Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CYLINDER BLOCK(w/o Glow Plug Controller) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009573 1KD-FTV ENGINE MECHANICAL _0052154 CYLINDER BLOCK(w/o Glow Plug Controller) A

1KD-FTV ENGINE MECHANICAL  CYLINDER BLOCK(w/o Glow Plug Controller)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Install the stud bolts.

A303250
0.625,0.208 0.938,0.406 0.313,0.198 10 false *a 3.927,0.198 4.24,0.396 0.313,0.198 10 false *b 0.646,2.271 0.958,2.469 0.313,0.198 10 false *c 3.927,2.271 4.24,2.469 0.313,0.198 10 false *d 1.948,1.594 2.115,1.833 0.167,0.24 10 false A 4.458,0.188 4.646,0.396 0.188,0.208 10 false B 2.427,2.51 2.625,2.708 0.198,0.198 10 false C 5.458,2.375 5.677,2.573 0.219,0.198 10 false D 1.49,1.479 1.656,1.719 0.167,0.24 10 false A 0.969,1.615 1.135,1.854 0.167,0.24 10 false A 5.552,0.063 5.74,0.271 0.188,0.208 10 false B 2,3.042 2.198,3.24 0.198,0.198 10 false C 0.99,4.302 1.188,4.5 0.198,0.198 10 false C 5.656,2.375 5.875,2.573 0.219,0.198 10 false D 1.198,4.75 1.708,4.948 0.51,0.198 10 false 9 mm 2.385,7.813 2.969,8.01 0.583,0.198 10 false 26 mm 2.396,5.698 3.052,5.885 0.656,0.188 10 false 69 mm 1.146,7.542 1.667,7.729 0.521,0.188 10 false 12 mm 4.813,5.875 5.51,6.094 0.698,0.219 10 false 9.5 mm 6.052,6.198 6.635,6.385 0.583,0.188 10 false 29 mm 6.031,7.792 6.615,7.979 0.583,0.188 10 false 23 mm 4.823,7.594 5.583,7.813 0.76,0.219 10 false 9 mm 1.375,9.49 1.573,9.688 0.198,0.198 10 false C 1.375,6.948 1.573,7.146 0.198,0.198 10 false A 5.229,6.938 5.427,7.135 0.198,0.198 10 false B 5.219,9.427 5.417,9.625 0.198,0.198 10 false D 1.344,7.094 1.698,7.292 0.354,0.198 10 false M6 5.188,7.094 5.531,7.302 0.344,0.208 10 false M6 1.333,9.635 1.698,9.844 0.365,0.208 10 false M6 5.188,9.583 5.625,9.75 0.438,0.167 10 false M6 2.635,0.75 2.823,0.958 0.188,0.208 10 false B 1.177,4.896 1.854,5.125 0.677,0.229 10 false (0.354 in.) 2.396,5.854 3.042,6.073 0.646,0.219 10 false (2.72 in.) 1.156,6.74 1.833,6.969 0.677,0.229 10 false (0.354 in.) 1.198,6.604 1.708,6.802 0.51,0.198 10 false 9 mm 1.146,7.698 1.927,7.906 0.781,0.208 10 false (0.472 in.) 1.156,9.125 1.938,9.333 0.781,0.208 10 false (0.472 in.) 1.146,8.979 1.667,9.167 0.521,0.188 10 false 12 mm 2.385,8.885 3.063,9.094 0.677,0.208 10 false (1.02 in.) 4.823,6.021 5.552,6.24 0.729,0.219 10 false (0.374 in.) 4.802,6.719 5.531,6.938 0.729,0.219 10 false (0.374 in.) 4.802,6.583 5.5,6.802 0.698,0.219 10 false 9.5 mm 6.052,6.365 6.708,6.552 0.656,0.188 10 false (1.14 in.) 4.813,7.74 5.573,7.958 0.76,0.219 10 false (0.354 in.) 4.823,9.177 5.583,9.396 0.76,0.219 10 false (0.354 in.) 4.844,9.021 5.604,9.24 0.76,0.219 10 false 9 mm 6.031,8.906 6.719,9.125 0.688,0.219 10 false (0.906 in.) 1.146,8.031 1.667,8.219 0.521,0.188 10 false 12 mm 1.135,8.188 1.917,8.396 0.781,0.208 10 false (0.472 in.) 4.813,8.083 5.573,8.302 0.76,0.219 10 false 9 mm 4.792,8.24 5.552,8.458 0.76,0.219 10 false (0.354 in.) 5.24,8.458 5.438,8.656 0.198,0.198 10 false D 5.188,8.615 5.531,8.823 0.344,0.208 10 false M6 1.385,8.458 1.583,8.656 0.198,0.198 10 false C 1.344,8.615 1.688,8.823 0.344,0.208 10 false M6 2.385,7.979 3.031,8.198 0.646,0.219 10 false (1.02 in.) 6.01,7.948 6.656,8.167 0.646,0.219 10 false (0.906 in.)
*a Front Side *b Left Side
*c Oil Pan Side *d Right Side



Hide 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A060268

Align the pin of the No. 1 oil nozzle with the pin hole of the cylinder block.


b.

Install the 4 No. 1 oil nozzles with the 4 check valves.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 3.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A060203

Using a small screwdriver, install a new snap ring on one side of the piston pin hole.


b.

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin with engine oil.


d.
A226793
0.917,0.625 1.073,0.875 1.073,0.875 1.073,0.906 false 0.875,2.385 0.448,2.385 true 0.99,0.938 1.167,1.104 0.177,0.167 10 false *1 0.26,2.292 0.438,2.458 0.177,0.167 10 false *2
*1 Front Mark (Arrow)
*2 Front Mark (Protrusion)


Align the front marks of the piston and connecting rod, connect the connecting rod to the piston, and then push in the piston pin with your thumb.


e.

Check the fit between the piston and piston pin. Try to move the piston back and forth on the piston pin.


f.
A149754

Using a small screwdriver, install a new snap ring on the other side of the piston pin hole.


Hide 4.INSTALL PISTON RING SET

a.
A226794
1.688,0.146 1.688,0.469 false 1.594,1.917 1.76,2.073 0.167,0.156 10 false *2 1.594,0.49 1.76,0.646 0.167,0.156 10 false *1
*1 Coil Joint
*2 Oil Ring End Gap


Install the coil and oil ring by hand.

HINT:

Make sure the end gap of the oil ring and the coil joint are on opposite sides.



b.
A226155
0.698,0.698 0.375,0.302 0.375,0.302 0.292,0.302 false 0.698,1.396 0.375,1.052 0.375,1.052 0.292,1.052 false 0.063,0.219 0.26,0.385 0.198,0.167 10 false *1 0.073,0.979 0.271,1.146 0.198,0.167 10 false *2
*1 No. 1 Piston Ring
*2 No. 2 Piston Ring


Using a piston ring expander, install the No. 1 and No. 2 piston rings with the code marks facing upward.

Code Mark:
Item Specified Condition
No. 1 Piston Ring w/ EGR Cooler NAA
w/o EGR Cooler NKD
No. 2 Piston Ring N



c.
A226156
1.688,0.656 1.885,0.208 1.885,0.208 1.948,0.208 true 0.76,0.417 0.948,0.604 0.188,0.188 10 false *1 2.438,0.406 2.625,0.594 0.188,0.188 10 false *2 2.438,1.615 2.625,1.802 0.188,0.188 10 false *4 0.76,1.615 0.948,1.802 0.188,0.188 10 false *3 1.99,0.125 2.177,0.313 0.188,0.188 10 false *5
*1 No. 1 Piston Ring
*2 Oil Ring
*3 Coil
*4 No. 2 Piston Ring
*5 Front Mark (Arrow)


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



Hide 5.INSTALL CRANKSHAFT BEARING

A060228

HINT:

Upper bearings have an oil groove and oil hole. Lower bearings do not.


a.

Align the bearing claw with the claw groove of the cylinder block and push in the 5 upper bearings.


b.
A060190

Align the bearing claw with the claw groove of the crankshaft bearing cap and push in the 5 lower bearings.


Hide 6.INSTALL CRANKSHAFT

a.

Place the crankshaft on the cylinder block.


b.
A060188

Push the crankshaft in one direction and install one thrust washer to the No. 5 journal position with the oil groove facing outward.


c.

Push the crankshaft in the opposite direction and install the other thrust washer to the No. 5 journal position with the oil groove facing outward.


d.
A060189

Install the 2 thrust washers to the No. 5 bearing cap with the grooves facing outward.


e.
A060226

Install the 5 crankshaft bearing caps to their proper locations.


f.
A060270
0.813,0.427 0.958,0.625 0.146,0.198 10 false 4 3.135,1.135 3.281,1.333 0.146,0.198 10 true 8 1.875,0.021 2.021,0.219 0.146,0.198 10 false 6 2.073,1.583 2.219,1.781 0.146,0.198 10 true 2 1.406,0.177 1.552,0.375 0.146,0.198 10 true 1 1.49,1.823 1.635,2.021 0.146,0.198 10 true 5 0.875,1.979 1.021,2.177 0.146,0.198 10 true 9 3.01,0.063 3.156,0.26 0.146,0.198 10 true 7 2.615,1.333 2.76,1.531 0.146,0.198 10 true 3 0.125,0.667 0.375,0.865 0.25,0.198 10 false 10

Install the crankshaft bearing cap bolts.

HINT:
·

The crankshaft bearing cap bolts are tightened in 2 progressive steps.

·

If a crankshaft bearing cap bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the bolt heads of the crankshaft bearing cap bolts.


ii.

Install and uniformly tighten the 10 bolts of the crankshaft bearing caps in several passes in the sequence shown in the illustration.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

If any one of the bearing cap bolts does not meet the torque specification, replace the bearing cap bolt.


iii.
A303251
0.844,0.917 0.844,0.802 0.844,0.802 0.646,0.344 true 0.125,0.208 0.354,0.438 0.229,0.229 10 false 90° 1.198,0.167 1.427,0.396 0.229,0.229 10 false 90° 0.354,0.615 0.583,0.844 0.229,0.229 10 false *a 0.75,0.948 0.979,1.177 0.229,0.229 10 false *1
*1 Paint Mark
*a Front


Mark the front of each crankshaft bearing cap bolt with paint.


iv.

Tighten the crankshaft bearing cap bolts by 90° in the numerical order shown in the previous illustration.


v.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


h.

Check the crankshaft thrust clearance.


Hide 7.INSTALL CONNECTING ROD BEARING

a.

Align the bearing claw with the groove of the connecting rod or connecting rod cap.


b.

Install the bearings to the connecting rod and connecting rod cap.


Hide 9.INSTALL PISTON AND CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.

Check the positions of the piston ring ends.


c.
A226796
0.293,0.959 0.48,1.133 0.187,0.173 10 *1
*1 Front Mark (Arrow)


Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.


d.

Place the connecting rod cap on the connecting rod.

i.
A303252
0.583,0.708 0.406,1.333 0.406,1.333 0.469,0.698 true 0.292,1.354 0.604,1.552 0.313,0.198 10 false *1
*1 Matchmark


Match each numbered connecting rod cap with the correct connecting rod.


ii.
A060237

Align the pins of the connecting rod cap with the pin holes of the connecting rod and install the connecting rod cap.


iii.
A060238
1.396,0.844 0.667,1.292 0.667,1.292 0.667,1.396 true 0.563,1.417 0.75,1.583 0.188,0.167 10 false *1
*1 Front Mark (Protrusion)
V100135

Front


Check that the front mark of the connecting rod cap is facing forward.



e.

Install the connecting rod cap bolts.

HINT:
·

The connecting rod cap bolts are tightened in 2 progressive steps.

·

If any connecting rod cap bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


ii.

Install and alternately tighten the bolts of the connecting rod cap in several passes.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:

If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolt.



iii.
A060197
0.5,0.365 0.625,0.99 0.625,0.99 0.625,1.052 true 0.406,0.01 0.74,0.198 0.333,0.188 10 false 90° 0.969,0.146 1.302,0.333 0.333,0.188 10 false 90° 0.198,0.594 0.375,0.792 0.177,0.198 10 false *a 0.531,1.063 0.719,1.208 0.188,0.146 10 false *1
*1 Paint Mark
*a Front


Mark the front of each connecting rod cap bolt with paint.


iv.

Tighten the connecting rod cap bolts by 90° as shown in the illustration.


v.

Check that the paint marks are now at a 90° angle to the front.



f.

Check that the crankshaft turns smoothly.


Hide 11.INSTALL CYLINDER BLOCK OIL ORIFICE