This DTC is stored if the engine stalls because of reasons other than ignition switch operation after the engine has started.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
It is necessary to check if the vehicle has run out of fuel before starting diagnosis because this DTC is also stored due to running out of fuel.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1603 | Engine Stall History | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, the engine stops for 0.5 seconds or more (the engine speed drops to 200 rpm or less) without the ignition switch being operated
(1 trip detection logic) |
·
Intake system connection ·
Purge VSV ·
Brake booster ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Wire harness or connector ·
Air fuel ratio sensor (sensor 1) ·
Power source circuit (purge VSV, fuel injector assembly, ignition coil assembly) ·
Fuel pump (for fuel main tank) ·
Fuel pump control circuit ·
Fuel line ·
Throttle body with motor assembly ·
Camshaft timing oil control valve assembly ·
Knock control sensor ·
Air conditioner system ·
Power steering system ·
Electrical load signal circuit ·
A/T system ·
Park/neutral position switch circuit ·
Sub tank fuel pump control circuit ·
Fuel pump (for fuel sub tank) ·
Fuel jet ·
Solenoid valve assembly (for fuel injection volume control) ·
Solenoid valve assembly (for fuel cut control) ·
ECM |
Does not come on | DTC stored |
In contrast to normal malfunction diagnosis for components, circuit and systems, DTC P1603 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
As this DTC can be stored as a result of certain user actions, even if this DTC is output, if the customer makes no mention of problems, clear this DTC without performing any troubleshooting and return the vehicle to the customer.
If any DTCs other than P1603 and/or P1605 are output, troubleshoot those DTCs first.
Since DTC P1603 is different from other DTCs, the following procedure is shown as a reference.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P1603 and/or P1605 is output | A |
| DTC P1603 and/or P1605 and other DTCs are output | B |
If any DTCs other than P1603 and/or P1605 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Check the following freeze frame data to see if the engine was cold or warm when the freeze frame data was recorded.
| Coolant Temp |
| Initial Engine Coolant Temp |
| Initial Intake Air Temp |
| Engine Run Time |
Check the following freeze frame data to see if the vehicle was idling, cruising, decelerating, accelerating, starting off, or stopped.
| Engine Speed |
| Vehicle Speed |
| Throttle Sensor Position |
| Throttl Sensor #2 Volt % |
| Accel Sens. No. 1 Volt % |
| Accel Sens. No. 2 Volt % |
| Neutral Position SW Signal |
| Stop Light Switch |
| Closed Throttle Position SW |
| Throttle Sensor Position |
Check the following freeze frame data to see the gear and lock-up state recorded when the engine stalled.
| Shift Status |
| Lock Up |
Check the following freeze frame data to see the engine load and electrical load when the freeze frame data was recorded.
| Calculate Load |
| Electrical Load Signal |
| A/C Signal |
| Power Steering Signal |
Check the following freeze frame data to see the purge VSV operation status when the freeze frame data was recorded.
| EVAP (Purge) VSV |
Check the following freeze frame data to see information related to engine idling from when the freeze frame data was recorded.
| Shift SW Status (P Range) |
| Shift SW Status (N Range) |
Check the following freeze frame data to see the air fuel ratio recorded when the engine stalled.
| Short FT #1 |
| Long FT #1 |
| AF Lambda B1S1 |
Check the following freeze frame data to see the ignition timing recorded when the engine stalled.
| IGN Advance |
| Knock Correct Learn Value |
Check the following freeze frame data to see the FFV (Flexible Fuel Vehicle) information recorded when the engine stalled.
| Alcohol Feedback Value |
| Alc FB Val bfr F/Crrctn by Stall |
| Trip aft F/Crrctn by Stall |
| Fuel Dilution Estimate |
Use this information to perform a simulation test.
Compare the "Normal Condition" in the Data List (reference values) with the freeze frame data listed above and with the simulation test results to determine the problem cause.
| Result | Proceed to |
|---|---|
| The problem cause can be determined | A |
| The problem cause cannot be determined | B |
A
B