Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER HEAD(w/o DPF)
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052173 CYLINDER HEAD(w/o DPF) A

2KD-FTV ENGINE MECHANICAL  CYLINDER HEAD(w/o DPF)  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.
A059922
1.563,1.5 1.063,0.604 1.063,0.604 1.542,0.802 true 0.729,0.521 1.042,0.688 0.313,0.167 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.


d.

Select a new guide bush.

New Guide Bush:
Item Specified Condition
Bush bore diameter 10.985 to 11.006 mm (0.432 to 0.433 in.) 11.035 to 11.056 mm (0.434 to 0.435 in.)
Bush to be used STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 11.006 mm (0.433 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.434 and 0.435 in.).

If the bush bore diameter of the cylinder head is more than 11.056 mm (0.435 in.), replace the cylinder head.


e.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


f.
A303227
0.865,1.479 1.792,1.385 1.792,1.385 0.906,1.031 true 1.844,1.323 2.302,1.521 0.458,0.198 10 false SST 3.188,0.417 3.375,0.656 0.188,0.24 10 false H

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)

Standard protrusion height (H):

10.3 to 10.7 mm (0.406 to 0.421 in.)



g.
A059166
1.635,0.635 1.313,0.313 1.313,0.313 1.229,0.313 false 1.031,0.219 1.208,0.396 0.177,0.177 10 false *1
*1 Sharp 6.0 mm Reamer


Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard clearance:

0.025 to 0.060 mm (0.00984 to 0.00236 in.)



Hide 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.
A059923
1.594,0.906 0.979,0.729 0.979,0.729 1.635,1.583 true 0.688,0.625 1.031,0.802 0.344,0.177 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.


d.

Select a new guide bush.

New Guide Bush:
Item Specified Condition
Bush bore diameter 10.985 to 11.006 mm (0.4325 to 0.4333 in.) 11.035 to 11.056 mm (0.4344 to 0.4353 in.)
Bush to be used STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.4344 and 0.4353 in.).

If the bush bore diameter of the cylinder head is more than 11.056 mm (0.4353 in.), replace the cylinder head.


e.

Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


f.
A303228
0.969,1.573 1.656,1.552 1.656,1.552 1,0.958 true 1.74,1.49 2.198,1.688 0.458,0.198 10 false SST 3.135,0.813 3.323,1.042 0.188,0.229 10 false H

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)

Standard protrusion height (H):

10.3 to 10.7 mm (0.406 to 0.421 in.)



g.
A059170
1.635,0.656 1.292,0.313 1.292,0.313 1.198,0.313 false 1,0.208 1.177,0.385 0.177,0.177 10 false *1
*1 Sharp 6.0 mm Reamer


Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard clearance:

0.035 to 0.070 mm (0.00138 to 0.00276 in.)



Hide 3.REPLACE RING PIN

HINT:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pin.


b.

Using a plastic-faced hammer, tap in a new ring pin until the pin stops.

Standard protrusion:

Less than 5 mm (0.197 in.)


A200441
3.906,0.938 3.458,0.531 3.458,0.531 3.667,0.531 false 3.708,0.448 4.896,0.615 1.188,0.167 10 false 8 mm (0.315 in.) 3.615,1.365 4.802,1.542 1.188,0.177 10 false 10 mm (0.394 in.) 5.792,1.281 6.01,1.469 0.219,0.188 10 false *a
*a Less than 5 mm (0.197 in.) - -