Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.04
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM U

1GR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


G036662
3.344,0.177 3.823,0.458 0.479,0.281 2.104,0.177 2.583,0.458 0.479,0.281 0.896,0.177 1.375,0.458 0.479,0.281 4.542,0.177 5.021,0.458 0.479,0.281 5.708,0.177 6.188,0.458 0.479,0.281 0.958,0.229 1.406,0.427 0.448,0.198 10 false C129 2.167,0.229 2.615,0.427 0.448,0.198 10 false C130 3.417,0.229 3.865,0.427 0.448,0.198 10 false C131 4.604,0.229 5.052,0.427 0.448,0.198 10 false G154 5.771,0.229 6.219,0.427 0.448,0.198 10 false G155

Measure the voltage according to the value(s) in the table below.


HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G155-3 (BATT) - C131-1 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
G155-7 (+BM) - C131-1 (E1) R-W - BR Power source of throttle motor Always 11 to 14 V
G155-9 (IGSW) - C131-1 (E1) B-O - BR Ignition switch Ignition switch ON 11 to 14 V
G155-1 (+B) - C131-1 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
G155-2 (+B2) - C131-1 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
C131-17 (OC1+) - C131-16 (OC1-) L-B - R-B Camshaft timing oil control valve Idling Pulse generation
(see waveform 1)
C131-15 (OC2+) - C131-14 (OC2-) P-L - Y Camshaft timing oil control valve Idling Pulse generation
(see waveform 1)
G155-8 (MREL) - C131-1 (E1) W-G - BR MAIN relay Ignition switch ON 11 to 14 V
C129-23 (VC) - C129-28 (E2) LG-B - BR Power source for sensors (specific voltage) Ignition switch ON 4.5 to 5.5 V
C129-30 (VG) - C129-29 (E2G) L-W - L-R Mass air flow meter Idling, Shift lever position P or N, A/C switch off 0.5 to 3.0 V
C129-22 (THA) - C129-28 (E2) L-B - BR Intake air temperature sensor Idling, Intake air temperature 20°C (68°F) 0.5 to 3.4 V
C129-21 (THW) - C129-28 (E2) B - BR Engine coolant temperature sensor Idling, Engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C129-20 (VTA1) - C129-28 (E2) B-R - BR Throttle position sensor (for engine control) Ignition switch ON, Throttle valve fully closed 0.5 to 1.2 V
Ignition switch ON, Throttle valve fully open 3.2 to 4.8 V
C129-19 (VTA2) - C129-28 (E2) LG - BR Throttle position sensor (for sensor malfunction detection) Ignition switch ON, Accelerator pedal released 2.1 to 3.1 V
Ignition switch ON, Accelerator pedal depressed 4.6 to 5.0 V
G155-18 (VPA) - G155-20 (EPA) W-L - BR-W Accelerator pedal position sensor (for engine control) Ignition switch ON, Accelerator pedal released 0.5 to 1.1 V
Ignition switch ON, Accelerator pedal depressed 2.6 to 4.5 V
G155-19 (VPA2) - G155-21 (EPA2) GR-G - BR-Y Accelerator pedal position sensor (for sensor malfunctioning detection) Ignition switch ON, Accelerator pedal released 1.2 to 2.0 V
Ignition switch ON, Accelerator pedal depressed 3.4 to 5.0 V
G155-26 (VCPA) - G155-20 (EPA) LG-R - BR-W Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
G155-27 (VCP2) - G155-21 (EPA2) BR-R - BR-Y Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C130-2 (HA1A) - C130-7 (E04) Y - W-B Air fuel ratio sensor heater Idling Pulse generation
(see waveform 2)
Ignition switch ON 11 to 14 V
C130-1 (HA2A) - C130-6 (E05) R-L - W-B Air fuel ratio sensor heater Idling Pulse generation
(see waveform 2)
Ignition switch ON 11 to 14 V
C130-22 (A1A+) - C131-1 (E1) B - BR Air fuel ratio sensor Ignition switch ON 3.3 V*
C130-23 (A2A+) - C131-1 (E1) G - BR Air fuel ratio sensor Ignition switch ON 3.3 V*
C130-30 (A1A-) - C131-1 (E1) W - BR Air fuel ratio sensor Ignition switch ON 2.9 V*
C130-31 (A2A-) - C131-1 (E1) R - BR Air fuel ratio sensor Ignition switch ON 2.9 V*
C129-1 (HT1B) - C131-1 (E1) G - BR Heated oxygen sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C130-5 (HT2B) - C131-1 (E1) L - BR Heated oxygen sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
C129-18 (OX1B) - C129-28 (E2) W - BR Heated oxygen sensor Maintain engine speed at 2500 rpm for 2 minutes after warming up Pulse generation
(see waveform 3)
C130-33 (OX2B) - C129-28 (E2) B - BR Heated oxygen sensor Maintain engine speed at 2500 rpm for 2 minutes after warming up Pulse generation
(see waveform 3)
C131-2 (#10) - C129-7 (E01) L - W-B Fuel injector Ignition switch ON 11 to 14 V
C131-3 (#20) - C129-7 (E01) G - W-B Idling Pulse generation
(see waveform 4)
C131-4 (#30) - C129-7 (E01) R - W-B
C131-5 (#40) - C129-7 (E01) W - W-B
C131-6 (#50) - C129-7 (E01) L - W-B
C131-7 (#60) - C129-7 (E01) Y - W-B
C129-8 (IGT1) - C131-1 (E1) R - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 7)
C129-9 (IGT2) - C131-1 (E1) R-L - BR
C129-10 (IGT3) - C131-1 (E1) G-B - BR
C129-11 (IGT4) - C131-1 (E1) G - BR
C129-12 (IGT5) - C131-1 (E1) B-L - BR
C129-13 (IGT6) - C131-1 (E1) P-L - BR
C129-24 (IGF1) - C131-1 (E1) G-R - BR Ignition coil
(ignition confirmation signal)
Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(see waveform 7)
C130-29 (KNK1) - C130-28 (EKNK) B - W Knock sensor Maintain engine speed at 4000 rpm after warming up Pulse generation
(see waveform 5)
C130-21 (KNK2) - C130-20 (EKN2) R - G Knock sensor Maintain engine speed at 4000 rpm after warming up Pulse generation
(see waveform 5)
C131-19 (VV1+) - C131-29 (VV1-) R - G Variable valve timing (VVT) sensor Idling Pulse generation
(see waveform 6)
C131-18 (VV2+) - C131-28 (VV2-) Y - L Variable valve timing (VVT) sensor Idling Pulse generation
(see waveform 6)
C129-21 (NE+) - C129-20 (NE-) B - W Crankshaft position sensor Idling Pulse generation
(see waveform 6)
C129-34 (PRG) - C131-1 (E1) L - BR Purge VSV Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 8)
G154-8 (SPD) - C131-1 (E1) V-R - BR Speed signal from combination meter Ignition switch ON, Rotate driving wheel slowly Pulse generation
(see waveform 9)
C131-11 (STA) - C131-1 (E1) B-Y - BR Starter signal Cranking 11 to 14 V
C130-8 (NSW) - C131-1 (E1) L-Y - BR Park/Neutral position switch signal Ignition switch ON, Shift position not in P or N 11 to 14 V
Ignition switch ON, Shift position in P or N Below 3.0 V
G155-15 (STP) - C131-1 (E1) G-W - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 3.0 V
G155-16 (ST1-) - C131-1 (E1) R-L - BR Stop light switch Ignition switch ON, Brake pedal depressed Below 3.0 V
Ignition switch ON, Brake pedal released 7.5 to 14 V
C129-5 (M+) - C130-3 (ME01) B - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 10)
C129-4 (M-) - C130-3 (ME01) W - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 11)
G155-10 (FC) - C131-1 (E1) LG-B - BR Fuel pump control Ignition switch ON 11 to 14 V
C131-30 (FPR) - C131-1 (E1) P-L - BR Fuel pump control Ignition switch ON, STA signal OFF Below 3.0 V
Ignition switch ON, STA signal ON 11 to 14 V
G154-30 (W) - C131-1 (E1) R-B - BR MIL Ignition switch ON Below 3.0 V
Idling 11 to 14 V
G155-23 (TC) - C131-1 (E1) P-B - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
G154-1 (TACH) - C131-1 (E1) B-W - BR Engine speed Idling Pulse generation
(see waveform 12)
C129-33 (ACIS) - C131-1 (E1) G-B - BR VSV for ACIS Ignition switch ON 11 to 14 V
C131-10 (PSW) - C131-1 (E1) G-Y - BR Power steering pressure switch Ignition switch ON 11 to 14 V

HINT:

*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.


a.
A301905
1.813,1.875 2.771,2.104 0.958,0.229 10 false 1 msec./DIV. 0.583,1.125 0.99,1.333 0.406,0.208 10 false GND 0.594,0.219 1.552,0.448 0.958,0.229 10 false 5 V/DIV.

WAVEFORM 1

Camshaft Timing Oil Control Valve


ECM Terminal Name Between OC1+ and OC1- or OC2+ and OC2-
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling


b.
A114645
0.052,0.071 0.621,0.247 0.569,0.176 10 5 V/DIV. 1.162,1.942 2.082,2.118 0.92,0.176 10 10 msec./DIV.

WAVEFORM 2

Air Fuel Ratio Sensor Heater


ECM Terminal Name Between HA1A and E04 or HA2A and E05
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling


c.
A301906
0.344,0.219 1.229,0.417 0.885,0.198 10 false 0.2 V/DIV. 0.573,1.469 1.052,1.667 0.479,0.198 10 false GND 1.813,1.885 2.99,2.135 1.177,0.25 10 false 200 msec./DIV.

WAVEFORM 3

Heated Oxygen Sensor


ECM Terminal Name Between OX1B and E2 or OX2B and E2
Tester Range 0.2 V/DIV., 200 msec./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

In the Data List, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.



d.
G035622
0.417,0.313 1.052,0.531 0.635,0.219 10 false 30 V/DIV. 1.646,1.917 2.615,2.083 0.969,0.167 10 false 20 msec./DIV. 0.49,1.208 0.844,1.385 0.354,0.177 10 false GND

WAVEFORM 4

Fuel Injector


ECM Terminal Name Between #10 (to #60) and E01
Tester Range 30 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



e.
A301915
2.396,0.521 2.99,0.76 0.594,0.24 10 false 1 V/DIV. 2.635,0.99 3.021,1.198 0.385,0.208 10 false GND 1.01,1.896 1.948,2.083 0.938,0.188 10 false 1 msec./DIV.

WAVEFORM 5

Knock Sensor


ECM Terminal Name Between KNK1 and EKNK or KNK2 and EKN2
Tester Range 1 V/DIV., 1 msec./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveform and amplitude displayed differ slightly depending on the vehicle.




f.
G035795
3.01,1.219 3.365,1.417 0.354,0.198 10 false GND 3.01,1.615 3.365,1.813 0.354,0.198 10 false GND 3.01,0.615 3.365,0.813 0.354,0.198 10 false GND 0.167,1.146 0.49,1.344 0.323,0.198 10 false VV1 0.167,1.573 0.49,1.771 0.323,0.198 10 false VV2 0.208,0.625 0.479,0.823 0.271,0.198 10 false NE 2.792,0.052 3.333,0.24 0.542,0.188 10 false 5 V/DIV. 1.219,1.896 2.177,2.094 0.958,0.198 10 false 20 msec./DIV.

WAVEFORM 6

Crankshaft Position Sensor and VVT Sensor


ECM Terminal Name Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



g.
G035664
0.177,0.531 0.469,0.729 0.292,0.198 10 false IGT 0.177,1.438 0.469,1.635 0.292,0.198 10 false IGF 2.76,0.385 3.333,0.583 0.573,0.198 10 false 2 V/DIV. 2.875,1.031 3.229,1.229 0.354,0.198 10 false GND 2.885,1.875 3.24,2.073 0.354,0.198 10 false GND 1.448,1.99 2.365,2.167 0.917,0.177 10 false 20 msec./DIV.

WAVEFORM 7

Ignition Coil Signal (IGT and IGF Signal)


ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Ranges 2 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



h.
A205411
2.583,0.323 3.208,0.479 0.625,0.156 10 false 10 V/DIV. 1.042,1.927 1.948,2.104 0.906,0.177 10 false 20 msec./DIV. 2.677,1.094 3.042,1.271 0.365,0.177 10 false GND

WAVEFORM 8

Purge VSV


ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 msec./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



i.
A301907
0.469,0.281 1.375,0.5 0.906,0.219 10 false 2 V/DIV. 0.542,1.167 0.938,1.396 0.396,0.229 10 false GND 1.792,1.896 2.781,2.115 0.99,0.219 10 false 20 msec./DIV.

WAVEFORM 9

Vehicle Speed Signal


ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Driving at 20 mph (12 km/h)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



j.
A208000
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.237,1.806 2.058,1.965 0.821,0.159 10 1 msec./DIV.

WAVEFORM 10

Throttle Actuator Positive Terminal


ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



k.
A245848
2.854,1.021 3.188,1.167 0.333,0.146 10 false GND 2.635,0.281 3.177,0.427 0.542,0.146 10 false 5 V/DIV. 0.479,0.625 0.667,0.771 0.188,0.146 10 false M- 1.25,1.823 2.083,1.969 0.833,0.146 10 false 1 msec./DIV.

WAVEFORM 11

Throttle Actuator Negative Terminal


ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
A301908
0.438,0.281 1.094,0.51 0.656,0.229 10 false 5 V/DIV. 0.49,1.188 1.146,1.417 0.656,0.229 10 false GND 1.729,1.896 2.719,2.135 0.99,0.24 10 false 10 msec./DIV.

WAVEFORM 12

Engine Speed Signal


ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.