Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0418  Secondary Air Injection System Control "A" Circuit  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0418 Secondary Air Injection System Control "A" Circuit Condition 1:

After a cold engine start, all conditions are met (2 trip detection logic):

1.

Secondary Air injection (AIR) system is not operating (air pump off, air switching valve off).

2.

Diagnostic signal from the air injection control driver is 20%.

3.

Battery voltage is 8 V or higher.



Condition 2:

After a cold engine start, all conditions are met (2 trip detection logic):

1.

Secondary Air injection (AIR) system is operating (air pump on, air switching valve on).

2.

Diagnostic signal from the air injection control driver is 20%.

3.

Battery voltage is 8 V or higher.



Condition 1:
·

Open in air pump drive circuit (air injection control driver - air pump assembly) or short between air pump drive circuit and +B or BATT

·

Open in air injection control driver BATT circuit (air injection control driver power source)

·

Harness and connector (air injection control driver - air pump assembly)

·

Air pump assembly

·

Air injection control driver

·

ECM


Condition 2:
·

Short between air pump drive circuit and body ground

·

Open or in air injection control driver BATT circuit (air injection control driver power source)

·

Harness and connector (air injection control driver - air pump assembly)

·

Air pump assembly

·

Air injection control driver

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The air injection control driver detects open and short circuits according to the voltages of the air pump terminal (VP) and the air switching valve terminal (VV), and transmits diagnostic information as a signal to the ECM.

For a short time after a cold engine start, the ECM transmits command signals to the air injection control driver to drive the air pump and air switching valve assembly.

The air injection control driver transmits an air pump malfunction signal to the ECM if either of the following conditions is met:

·

The voltage at the air injection control driver terminal relating to the air pump is low despite the air injection control driver receiving command signals from the ECM to drive the air pump.

·

The voltage at the air injection control driver terminal relating to the air pump is high despite the air injection control driver receiving no command signals from the ECM to drive the air pump.


The ECM stored the DTC based on diagnostic signals from the air injection control driver.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Diagnostic information output by the air injection control driver can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the air injection control driver. Reading the waveform while performing the AIR system forced operation provided in the system check allows the possible trouble areas to be narrowed down.


(a) Start the engine and warm it up.

(b) Turn the ignition switch off.

(c) Connect the intelligent tester to the DLC3.

A262769
2.833,0.156 3.24,0.396 0.406,0.24 0.604,0.167 1.188,0.427 0.583,0.26 0.677,1.021 0.917,1.573 false 2.854,0.74 2.917,1.531 false 0.063,0.063 0.271,0.271 0.208,0.208 10 false *a 0.729,0.219 1.302,0.5 0.573,0.281 10 false G146 2.917,0.198 3.313,0.385 0.396,0.188 10 false C98 0.958,1.51 1.677,1.74 0.719,0.229 10 false 30 (AIDI) 2.917,1.542 3.385,1.771 0.469,0.229 10 false 5 (E1)
*a Component with harness connected
(ECM)


(d) Connect oscilloscope probes to the AIDI and E1 terminals of the ECM.

(e) Turn the ignition switch to ON and turn the intelligent tester on.

(f) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.

HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


(g) Start the engine.

(h) Perform the AIR system forced operation while the engine is idling.

G037721
2.938,1.302 3.333,1.5 0.396,0.198 10 false GND 2.677,0.073 3.281,0.271 0.604,0.198 10 false 5 V/DIV. 1.563,1.844 2.354,2.073 0.792,0.229 10 false 20 ms/DIV. 0.563,0.365 2.344,0.563 1.781,0.198 10 true Example: 80% Duty Signal

(i) Monitor the air injection control driver voltage output (duty ratio signal).

Measurement Condition
Item Content
ECM Terminal Name AIDI - E1
Tester Range 5 V/DIV., 20 ms/DIV.
Condition Idling

(j) Turn the ignition switch off.

NOTICE:
·

Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While AIR system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (Wait or Error).

If Error is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the AIR system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




HINT:
·

By using the intelligent tester to perform the Secondary Air Injection Check operation in the system check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR INJECTION CONTROL DRIVER, AIR INJECTION CONTROL DRIVER - BATTERY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the air pump connector.


d.

Disconnect the air injection control driver connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A33 -2 - A34-2 (VP) Always Below 1 Ω
A34-1 (BATT) - Positive battery terminal Always Below 1 Ω
A33-1 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A33-2 or A34-2 (VP) - Body ground Always 10 kΩ or higher



f.

Reconnect the air injection control driver connector.


g.

Reconnect the air pump connector.


h.

Reconnect the cable to the positive (+) battery terminal.


i.

Reconnect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

2.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT AIR PUMP ASSEMBLY

Result:
Proceed to
OK
NG



OK

NG

3.REPLACE AIR PUMP ASSEMBLY
3.REPLACE AIR PUMP ASSEMBLY
a.

Replace the air pump assembly.

Click hereEngine / Hybrid System>2TR-FBE EMISSION CONTROL>AIR PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the intelligent tester on.


e.

Clear DTCs (if stored)

Powertrain > Engine and ECT > Clear DTCs
50002 234

f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

g.

Start the engine after the intelligent tester initialization is finished.


h.

Perform the system check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Check pending DTCs.

OK:

No pending DTC is output.



k.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Proceed to
OK
NG



OK

END

NG