Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P1605  Rough Idling  


DESCRIPTION

If the engine speed becomes lower than a predetermined level, this DTC will be stored.

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

It is necessary to check if the vehicle has run out of fuel before starting diagnosis because this DTC is also stored due to running out of fuel.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1605 Rough Idling After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less
(1 trip detection logic)
·

Intake system connection

·

Purge VSV

·

Brake booster

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Wire harness or connector

·

Air fuel ratio sensor (sensor 1)

·

Power source circuit (purge VSV, fuel injector assembly, ignition coil assembly)

·

Fuel pump (for fuel main tank)

·

Fuel pump control circuit

·

Fuel line

·

Throttle body with motor assembly

·

Camshaft timing oil control valve assembly

·

Knock control sensor

·

Ignition coil assembly

·

Fuel injector assembly

·

Spark plug

·

Air conditioner system

·

Power steering system

·

Electrical load signal circuit

·

A/T system

·

Park/neutral position switch circuit

·

Sub tank fuel pump control circuit

·

Fuel pump (for fuel sub tank)

·

Fuel jet

·

Solenoid valve assembly (for fuel injection volume control)

·

Solenoid valve assembly (for fuel cut control)

·

ECM


Does not come on DTC stored

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuit and systems, DTC P1605 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As this DTC can be stored as a result of certain user actions, even if this DTC is output, if the customer makes no mention of problems, clear this DTC without performing any troubleshooting and return the vehicle to the customer.

·

If any DTCs other than P1605 are output, troubleshoot those DTCs first.

·

Since DTC P1605 is different from other DTCs, the following procedure is shown as a reference.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P1605 is output A
DTC P1605 and other DTCs are output B


HINT:

If any DTCs other than P1605 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the following freeze frame data to see if the engine was cold or warm when the freeze frame data was recorded.

Confirmation Item
Coolant Temp
Initial Engine Coolant Temp
Initial Intake Air Temp
Engine Run Time


e.

Check the following freeze frame data recorded when the engine was idling.

Confirmation Item
Engine Speed
Closed Throttle Position SW
Neutral Position SW Signal


f.

Check the following freeze frame data to see the purge VSV operation status when the freeze frame data was recorded.

Confirmation Item
EVAP (Purge) VSV
Evap Purge Flow
Purge Density Learn Value
EVAP Purge VSV


g.

Check the following freeze frame data to see information related to engine idling from when the freeze frame data was recorded.

Confirmation Item
Shift SW Status (P Range)
Shift SW Status (N Range)
Shift SW Status (D Range)


h.

Check the following freeze frame data to see the engine load and electrical load when the freeze frame data was recorded.

Confirmation Item
Calculate Load
Electrical Load Signal
A/C Signal
Power Steering Signal
Electric Fan Motor


i.

Check the following freeze frame data to see the air fuel ratio recorded when the idle speed was not stable.

Confirmation Item
Short FT #1
Long FT #1
AF Lambda B1S1


j.

Check the following freeze frame data to see the ignition timing recorded when the idle speed was not stable.

Confirmation Item
IGN Advance
Knock Correct Learn Value


k.

Check the following freeze frame data to see the FFV (Flexible Fuel Vehicle) information recorded when the idle speed was not stable.

Confirmation Item
Alcohol Feedback Value
Alc FB Val bfr F/Crrctn by Stall
Trip aft F/Crrctn by Stall
Fuel Dilution Estimate


l.

Use this information to perform a simulation test.


m.

Compare the "Normal Condition" in the Data List (reference values) with the freeze frame data listed above and with the simulation test results to determine the problem cause.

Result:
Result Proceed to
The problem cause can be determined A
The problem cause cannot be determined B




A

REPAIR OR REPLACE MALFUNCTIONING PARTS

B