Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM U

2TR-FBE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester ON.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed The speed indicated on the speedometer.
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 600 to 700 rpm: Idling -
Calculate Load Lode calculated by ECM Min.: 0%, Max.: 100%
·

10 to 30%: Idling

·

10 to 40%: Running without load (3000 rpm)


-
Vehicle Load Vehicle load Min.: 0%, Max.: 25700% Actual vehicle load -
MAF Air flow rate from MAF meter Min.: 0 gm/s, Max.: 655.35 gm/s 1.0 to 4.0 gm/s: Idling
10 to 11.5 gm/s: Running without load (3000 rpm)
If the value is approximately 0.0 gm/s:
·

The mass air flow meter power source circuit is open.

·

The VG circuit is open or shorted.


If the value is 271.0 gm/s or more:
·

The E2G circuit is open.


Atmosphere Pressure Atmospheric pressure Min.: 0 kPa, Max.: 255 kPa Equivalent to atmospheric pressure (absolute pressure) -
Coolant Temp Engine coolant temperature Min.: -40°C, Max.: 215°C 80 to 100°C (176 to 212°F): After warming up
·

If the value is -40°C (-40°F): the sensor circuit is open.

·

If the value is 140°C (284°F): the sensor circuit is shorted.


Intake Air Intake air temperature Min.: -40°C, Max.: 140°C Equivalent to ambient air temperature
·

If the value is -40°C (-40°F): the sensor circuit is open.

·

If the value is 140°C (284°F): the sensor circuit is shorted.


Engine Run Time Engine run time Min.: 0 s,
Max.: 65535 s
Time after engine start Service data.
Initial Engine Coolant Temp Initial engine coolant temperature Min.: -40°C, Max.: 119.3°C Engine coolant temperature when engine started Service data.
Initial Intake Air Temp Initial intake air temperature Min.: -40°C, Max.: 119.3°C Intake air temperature when engine started Service data.
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V: Idling -
Accelerator Position Absolute Accelerator Pedal Position Min.: 0%, Max.: 399.993% - -
Accel Sens. No.1 Volt % Absolute No. 1 accelerator pedal position Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal released

·

54 to 86%: Accelerator pedal fully depressed


-
Accel Sens. No.2 Volt % Absolute No. 2 accelerator pedal position Min.: 0%, Max.: 100%
·

12 to 42%: Accelerator pedal released

·

66 to 98%: Accelerator pedal fully depressed


-
Accel Sensor Out No.1 No. 1 accelerator pedal position sensor voltage Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal released

·

2.6 to 4.5 V: Accelerator pedal fully depressed


-
Accel Sensor Out No.2 No. 2 accelerator pedal position sensor voltage Min.: 0 V, Max.: 4.98 V
·

1.2 to 2.0 V: Accelerator pedal released

·

3.4 to 4.98 V: Accelerator pedal fully depressed


-
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle ON or OFF ON: Idling -
Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1 Min.: 0 deg, Max.: 124.5 deg - ETCS service data.
Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2 Min.: 0 deg, Max.: 124.5 deg - ETCS service data.
Throttle Sensor Volt % Throttle sensor positioning Min.: 0% Max.: 100%
·

10 to 22%: Accelerator pedal released

·

64 to 96%: Accelerator pedal fully depressed


A calculated value based on VTA1.
Throttl Sensor #2 Volt % Throttle sensor positioning #2 Min.: 0%, Max.: 100%
·

42 to 62%: Accelerator pedal released

·

92 to 100%: Accelerator pedal fully depressed


A calculated value based on VTA2.
ST1 Brake pedal signal ON or OFF ON: Brake pedal depressed -
System Guard System guard ON or OFF - ETCS service data.
Open Side Malfunction Open side malfunction ON or OFF - ETCS service data.
Throttle Idle Position Whether or not throttle position sensor detecting idle ON or OFF
·

ON: Accelerator pedal released

·

OFF: Accelerator pedal depressed


-
Throttle Require Position Required throttle position Min.: 0 V, Max.: 4.98 V 0.5 to 1.1 V: Idling -
Throttle Sensor Position Throttle sensor position* Min.: 0%, Max.: 100%
·

0%: Accelerator pedal released

·

50 to 80%: Accelerator pedal fully depressed


Value for the recognition of the throttle opening angle for the ECM.
HINT:

*: This excludes the throttle valve opening percentage due to Idle Speed Control (ISC).


Throttle Position No.1 No. 1 throttle position Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


-
Throttle Position No.2 No. 2 throttle position Min.: 0 V, Max.: 4.98 V
·

2.1 to 3.1 V: Accelerator pedal released

·

4.6 to 5.0 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


-
Throttle Position Command Throttle position command value Min.: 0 V, Max.: 4.980 V 0.5 to 4.8 V -
Throttle Sens Open Pos #1 Throttle position sensor No. 1 Min.: 0 V, Max.: 4.980 V 0.6 to 1.4 V ETCS service data.
Throttle Sens Open Pos #2 Throttle position sensor No. 2 Min.: 0 V, Max.: 4.980 V 1.7 to 2.5 V ETCS service data.
Throttle Motor Current Throttle actuator current Min.: 0 A, Max.: 19.9 A 0 to 3.0 A: Idling ETCS service data.
Throttle Motor DUTY Throttle actuator Min.: 0% Max.: 100% 10 to 22%: Idling after engine warmed up ETCS service data.
Throttle Motor Duty (Open) Throttle motor duty ratio (open) Min.: 0%, Max.: 255% 0 to 40%: Idling ETCS service data.
Throttle Motor Duty (Close) Throttle motor duty ratio (close) Min.: 0%, Max.: 255% 0 to 40%: Idling ETCS service data.
Throttle Fully Close Learn Throttle valve fully closed learned value Min.: 0 V, Max.: 4.98 V 0.4 to 1.0 V: Accelerator pedal released -
+BM Voltage +BM voltage Min.: 0, Max.: 79.998 V 11 to 14 V: Ignition switch ON and system normal ETCS service data.
Actuator Power Supply Actuator power supply ON or OFF
·

ON: Ignition switch ON and system normal

·

OFF: ETCS has failed


ETCS service data.
Throttle Position Throttle valve opening angle Min.: 0 deg, Max.: 499.99 deg - For use when engine stall, starting problems or rough idle is present.
ISC Flow Flow rate calculated using information from each sensor Min.: 0 L/s, Max.: 79.99 L/s - For use when engine stall, starting problems or rough idle is present.
ISC Position Requested opening amount calculated using ISC control Min.: 0 deg, Max.: 499.99 deg - For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value ISC feedback compensation amount Min.: -40 L/s, Max.: 39.99 L/s - For use when engine stall, starting problems or rough idle is present.
ISC Learning Value ISC learned compensation amount Min.: -40 L/s, Max.: 39.99 L/s - For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val Compensation flow rate according to electrical load Min.: -40 L/s, Max.: 39.99 L/s - For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val Compensation flow rate according to air conditioner load Min.: -40 L/s, Max.: 39.99 L/s - For use when engine stall, starting problems or rough idle is present.
PS Feedback Val Compensation flow rate according to power steering load Min.: -40 L/s, Max.: 39.99 L/s - For use when engine stall, starting problems or rough idle is present.
Low Revolution Control Low engine speed control operation state ON or OFF - For use when engine stall, starting problems or rough idle is present.
N Range Status Status of the N range status ON or OFF - For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow Intake air compensation flow rate Min.: -40 L/s, Max.: 39.99 L/s - For use when engine stall, starting problems or rough idle is present.
Sub Fuel Tank VSV VSV status for sub fuel tank ON or OFF ON: Sub fuel tank VSV on -
Injector (Port) Injection period of No. 1 cylinder Min.: 0 μs, Max.: 65535 μs 1800 to 3800 μs: Idling -
Injection Volum (Cylinder1) Injection volume (cylinder 1) Min.: 0 ml, Max.: 2.047 ml 0 to 0.5 ml: Idling The fuel injection volume for 10 injections.
Fuel Pump/Speed Status Fuel pump status ON or OFF - -
EVAP (Purge) VSV EVAP (Purge) VSV control duty Min.: 0%, Max.: 100% 0 to 100%: During idling A command signal from the ECM.
Evap Purge Flow Purge flow Min.: 0%, Max.: 399.9% 0 to 100%: Idling -
Purge Density Learn Value Purge density learned value Min.: -200, Max.: 199.993 -40 to 1: Idling Service data.
Fuel Pressure Relief Valve Fuel pressure relief valve status ON or OFF - -
EVAP Purge VSV VSV status for EVAP control ON or OFF - -
Purge Cut VSV Duty Purge cut VSV duty Min.: 0%, Max.: 399.9% - -
Target Air-Fuel Ratio Target air fuel ratio Min.: 0, Max.: 1.99 0.8 to 1.2: Idling -
AF Lambda B1S1 Output air fuel ratio associated with Bank 1 Sensor 1 Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich

·

Stoichiometric air-fuel ratio=1

·

Value more than 1 (1.001 to 1.999) = Lean


-
AFS Voltage B1S1 Air fuel ratio sensor output voltage Min.: 0 V, Max.: 7.99 V 3.0 to 3.5 V: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
AFS Current B1S1 Air fuel ratio sensor current Min.: -128 mA, Max.: 127.99 mA -0.5 to 0.5 mA: Idling Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
A/F Heater Duty #1 Air fuel ratio sensor heater duty ratio Min.: 0%, Max.: 399.9% 0 to 100% -
O2S B1S2 Heated oxygen sensor output voltage for bank 1 sensor 2 Min.: 0 V, Max.: 1.275 V 0 to 1.0 V: Driving at 70 km/h (44 mph) Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
O2 Heater B1S2 Heated oxygen sensor heater Active or Not Act - -
O2 Heater Curr Val B1S2 Heated oxygen sensor current Min.: 0 A, Max.: 4.9 A - -
Short FT #1 Short-term fuel trim of bank 1 Min.: -100%, Max.: 99.2% -20 to +20% Short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1 Long-term fuel trim of bank 1 Min.: -100%, Max.: 99.2% -20 to +20% The ECM will learn the Long FT values based on Short FT. The goal is to keep Short FT at 0% to keep the A/F mixture at the stoichiometric ratio. This value is used to determine whether the system related to air fuel ratio control is malfunctioning. The condition of the system is determined based on the sum of Short FT and Long FT (excluding times when the system is in transition).
·

+20% or more: There may be a lean air fuel ratio.

·

-20 to +20%: The air fuel ratio can be determined to be normal.

·

-20% or less: There may be a rich air fuel ratio.

·

The learned value is cleared when the battery cable is disconnected.

·

Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed * load), and separate value are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.


Total FT #1 Total fuel trim of bank 1 Min.: -0.5, Max.: 0.496 -0.2 to 0.2: Idling -
Fuel System Status #1 Fuel system status (Bank 1) OL or CL or OLDrive or OLFault or CLFault CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.

·

CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.

·

OLDrive: Open loop due to driving conditions (fuel enrichment).

·

OLFault: Open loop due to a detected system fault.

·

CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.


Fuel System Status #2 Fuel system status (Bank 2) OL or CL or OLDrive or OLFault or CLFault - -
Secondary Air Control VSV Secondary system status ON or OFF ON: Secondary air injection system operating -
2nd Air System Status Secondary air injection system status ON or OFF ON: Secondary air system operating -
AI Test Secondary air injection system operation prohibition READY or NOT RDY - -
IGN Advance Ignition timing advance for No. 1 cylinder Min.: -64 deg., Max.: 63.5 deg. BTDC 0 to 20°: Idling -
Knock Feedback Value Knocking feedback value Min.: -1024°CA, Max.: 1023.9°CA -20 to 0°CA
Driving, 70 km/h (44 mph)
Service data.
Knock Correct Learn Value Knocking correction learned value Min.: -1024°CA, Max.: 1023.9°CA 0 to 20°CA:
Driving, 70 km/h (44 mph)
Service data.
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1) Min.: 0° CA, Max.: 15.93° CA - For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2) Min.: 0° CA, Max.: 15.93° CA - For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3) Min.: 0° CA, Max.: 15.93° CA - For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4) Min.: 0° CA, Max.: 15.93° CA - For use when engine stall, starting problems or rough idle is present.
VVT Control Status #1 VVT control status ON or OFF - -
VVT Advance Fail VVT control failure status ON or OFF ON: VVT control failure -
VVT Aim Angle #1 VVT target angle Min.: 0%, Max.: 399.9% 0%: Idling The VVT duty signal value during the forced operation.
VVT Change Angle #1 VVT displacement angle Min.: 0 DegFR, Max.: 639.9 DegFR 0 to 5 DegFR: Idling The displacement angle during the forced operation.
VVT OCV Duty #1 VVT OCV operation duty Min.: 0%, Max.: 399.9% 0%: Idling The requested duty value for the forced operation.
VN Turbo Type VN turbo type Not Avl, Commo, Vacuum or CAN Com - -
Catalyst Temp B1S1 Catalyst temperature (Bank 1, Sensor 1) Min.: -40°C, Max.: 6513.5°C - -
Catalyst Temp B1S2 Catalyst temperature (Bank 1, Sensor 2) Min.: -40°C, Max.: 6513.5°C - -
Starter Signal Starter signal Open or Close Open: Cranking -
Power Steering Signal Power steering switch signal ON or OFF ON: Power steering operating -
Stop Light Switch Stop light switch ON or OFF ON: Brake pedal depressed -
A/C Signal A/C switch status ON or OFF ON: A/C on -
Closed Throttle Position SW Closed throttle position switch ON or OFF
·

ON: Throttle fully closed

·

OFF: Throttle open


-
Fuel Cut Condition Fuel cut condition ON or OFF ON: Fuel cut operating -
Immobiliser Communication Immobiliser communication ON or OFF ON: Normal -
Check Mode Check mode ON or OFF ON: Check mode on *
SPD Test Result Check mode result for vehicle speed sensor Compl or Incmpl - -
Misfire Test Result Check mode result for misfire monitor Compl or Incmpl - -
OXS1 Test Result Check mode result for heated oxygen sensor (Bank 1) Compl or Incmpl - -
A/F Test Results #1 Check mode result for air fuel ratio sensor (Bank 1) Compl or Incmpl - -
Complete Parts Monitor Comprehensive component monitor Not Avl or Avail - -
Fuel System Monitor Fuel system monitor Not Avl or Avail - -
Misfire Monitor Misfire monitor Not Avl or Avail - -
EGR/VVT Monitor EGR/VVT monitor Not Avl or Avail - -
EGR/VVT Monitor EGR/VVT monitor Compl or Incmpl - -
O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor Not Avl or Avail - -
O2S(A/FS) Heater Monitor O2S (A/FS) heater monitor Compl or Incmpl - -
O2S(A/FS) Monitor O2S (A/FS) heater monitor Not Avl or Avail - -
O2S(A/FS) Monitor O2S (A/FS) heater monitor Compl or Incmpl - -
A/C Monitor A/C monitor Not Avl or Avail - -
A/C Monitor A/C monitor Compl or Incmpl - -
2nd Air Monitor 2nd air monitor Not Avl or Avail - -
2nd Air Monitor 2nd air monitor Compl or Incmpl - -
EVAP Monitor EVAP monitor Not Avl or Avail - -
EVAP Monitor EVAP monitor Compl or Incmpl - -
Heated Catalyst Monitor Heated catalyst monitor Not Avl or Avail - -
Heated Catalyst Monitor Heated catalyst monitor Compl or Incmpl - -
Catalyst Monitor Catalyst monitor Not Avl or Avail - -
Catalyst Monitor Catalyst monitor Compl or Incmpl - -
TC Terminal TC terminal status ON or OFF - -
# Codes(Include History) Number of codes Min.: 0, Max.: 255 - Number of stored DTCs.
MIL MIL status ON or OFF ON: MIL on -
MIL ON Run Distance Distance driven after MIL turns on Min.: 0 km, Max.: 65535 km Distance driven after DTC stored -
Running Time from MIL ON Running time after MIL turned on Min.: 0 min,
Max.: 65535 min
Running time after MIL turned on -
Time after DTC Cleared Time after DTC cleared Min.: 0 min,
Max.: 65535 min
Time after DTCs cleared -
Distance from DTC Cleared Distance driven after DTC cleared Min.: 0 km, Max.: 65535 km Driving distance after DTCs cleared -
Warmup Cycle Cleared DTC Warmup cycles after DTC cleared Min.: 0, Max.: 255 - The number of warmup cycles after the DTCs were cleared.
Dist Batt Cable Disconnect Distance driven after battery cable disconnected Min.: 0 km, Max.: 65535 km Total distance vehicle driven after battery cable disconnected -
OBD Requirements OBD requirement - Brazil OBD Phase 2 -
Number of Emission DTC Emissions-related DTCs - - The number of emissions-related DTCs.
TC and TE1 TC and CG (TE1) terminals of DLC3 ON or OFF - -
Ignition Trig. Count Ignition counter Min.: 0, Max.: 65535 0 to 800 -
Cylinder #1 Misfire Count Misfire count of cylinder 1 Min.: 0, Max.: 255 0 -
Cylinder #2 Misfire Count Misfire count of cylinder 2 Min.: 0, Max.: 255 0 -
Cylinder #3 Misfire Count Misfire count of cylinder 3 Min.: 0, Max.: 255 0 -
Cylinder #4 Misfire Count Misfire count of cylinder 4 Min.: 0, Max.: 255 0 -
All Cylinders Misfire Count Misfire count of all cylinders Min.: 0, Max.: 255 0 to 35 -
Misfire RPM Engine speed for first misfire range Min.: 0 rpm, Max.: 6375 rpm 0 rpm: 0 misfires -
Misfire Load Engine load for first misfire range Min.: 0 g/rev, Max.: 3.98 g/rev 0 g/rev: 0 misfires -
Misfire Margin Misfire monitoring Min.: -128%, Max.: 127% -128 to 127% Misfire detecting margin.
Engine Speed (Starter Off) Engine speed when starter off Min.: 0 rpm, Max.: 51199 rpm - For use when engine stall, starting problems or rough idle is present.
Starter Count Number of times starter turned on after ignition switch turned to ON Min.: 0, Max.: 255 - For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip Distance driven during previous trip Min.: 0 km, Max.: 655.35 km - Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
HINT:

Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time Time elapsed after engine started (interval between ignition switch ON and off) Min.: 0 ms, Max.: 655350 ms - For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp Engine coolant temperature during previous trip Min.: -40°C, Max.: 215°C - For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp Intake air temperature during previous trip Min.: -40°C, Max.: 215°C - For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature Engine oil temperature (estimated temperature) Min.: -40°C, Max.: 215°C - For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp Engine oil temperature during previous trip Min.: -40°C, Max.: 215°C - For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C Ambient temperature for A/C Min.: -40°C, Max.: 215°C - For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp Ambient temperature during previous trip Min.: -40°C, Max.: 215°C - For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation History of hesitation during engine start ON or OFF - -
Low Rev for Eng Start History of low engine speed after engine start ON or OFF - -
Minimum Engine Speed Minimum engine speed Min.: 0 rpm, Max.: 51199 rpm - For use when engine stall, starting problems or rough idle is present.
A/F Learn Value Idle #1 Air fuel ratio learned value for idling Min.: -50%, Max.: 49.6% -20 to +20% Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).
A/F Learn Value Low #1 Air fuel ratio learned value for low engine loads Min.: -50%, Max.: 49.6% -20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1 Air fuel ratio learned value for mid-sized engine loads 1 Min.: -50%, Max.: 49.6% -20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1 Air fuel ratio learned value for mid-sized engine loads 2 Min.: -50%, Max.: 49.6% -20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1 Air fuel ratio learned value for high engine loads Min.: -50%, Max.: 49.6% -20 to +20% Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
ACT VSV A/C cut status for Active Test ON or OFF - Active Test support data.
Idle Fuel Cut Fuel cut at idle ON or OFF ON: Fuel cut operating Idle Fuel Cut is "ON" when the throttle valve fully is closed and the engine speed is over 2800 rpm.
FC TAU Fuel cut TAU (Fuel cut during very light load) ON or OFF ON: Fuel cut operating Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut Status of the immobiliser fuel cut ON or OFF - -
Immobiliser Fuel Cut History Status of the Immobiliser Fuel Cut History ON or OFF - -
Alcohol Feedback Value Alcohol feedback value Min.: 0%, Max.: 399.9% Depend on fuel alcohol value.
·

In case of E100, the value is 65%

·

In case of E22, the value is 8%


-
Alc FB Val bfr F/Crrctn by Stall Alcohol feedback value before fuel correction by stall Min.: 0%, Max.: 399.9% Depend on fuel alcohol value.
·

In case of E100, the value is 65%

·

In case of E22, the value is 8%


-
Trip aft F/Crrctn by Stall Trip after fuel correction by stall Min.: 0, Max.: 255 0 -
Fuel Dilution Estimate Fuel dilution estimate Min.: 0 ml, Max.: 1279.9 ml Less than 300 ml -
Electrical Load Signal 1 Electrical load signal ON or OFF - -
Electrical Load Signal 2 Electrical load signal ON or OFF - -
Model Code Model code - - Used for identifying model code: TGN###
Engine Type Engine type - - Used for identifying engine type: 2TRFBE
Cylinder Number Number of cylinders Min.: 0, Max.: 255 - Used for identifying number of cylinders: 4
Transmission Type Transmission type - - Used for identifying the transmission type: MT or ECT(4AT)
Destination Destination - - Used for identifying the destination:
W
Model Year Model year Min.: 1900, Max.: 2155 - Used for identifying the model year: 20##
System Identification System identification - - Used for identifying the engine system: Gasoline (gasoline engine)
Engine Speed of Cyl #1 Engine speed for cylinder 1 Min.: 0 rpm, Max.: 51199 rpm - Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #2 Engine speed for cylinder 2 Min.: 0 rpm, Max.: 51199 rpm - Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #3 Engine speed for cylinder 3 Min.: 0 rpm, Max.: 51199 rpm - Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #4 Engine speed for cylinder 4 Min.: 0 rpm, Max.: 51199 rpm - Output only when Check the Cylinder Compression is performed using the Active Test.
Av Engine Speed of All Cyl Engine speed for all cylinders Min.: 0 rpm, Max.: 51199 rpm - Output only when Check the Cylinder Compression is performed using the Active Test.
HINT:

*: Refer to Check Mode Procedure (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).




ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time.

Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester ON.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on tester, perform the "Active Test".

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Injection Volume Change injection volume Between -12% and 24.8%
·

All the injectors are tested at the same time.

·

Perform the test at less than 3000 rpm.

·

The injection volume can be changed in 1% gradations within the control range.


Control the Injection Volume for A/F Sensor Change injection volume -12.5%/0%/12.5%
·

Perform the test at less than 3000 rpm.

·

Control the Injection Volume for the A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs.

·

To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/ F Control System / AFS B1 S1 and O2S B1S2.


Activate the VSV for Secondary Air Control Activate secondary air system ON/OFF
·

Do not the perform test for 5 seconds or more.

·

After the test, do not perform the test again for 30 seconds.


Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
Control the A/C Cut Signal Control A/C cut signal ON/OFF -
Control the Fuel Pump / Speed Activate fuel pump (C/OPN relay) ON/OFF -
Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
Control the ETCS Open/Close Slow Speed Throttle actuator Close/Open
Open: Throttle valve opens slowly
This test is possible when the following conditions are met:
·

The ignition switch is ON.

·

The engine is stopped.

·

The accelerator pedal is fully depressed (accelerator pedal sensor: 58 degrees or more).

·

The shift lever is in P.


Control the ETCS Open/Close Fast Speed Throttle actuator Close/Open
Open: Throttle valve opens quickly
Same as above.
Control the VVT Linear (Bank1) Control Variable Valve Timing (VVT) -128 to 127%
OCV control duty ratio can be set to any value within this range
100%: Maximum advance
-100%: Maximum retard
·

The engine stalls or idles roughly when the VVT actuator is operated by 100%.

·

The test is possible during idle.


Control the VVT System (Bank1) Turn Oil Control Valve (OCV) on and off ON/OFF
·

The engine stalls or idles roughly when the OCV is turned on.

·

The engine runs and idles normally when the OCV is off.


Control the Cylinder Fuel Cut Cylinder #1 to #4 injector fuel cut ON/OFF The test is possible while the vehicle is stopped and the engine is idling.
Control the All Cylinders Fuel Cut All cylinder injector fuel cut ON/OFF The test is possible while the vehicle is stopped and the engine is idling.
Check the Cylinder Compression Check the cylinder compression pressure*1 ON/OFF The fuel injection and ignition stops in all cylinders.
Sub Fuel Tank VSV Activate sub fuel tank VSVs and fuel pump (for fuel sub tank) ON/OFF
·

Test is possible with the engine stopped.

·

Test is possible only once because the engine may be damaged if sub tank fuel flows into the cylinders.


HINT:

*1: When cranking the engine, each cylinder measures the engine speed.

In this Active Test, the fuel and ignition of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the tester on.

6.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:
·

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

·

Push the Function button and then select Snapshot Configuration to set the Trigger Point to zero.

·

Set the Record Time to 30 seconds.



7.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


8.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.


9.

Fully open the throttle.

10.

Crank the engine for about 10 seconds.

HINT:

Continue to crank the engine until the values change from the default value (51199 rpm).


11.

Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the tester.

NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If Check the Cylinder Compression needs to be performed after it is turned ON and performed once, press Exit button to return to the Active Test menu screen. Then perform Check the Cylinder Compression again.

·

Use a fully-charged battery.



HINT:

At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.


12.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.


13.

Push the snapshot button to turn the snapshot function off.

14.

Enter the following menus: Function / Snapshot Review / Engine and ECT / Snapshot File Manager, select the recorded data and display the data.

HINT:

If the data is not displayed, the change of the values cannot be observed.


15.

Check the change in engine speed values.

HINT:

As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.





SYSTEM CHECK


HINT:

Performing a system check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs (Pending Codes) are stored, and can detect potential malfunctions in the system. The system check can be performed with the intelligent tester.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility.


d.

Perform the system check by referring to the table below.



Tester Display Test Part Control Range Diagnostic Notes
Secondary Air Injection Check
(Automatic Mode)
Perform secondary air injection system operation automatically -
·

With a warm engine, make sure to turn the ignition switch off once.

·

If there are no pending DTCs after performing this test, the system is functioning normally.

·

Refer to the inspection procedure for secondary air injection system DTCs.

·

When performing the Secondary Air Injection Check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the system check is finished.


Secondary Air Injection Check
(Manual Mode)
Perform secondary air injection system operation manually Select monitor item 1, 2 or 3
1.

Air pump: ON

Air switching valve: OPEN

2.

Air pump: OFF

Air switching valve: CLOSE

3.

Air pump: ON

Air switching valve: CLOSE


-
·

With a warm engine, make sure to turn the ignition switch off once.

·

Used to detect malfunctioning parts.

·

Refer to the inspection procedure for secondary air injection system DTCs.

·

When performing the Secondary Air Injection Check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the system check is finished.