Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › RELAY › from 2012.04
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052142 RELAY G

1GR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT NO. 1 INTEGRATION RELAY (C/OPN)

a.
A225101
2.354,1.563 2.719,1.781 0.365,0.219 1.208,1.563 1.573,1.781 0.365,0.219 0.323,1.563 0.688,1.781 0.365,0.219 2.469,1.583 2.646,1.771 0.177,0.188 10 false 1I 1.313,1.583 1.479,1.76 0.167,0.177 10 false 1J 0.406,1.583 0.625,1.76 0.219,0.177 10 false 1H 0.115,0.083 0.313,0.281 0.198,0.198 10 false *a
*a Component without harness connected
(Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-5 - 1J-8 Battery voltage not applied to terminals 1J-6 and 1J-7 10 kΩ or higher
Battery voltage applied to terminals 1J-6 and 1J-7 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.


Hide 2.INSPECT NO. 1 INTEGRATION RELAY (MAIN)

a.

Check the EFI fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω


If the result is not as specified, replace the EFI fuse.



b.

Check the MAIN relay.

i.
A225101
2.354,1.563 2.719,1.781 0.365,0.219 1.208,1.563 1.573,1.781 0.365,0.219 0.323,1.563 0.688,1.781 0.365,0.219 2.469,1.583 2.646,1.771 0.177,0.188 10 false 1I 1.313,1.583 1.479,1.76 0.167,0.177 10 false 1J 0.406,1.583 0.625,1.76 0.219,0.177 10 false 1H 0.115,0.083 0.313,0.281 0.198,0.198 10 false *a
*a Component without harness connected
(Integration Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-1 - 1J-4 Battery voltage not applied to terminals 1J-2 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1J-2 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 3.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F)

a.
A184106
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 3 1.208,0.729 1.406,0.906 0.198,0.177 10 5 0.208,1.271 0.365,1.448 0.156,0.177 10 2 1.208,1.271 1.438,1.448 0.229,0.177 10 1 3.021,1.521 3.229,1.698 0.208,0.177 10 3 3.0,1.021 3.198,1.198 0.198,0.177 10 5 3.094,0.083 3.25,0.26 0.156,0.177 10 2 1.417,0.083 1.646,0.26 0.229,0.177 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the air fuel ratio sensor heater relay.


Hide 4.INSPECT FUEL PUMP RELAY (F/PMP)

a.
A087121
2.531,1.135 3,1.135 false 2.531,1.635 3,1.635 false 2.667,0.719 3.01,0.719 false 1.677,0.719 1.99,0.719 false 2.604,0.198 2.51,0.198 2.51,0.198 2.333,0.563 false 0.313,1.438 0.469,1.615 0.156,0.177 10 false 1 1.552,0.635 1.719,0.792 0.167,0.156 10 false 1 1.313,1.427 1.448,1.604 0.135,0.177 10 false 2 3.063,0.625 3.188,0.802 0.125,0.177 10 false 2 0.313,0.896 0.469,1.073 0.156,0.177 10 false 3 3.063,1.542 3.219,1.719 0.156,0.177 10 false 3 0.938,0.365 1.115,0.531 0.177,0.167 10 false 4 2.656,0.104 2.781,0.271 0.125,0.167 10 false 4 1.313,0.885 1.479,1.094 0.167,0.208 10 false 5 3.063,1.052 3.188,1.25 0.125,0.198 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the fuel pump relay.