Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM D

2TR-FBE ENGINE CONTROL  SFI SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


A208456

When troubleshooting OBD II (On-Board Diagnostics) vehicles, the OBD scan tool (complying with ISO 15765-4) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle's ECM (Engine Control Module) can then be read.

OBD II regulations require that the vehicle's on-board computer illuminate the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:

a.

The emission control system components


b.

The powertrain control components which affect vehicle emissions


c.

The computer

In addition, the applicable DTCs prescribed by SAE J2012 are stored in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.

To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.

The DTCs and freeze frame data can be cleared using the scan tool (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).



NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used to increase the ability of the system to detect malfunctions, including intermittent malfunctions, when reproducing malfunction conditions (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next driving cycle, the MIL is illuminated (2nd trip).


FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


INSPECT BATTERY VOLTAGE


Battery voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


CHECK MIL


a.

Check that the MIL illuminates when the ignition switch is turned to ON.

If the MIL does not illuminate, there is a problem in the MIL circuit (See page ).

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>MIL Circuit


b.

Check that when the engine is started, the MIL turns off.



ALL READINESS


HINT:
·

With "All Readiness", it is possible to check whether or not the DTC judgment has been completed by using the intelligent tester.

·

Check "All Readiness" after reproducing malfunction conditions or for validation after finishing repairs.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Perform the DTC judgment driving pattern to run the DTC judgment.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

g.

Input the DTCs to be confirmed.


h.

Check the DTC judgment result.

DTC Judgment Result
Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit