Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › ENGINE UNIT(w/o Glow Plug Controller)
RM1840EF _51 Engine / Hybrid System _009573 1KD-FTV ENGINE MECHANICAL _0052152 ENGINE UNIT(w/o Glow Plug Controller) G

1KD-FTV ENGINE MECHANICAL  ENGINE UNIT(w/o Glow Plug Controller)  INSPECTION  


PROCEDURE

Hide 1.INSPECT INJECTION GEAR BEARING

a.

Check that the bearing is not rough or worn.

If necessary, replace the injection gear.


Hide 2.INSPECT NO. 1 IDLE GEAR OIL CLEARANCE

a.
A060287

Using a cylinder gauge, measure the inside diameter of the idle gear.

Standard idle gear inside diameter:

44.000 to 44.025 mm (1.732 to 1.734 in.)



b.
A051343

Using a micrometer, measure the diameter of the idle gear shaft.

Standard idle gear shaft diameter:

43.955 to 43.990 mm (1.730 to 1.732 in.)



c.

Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.

Standard oil clearance:

0.01 to 0.07 mm (0.000394 to 0.00276 in.)


Maximum oil clearance:

0.20 mm (0.00787 in.)


If the oil clearance is more than the maximum, replace the gear and shaft.


Hide 3.INSPECT INTAKE MANIFOLD

a.
A098945

Using a precision straightedge and feeler gauge, measure the warpage of the surface of the intake manifold that contacts the cylinder head.

Maximum warpage:

0.4 mm (0.0157 in.)


If the warpage is more than the maximum, replace the intake manifold.


Hide 4.INSPECT EXHAUST MANIFOLD

a.
A098949

Using a precision straightedge and feeler gauge, measure the warpage of the surface of the exhaust manifold that contacts the cylinder head.

Maximum warpage:

0.4 mm (0.0157 in.)


If the warpage is more than the maximum, replace the exhaust manifold.


Hide 5.INSPECT CAMSHAFT

a.

Inspect the circle runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.

Inspect the cam lobe height.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

47.18 to 47.28 mm (1.857 to 1.861 in.)


Minimum cam lobe height:

46.76 mm (1.841 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.

Inspect the diameter of the camshaft journal.

i.

Using a micrometer, measure the diameter of the camshaft journal for the camshaft bearing.

Standard diameter:

27.969 to 27.985 mm (1.101 to 1.102 in.)


If the diameter is not as specified, check the oil clearance.



d.
A061825

Using a dial indicator, measure the backlash.

i.

Install the 2 camshafts.


ii.

Using a dial indicator, measure the backlash.

Standard backlash:

0.035 to 0.089 mm (0.00138 to 0.00350 in.)


Maximum backlash:

0.189 mm (0.00744 in.)


If the backlash is more than the maximum, replace the 2 camshafts.


iii.

Remove the 2 camshafts.



Hide 6.INSPECT NO. 2 CAMSHAFT

a.

Inspect the circle runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.

Inspect the cam lobe height.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

48.07 to 48.17 mm (1.893 to 1.896 in.)


Minimum cam lobe height:

47.92 mm (1.887 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.

Inspect the diameter of the camshaft journal.

i.

Using a micrometer, measure the diameter of the camshaft journal for the camshaft bearing.

Standard diameter:

27.969 to 27.985 mm (1.101 to 1.102 in.)


If the diameter is not as specified, check the oil clearance.



Hide 7.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the bearing caps and journals.


b.

Check the bearings for flaking and scoring.

If the bearings are damaged, replace the bearing caps and cylinder head as a set.


c.

Place the camshaft on the cylinder head.


d.
A226776
1.521,1.104 1.146,0.563 1.146,0.563 1.073,0.563 true 1.448,3.615 1.063,3.073 1.063,3.073 1,3.073 true 0.188,0.167 0.417,0.344 0.229,0.177 10 false *a 0.188,2.51 0.417,2.688 0.229,0.177 10 false *b 0.833,0.458 1,0.635 0.167,0.177 10 true *1 0.792,2.969 0.958,3.146 0.167,0.177 10 false *1
*1 Plastigage
*a Intake Side
*b Exhaust Side


Lay a strip of Plastigage across each of the journals.


e.

Install the bearing caps.

NOTICE:

Do not turn the camshaft.



f.

Remove the bearing caps.


g.
A226777
1.573,1.021 1.188,0.479 1.188,0.479 1.115,0.479 true 1.479,3.552 1.104,3.01 1.104,3.01 1.031,3.01 true 0.188,0.115 0.417,0.292 0.229,0.177 10 false *a 0.188,2.458 0.417,2.635 0.229,0.177 10 false *b 0.896,0.385 1.063,0.563 0.167,0.177 10 true *1 0.833,2.917 1,3.094 0.167,0.177 10 false *1
*1 Plastigage
*a Intake Side
*b Exhaust Side


Measure the Plastigage at its widest point.

Standard oil clearance:

0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum oil clearance:

0.1 mm (0.00394 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.


h.

Completely remove the Plastigage.


i.

Remove the camshaft.


Hide 8.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Install the camshaft.


b.
A226778
0.125,0.052 0.354,0.229 0.229,0.177 10 false *a 0.125,2.396 0.354,2.573 0.229,0.177 10 false *b
*a Intake Side
*b Exhaust Side


Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.185 mm (0.00138 to 0.0728 in.)


Maximum thrust clearance:

0.25 mm (0.00984 in.)


If the thrust clearance is more than the maximum, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.


c.

Remove the camshaft.


Hide 9.INSPECT CYLINDER HEAD SET BOLT

a.
A226805

Using a vernier caliper, measure the diameter of the most elongated threads in the measurement area.

Standard outside diameter:

11.76 to 11.97 mm (0.463 to 0.471 in.)


Minimum outside diameter:

11.6 mm (0.457 in.)


HINT:

If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the smallest diameter.


If the diameter is less than the minimum, replace the cylinder head set bolt.