1.CLEAN CYLINDER HEAD SUB-ASSEMBLY
Using a gasket scraper, remove all the gasket material from the surface of the cylinder head that contacts the cylinder block.
Be careful not to scratch the surface of the cylinder head.
Using a soft brush and solvent, thoroughly clean the cylinder head.
Using a valve guide bushing brush and solvent, clean all the guide bushes.
2.INSPECT CYLINDER HEAD SUB-ASSEMBLY
| *a | Cylinder Block Side |
| *b | Intake Manifold Side |
| *c | Exhaust Manifold Side |
Inspect the cylinder head for warpage.
Using a precision straightedge and feeler gauge, measure the surfaces of the cylinder head that contact the cylinder block and manifolds for warpage.
0.15 mm (0.00591 in.)
If the warpage is more than the maximum, replace the cylinder head sub-assembly.
Inspect the cylinder head for cracks.
Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
If there are cracks, replace the cylinder head sub-assembly.
3.CLEAN INTAKE VALVE
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
4.INSPECT INTAKE VALVE
Using a micrometer, measure the diameter of the valve stem.
5.970 to 5.985 mm (0.235 to 0.236 in.)
If the diameter is not as specified, replace the intake valve.
| *1 | Valve Face Angle |
Check the valve face angle.
Grind the valve enough to remove any pits and carbon.
Check that the valve is ground to the correct valve face angle.
44.5°
If the result is not as specified, replace the valve.
| *1 | Margin Thickness |
Check the valve head margin thickness.
1.1 mm (0.0433 in.)
0.8 mm (0.0315 in.)
If the margin thickness is less than the minimum, replace the intake valve.
Check the overall valve length.
105.15 to 105.75 mm (4.14 to 4.16 in.)
104.65 mm (4.12 in.)
If the overall length is less than the minimum, replace the intake valve.
Check the surface of the valve stem tip for wear.
If the valve stem tip is worn, resurface the tip with a grinder or replace the intake valve.
Do not grind the valve so it becomes shorter than the minimum overall length.
5.CLEAN EXHAUST VALVE
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the exhaust valve.
6.INSPECT EXHAUST VALVE
Using a micrometer, measure the diameter of the valve stem.
5.960 to 5.975 mm (0.2346 to 0.2352 in.)
If the diameter is not as specified, replace the valve.
| *1 | Valve Face Angle |
Check the valve face angle.
Grind the valve enough to remove any pits and carbon.
Check that the valve is ground to the correct valve face angle.
44.5°
If the result is not as specified, replace the exhaust valve.
| *1 | Margin Thickness |
Check the valve head margin thickness.
1.2 mm (0.0472 in.)
0.7 mm (0.0276 in.)
If the margin thickness is less than the minimum, replace the valve.
Check the overall valve length.
105.02 to 105.62 mm (4.13 to 4.16 in.)
104.52 mm (4.11 in.)
If the overall length is less than the minimum, replace the exhaust valve.
Check the surface of the valve stem tip for wear.
If the valve stem tip is worn, resurface the tip with a grinder or replace the exhaust valve.
Do not grind the valve so it becomes shorter than the minimum overall length.
7.INSPECT INNER COMPRESSION SPRING
| *1 | Deviation |
Using a steel square, measure the deviation of the spring.
2.0 mm (0.0787 in.)
If the deviation is more than the maximum, replace the inner compression spring.
Using a vernier caliper, measure the free length of the spring.
48.4 mm (1.91 in.)
If the free length is not as specified, replace the inner compression spring.
Using a spring tester, measure the tension of the valve spring at the specified installed length.
175 to 193 N (18 to 19 kgf, 39.4 to 43.3 lbf)
If the tension is not as specified, replace the inner compression spring.
8.INSPECT INTAKE VALVE GUIDE BUSH
Using a caliper gauge, measure the inside diameter of the valve guide bush.
6.01 to 6.03 mm (0.2366 to 0.2374 in.)
Subtract the valve stem diameter measurement (refer to the intake valve inspection procedures above) from the valve guide bush inside diameter measurement.
0.025 to 0.060 mm (0.000986 to 0.00236 in.)
0.08 mm (0.00315 in.)
If the oil clearance is more than the maximum, replace the intake valve and intake valve guide bush.
9.INSPECT EXHAUST VALVE GUIDE BUSH
Using a caliper gauge, measure the inside diameter of the valve guide bush.
6.01 to 6.03 mm (0.2366 to 0.2374 in.)
Subtract the valve stem diameter measurement (refer to the exhaust valve inspection procedures above) from the valve guide bush inside diameter measurement.
0.035 to 0.070 mm (0.00138 to 0.00276 in.)
0.10 mm (0.00394 in.)
If the oil clearance is more than the maximum, replace the valve and guide bush.
10.INSPECT INTAKE VALVE SEAT
| *1 | 45° Carbide Cutter |
Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.
| *1 | Width |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve against the valve seat.
Check the valve face and valve seat.
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.2 and 1.6 mm (0.0472 and 0.0630 in.).
If the contact surfaces are not as specified, resurface the valve intake seat. If necessary, replace the intake valve.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If the contact surfaces are not as specified, resurface the intake valve seat. If necessary, replace the intake valve.
11.INSPECT EXHAUST VALVE SEAT
| *1 | 45° Carbide Cutter |
Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the valve seats.
| *1 | Width |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve against the valve seat.
Check the valve face and valve seat.
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.6 and 2.0 mm (0.0630 and 0.0787 in.)
If the contact surfaces are not as specified, resurface the exhaust valve seat. If necessary, replace the exhaust valve.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If the contact surfaces are not as specified, resurface the exhaust valve seat. If necessary, replace the exhaust valve.
12.INSPECT VALVE LIFTER
Using a micrometer, measure the lifter diameter.
30.966 to 30.976 mm (1.219 to 1.220 in.)
Using a caliper gauge, measure the lifter bore diameter of the cylinder head.
31.000 to 31.021 mm (1.220 to 1.221 in.)
Measure the oil clearance by subtracting the lifter diameter measurement from the lifter bore diameter measurement.
0.024 to 0.055 mm (0.000945 to 0.00217 in.)
0.095 mm (0.00374 in.)
If the oil clearance is more than the maximum, replace the lifter. If necessary, replace the cylinder head.
13.INSPECT CAMSHAFT OIL CLEARANCE
14.INSPECT CAMSHAFT THRUST CLEARANCE