Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, the ECM then allows the current to flow to the throttle actuator so that it can be restarted after the ignition switch is turned off.

HINT:

This ETCS does not use a throttle cable.


A204005
0.229,1 0.938,1.5 0.708,0.5 10 false from MAIN Relay 2.115,1.979 2.688,2.271 0.573,0.292 10 false ETCS 0.104,1.823 0.906,2.01 0.802,0.188 10 false from Battery 0.823,3.563 1.865,3.74 1.042,0.177 10 false Throttle Actuator 5.479,4.229 5.948,4.469 0.469,0.24 10 false ECM 4.74,0.917 4.99,1.104 0.25,0.188 10 false +B 4.74,1.688 5.188,1.938 0.448,0.25 10 false +BM 4.74,2.427 5.083,2.677 0.344,0.25 10 false M+ 4.729,3.073 5.042,3.313 0.313,0.24 10 false M- 4.729,3.75 5.26,3.969 0.531,0.219 10 false ME01 5.917,0.771 6.396,1.427 0.479,0.656 10 false Power Source Circuit for CPU 5.938,2.333 6.542,2.979 0.604,0.646 10 false Throttle Actuator Control Circuit 1.531,2.469 1.823,2.74 0.292,0.271 10 false M+ 1.552,3.125 1.792,3.354 0.24,0.229 10 false M-

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2118 Throttle Actuator Control Motor Current Range / Performance An open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in electronic throttle control system power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM


Comes on DTC stored

FAIL-SAFE

When this DTC or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly. The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A262783
0.896,4.063 1.51,4.302 0.615,0.24 10 false Battery 2.896,1.146 3.406,1.375 0.51,0.229 10 false ETCS 2.74,2.24 3.042,2.49 0.302,0.25 10 false M+ 2.771,2.865 3.031,3.073 0.26,0.208 10 false M- 3.052,2.052 3.208,2.229 0.156,0.177 10 false 2 3.042,2.667 3.198,2.844 0.156,0.177 10 false 1 1.677,3.25 2.021,3.469 0.344,0.219 10 false C67 1.688,3.417 2.865,3.656 1.177,0.24 10 false Throttle Actuator 1.688,3.594 4.573,3.875 2.885,0.281 10 false (Built into Throttle Body with Motor Assembly) 3.979,3.104 4.635,3.323 0.656,0.219 10 false Shielded 6.115,5.125 6.594,5.385 0.479,0.26 10 false ECM 5.417,1 5.927,1.219 0.51,0.219 10 false G145 5.49,0.813 5.708,1.021 0.219,0.208 10 false 22 5.469,2.156 5.813,2.333 0.344,0.177 10 false C98 5.458,2.771 5.802,3.021 0.344,0.25 10 false C98 5.458,3.375 5.802,3.615 0.344,0.24 10 false C97 5.458,3.958 5.833,4.156 0.375,0.198 10 false C98 5.458,4.552 5.865,4.781 0.406,0.229 10 false C98 5.49,1.969 5.708,2.156 0.219,0.188 10 false 14 5.5,2.594 5.729,2.823 0.229,0.229 10 false 15 5.5,3.188 5.719,3.365 0.219,0.177 10 false 24 5.5,3.781 5.76,4.052 0.26,0.271 10 false 13 5.552,4.375 5.729,4.552 0.177,0.177 10 false 5 5.844,2.052 6.271,2.292 0.427,0.24 10 false M+ 5.833,2.667 6.115,2.896 0.281,0.229 10 false M- 5.833,0.875 6.521,1.219 0.688,0.344 10 false +BM 5.833,3.365 6.25,3.604 0.417,0.24 10 false GE01 5.833,3.844 6.302,4.083 0.469,0.24 10 false ME01 5.854,4.552 6.198,4.823 0.344,0.271 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / +BM Voltage.

Powertrain > Engine and ECT > Data List
Tester Display
+BM Voltage
50003 234 279

e.

Read the value displayed on the tester.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (+BM CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (+BM CIRCUIT)
a.

Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G145-22 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-13 (ME01) - Body ground Always Below 1 Ω
C98-5 (E1) - Body ground Always Below 1 Ω



d.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)