Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The vehicle speed sensor outputs 4 pulses for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A112414
1.635,1.906 2.625,2.125 0.99,0.219 10 false Transmission 3.156,1.917 4.531,2.188 1.375,0.271 10 false Combination Meter 5.135,1.906 5.729,2.271 0.594,0.365 10 false ECM 2.469,0.427 3.625,0.688 1.156,0.26 10 false Pulse Signal 4.135,0.427 5.188,0.698 1.052,0.271 10 false Pulse Signal

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" for Automatic Transmission:
While the vehicle is being driven, no vehicle speed sensor signal is sent to the ECM (2 trip detection logic).
for Manual Transmission:
Conditions (a), (b) and (c) are met for 2000 seconds or more (2 trip detection logic):

(a) Vehicle is being driven.

(b) Fuel-cut operation is being performed.

(c) No speed signal is sent to the ECM.


for Manual Transmission:
Conditions (a), (b) and (c) are met for 2000 seconds or more (2 trip detection logic):

(a) Vehicle is being driven.

(b) Fuel-cut operation is being performed.

(c) No speed signal is sent to the ECM.


for Automatic Transmission:
·

Open or short in speed signal circuit

·

Combination meter

·

Speed Sensor

·

ECM


for Manual Transmission:
·

Open or short in speed signal circuit

·

Combination meter

·

Speed Sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A206532
6.281,0.615 6.625,0.802 0.344,0.188 10 false 5 V 5.521,0.885 5.958,1.073 0.438,0.188 10 false SPD 5.271,0.938 5.563,1.177 0.292,0.24 10 false 16 6.031,1.854 6.542,2.094 0.51,0.24 10 false G146 6.042,2.021 6.448,2.313 0.406,0.292 10 false ECM 4.354,1.052 4.677,1.271 0.323,0.219 10 false 2P 3.458,1.052 3.76,1.25 0.302,0.198 10 false 2Q 4.354,0.844 4.625,1.073 0.271,0.229 10 false 26 3.469,0.844 3.646,1 0.177,0.156 10 false 26 3.385,1.438 4.75,1.667 1.365,0.229 10 false Junction Connector 2.594,0.948 2.719,1.104 0.125,0.156 10 false 6 0.917,1.031 1.042,1.188 0.125,0.156 10 false 5 1.24,1.844 1.625,2.083 0.385,0.24 10 false G19 2.313,0.948 2.656,1.25 0.344,0.302 10 false +S 1.094,1.031 1.417,1.271 0.323,0.24 10 false SI 1.24,1.979 2.646,2.24 1.406,0.26 10 false Combination Meter 0.104,2.729 1.396,3.042 1.292,0.313 10 false from Speed Sensor

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

e.

Drive the vehicle.


f.

Read the value displayed on the intelligent tester.

OK:

Vehicle speeds displayed on intelligent tester and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-6 (+S) - G146-16 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (ECM - JUNCTION CONNECTOR)
a.

Disconnect the ECM connector.


b.

Disconnect the junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-26 - G146-16 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR IS DEFECTIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - JUNCTION CONNECTOR)