulse generation
(See waveform 1)
C98-1 (IGT1) - C98-5 (E1) R - BR Ignition coil assembly
(ignition signal)
Idling Pulse generation
(See waveform 2)
C98-2 (IGT2) - C98-5 (E1) R-L - BR Ignition coil assembly
(ignition signal)
Idling Pulse generation
(See waveform 2)
C98-3 (IGT3) - C98-5 (E1) G-B - BR Ignition coil assembly
(ignition signal)
Idling Pulse generation
(See waveform 2)
C98-4 (IGT4) - C98-5 (E1) G - BR Ignition coil assembly
(ignition signal)
Idling Pulse generation
(See waveform 2)
C98-10 (IGF1) - C98-5 (E1) G-R - BR Ignition coil assembly
(ignition confirmation signal)
Ignition switch ON 4.5 to 5.0 V
C98-10 (IGF1) - C98-5 (E1) G-R - BR Ignition coil assembly
(ignition confirmation signal)
Idling Pulse generation
(See waveform 2)
C96-11 (G2) - C96-5 (NE-) R - G Camshaft position sensor Idling Pulse generation
(See waveform 3)
C96-12 (NE+) - C96-5 (NE-) L - G Crankshaft position sensor Idling Pulse generation
(See waveform 3)
G146-25 (FC) - C98-5 (E1) LG-B - BR Fuel pump control Ignition switch ON 11 to 14 V
G146-25 (FC) - C98-5 (E1) LG-B - BR Fuel pump control Idling Below 1.5 V
G146-11 (FFR) - C98-5 (E1) L - BR Sub tank fuel pump control Ignition switch ON 11 to 14 V
G145-18 (DSSV) - C98-5 (E1) G - BR Sub tank solenoid valve assembly
(for fuel injection volume control)
FFV relay ON 11 to 14 V
G145-1 (SSV) - C98-5 (E1) Y - BR Sub tank fuel cut solenoid valve assembly
(for fuel cut control)
FFV relay ON 11 to 14 V
C98-14 (M+) - C98-13 (ME01) B - W-B Throttle actuator Idling with warm engine Pulse generation
(See waveform 4)
C98-15 (M-) - C98-13 (ME01) W - W-B Throttle actuator Idling with warm engine Pulse generation
(See waveform 5)
C97-7 (A1A+) - C98-5 (E1) B - BR Air fuel ratio sensor Ignition switch ON 3.3 V*1
C97-1 (A1A-) - C98-5 (E1) W - BR Air fuel ratio sensor Ignition switch ON 3.0 V*1
C97-13 (OX1B) - C96-16 (E2) B - BR Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 6)
C97-6 (HA1A) - C97-23 (E04) Y - W-B Air fuel ratio sensor Idling Pulse generation
(See waveform 7)
C97-6 (HA1A) - C97-23 (E04) Y - W-B Air fuel ratio sensor Ignition switch ON 11 to 14 V
C97-18 (HT1B) - C97-14 (EX1B) L-Y - B-R Heated oxygen sensor heater Idling Below 3.0 V
C97-18 (HT1B) - C97-14 (EX1B) L-Y - B-R Heated oxygen sensor heater Ignition switch ON 11 to 14 V
C95-6 (KNK1) - C95-5 (EKNK) B - W Knock sensor Maintain Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 8)
C96-14 (OC1+) - C96-9 (OC1-) P-L - Y Camshaft timing oil control valve assembly Idling Pulse generation
(See waveform 9)
C97-19 (PRG) - C98-5 (E1) L - BR Purge VSV Ignition switch ON 11 to 14 V
C97-19 (PRG) - C98-5 (E1) L - BR Purge VSV Idling Pulse generation
(See waveform 10)
G146-8 (STA) - C98-5 (E1) L-Y - BR
B-Y - BR*2
Starter signal Shift lever in N (for A/T) or neutral (M/T), ignition switch START 5.5 V or higher
G146-18 (STP) - C98-5 (E1) G-W - BR Stop light switch Brake pedal depressed 7.5 to 14 V
G146-18 (STP) - C98-5 (E1) G-W - BR Stop light switch Brake pedal released Below 1.5 V
G145-8 (ST1-) - C98-5 (E1) R-L - BR Stop light switch Ignition switch ON, brake pedal depressed Below 1.5 V
G145-8 (ST1-) - C98-5 (E1) R-L - BR Stop light switch Ignition switch ON, brake pedal released 7.5 to 14 V
G145-13 (W) - C98-5 (E1) R-B - BR MIL Idling 11 to 14 V
G145-13 (W) - C98-5 (E1) R-B - BR MIL Ignition switch ON Below 3.5 V
C95-19 (ALT) - C98-5 (E1) G - BR Generator Ignition switch ON 11 to 14 V
G145-5 (ELS) - C98-5 (E1) G - BR Electric load Taillight switch on 7.5 to 14 V
G145-5 (ELS) - C98-5 (E1) G - BR Electric load Taillight switch off Below 1.5 V
G145-10 (ELS3) - C98-5 (E1) B - BR Electric load Rear window defogger switch on 7.5 to 14 V
G145-10 (ELS3) - C98-5 (E1) B - BR Electric load Rear window defogger switch off Below 1.5 V
G146-29 (TACH) - C98-5 (E1) B-W - BR Engine speed Idling Pulse generation
(See waveform 11)
G146-16 (SPD) - C98-5 (E1) V-R - BR Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(See waveform 12)
G146-13 (TC) - C98-5 (E1) P-B - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
G145-3 (PSW) - C98-5 (E1) G-Y - BR Power steering oil pressure switch Steering wheel turning Below 1.5 V
G146-24 (NSW) - C98-5 (E1)*2 L-Y - BR Park/Neutral switch signal Ignition switch ON and shift lever in P or N Below 1 V
G146-24 (NSW) - C98-5 (E1)*2 L-Y - BR Park/Neutral switch signal Ignition switch ON and shift lever not in P or N 11 to 14 V
G146-34 (CANH) - C98-5 (E1) B - BR Signal for communication with other components Ignition switch ON Pulse generation
(See waveform 13)
G146-33 (CANL) - C98-5 (E1) W - BR Signal for communication with other components Ignition switch ON Pulse generation
(See waveform 14)
G145-6 (AIRV) - C98-5 (E1) V - BR Air switching valve for secondary air injection system Ignition switch ON 11 to 14 V
G145-19 (AIRP) - C98-5 (E1) W-L - BR Air pump control Ignition switch ON 11 to 14 V
G146-30 (AIDI) - C98-5 (E1) G-W - BR Diagnostic information signal for air injection system Air injection system operating Pulse generation
(See waveform 15)
C98-11 (E01) - Body ground W-B Ground Always Below 1 Ω
C98-12 (E02) - Body ground W-B Ground Always Below 1 Ω
C97-12 (E03) - Body ground W-B Ground Always Below 1 Ω
C97-23 (E04) - Body ground W-B Ground Always Below 1 Ω
C98-5 (E1) - Body ground BR Ground Always Below 1 Ω
C96-16 (E2) - Body ground BR Ground Always Below 1 Ω
G145-11 (EC) - Body ground R Ground Always Below 1 Ω
C98-13 (ME01) - Body ground W-B Ground Always Below 1 Ω
C97-24 (GE01) - Body ground BR Ground Always Below 1 Ω

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

*2: for Automatic Transmission

WAVEFORM 1


A303304
0.563,0.24 1.354,0.417 0.792,0.177 10 false 20 V/DIV. 0.646,1.573 1.438,1.75 0.792,0.177 10 false GND 1.813,1.906 2.813,2.177 1,0.271 10 false 20 msec./DIV.

Fuel injector

ECM Terminal Name Between #10 (to 40) and E01
Tester Range 20 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 2


A303306
0.604,0.229 1.292,0.469 0.688,0.24 10 false 2 V/DIV. 0.969,0.708 1.198,0.948 0.229,0.24 10 false (a) 0.49,0.906 1.177,1.146 0.688,0.24 10 false GND 0.5,1.469 1.188,1.708 0.688,0.24 10 false GND 0.979,1.281 1.208,1.521 0.229,0.24 10 false (b) 1.865,1.833 2.865,2.031 1,0.198 10 false 20 msec./DIV.

a.

Igniter IGT signal (from ECM to igniter)


b.

Igniter IGF signal (from igniter to ECM)

ECM Terminal Name (a) Between IGT (1 to 4) and E1
(b) Between IGF1 and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.




WAVEFORM 3


A063955
2.792,0.615 3.135,0.927 0.344,0.313 10 false GND 2.802,1.427 3.146,1.74 0.344,0.313 10 false GND 0.042,0.052 0.688,0.271 0.646,0.219 10 false 5 V/DIV. 0.271,0.583 0.469,0.771 0.198,0.188 10 false (a) 0.281,1.396 0.479,1.583 0.198,0.188 10 false (b) 1.625,1.927 2.542,2.177 0.917,0.25 10 false 20 msec./DIV.

a.

Camshaft position sensor


b.

Crankshaft position sensor

ECM Terminal Name (a) Between G2 and NE-
(b) Between NE+ and NE-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.




WAVEFORM 4


A208000
2.854,1 3.188,1.146 0.333,0.146 10 false GND 2.635,0.229 3.177,0.375 0.542,0.146 10 false 5 V/DIV. 0.5,0.615 0.719,0.76 0.219,0.146 10 false M+ 1.281,1.823 2.104,1.979 0.823,0.156 10 false 1 msec./DIV.

Throttle actuator positive terminal

ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 5


A245848
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.246,1.82 2.076,1.967 0.83,0.147 10 1 msec./DIV.

Throttle actuator negative terminal

ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 6


A303303
0.396,0.208 1.229,0.427 0.833,0.219 10 false 0.2 V/DIV. 0.583,1.458 1.052,1.635 0.469,0.177 10 false GND 1.781,1.875 2.823,2.083 1.042,0.208 10 false 200 msec./DIV.

Heated oxygen sensor

ECM Terminal Name Between OX1B and E2
Tester Range 0.2 V/DIV., 200 msec./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the DATA LIST, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.



WAVEFORM 7


A159460
2.813,1.823 3.219,2.042 0.406,0.219 10 false GND 0.083,0.594 0.667,0.771 0.583,0.177 10 false 5 V/DIV. 0.583,2.729 1.594,2.979 1.01,0.25 10 false 10 msec./DIV.

Air fuel ratio sensor heater

ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling with warm engine

HINT:

The wavelength varies in accordance with the engine operating condition.



WAVEFORM 8


A303309
2.406,0.521 3.104,0.719 0.698,0.198 10 false 1 V/DIV. 2.688,0.979 3.104,1.188 0.417,0.208 10 false GND 1,1.896 1.927,2.104 0.927,0.208 10 false 1 msec./DIV.

Knock sensor

ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 msec./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




WAVEFORM 9


A303302
0.458,0.26 1.208,0.458 0.75,0.198 10 false 5 V/DIV. 0.583,1.115 1.021,1.313 0.438,0.198 10 false GND 1.719,1.865 2.604,2.063 0.885,0.198 10 false 1 msec./DIV.

Camshaft timing oil control valve

ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling


WAVEFORM 10


A205411
2.604,0.281 3.229,0.438 0.625,0.156 10 false 10 V/DIV. 1.01,1.927 1.917,2.104 0.906,0.177 10 false 20 msec./DIV. 2.677,1.094 3.042,1.271 0.365,0.177 10 false GND

Purge VSV

ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A301908
0.438,0.281 1.094,0.51 0.656,0.229 10 false 5 V/DIV. 0.49,1.188 1.146,1.417 0.656,0.229 10 false GND 1.729,1.896 2.719,2.135 0.99,0.24 10 false 10 msec./DIV.

Engine speed signal

ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 12


A301907
0.469,0.281 1.375,0.5 0.906,0.219 10 false 5 V/DIV. 0.542,1.167 0.938,1.396 0.396,0.229 10 false GND 1.792,1.896 2.781,2.115 0.99,0.219 10 false 20 msec./DIV.

Vehicle speed signal

ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 13


A303346
0.125,0.333 1.021,0.531 0.896,0.198 10 false 1 V/DIV. 3,1.396 3.375,1.604 0.375,0.208 10 false GND 1.448,1.885 2.333,2.115 0.885,0.229 10 false 10 μs/DIV.

CAN communication signal (reference)

ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs/DIV.
Condition Ignition switch ON


WAVEFORM 14


A303347
0.135,0.292 1.365,0.49 1.229,0.198 10 false 1 V/DIV. 1.458,1.885 2.24,2.083 0.781,0.198 10 false 10 μs/DIV. 3.021,1.385 3.385,1.625 0.365,0.24 10 false GND

CAN communication signal (reference)

ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs/DIV.
Condition Ignition switch ON


WAVEFORM 15


G037721
2.927,1.313 3.26,1.615 0.333,0.302 10 false GND 2.667,0.073 3.271,0.271 0.604,0.198 10 false 5 V/DIV. 1.479,1.729 2.417,1.938 0.938,0.208 10 false 20 msec./DIV.

Terminal DI of air injection control driver

ECM Terminal Name Between AIDI and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Performing Active Test using intelligent tester (air injection system)

HINT:

The wavelength changes when the air injection control driver detects malfunctions in the air injection system.