1.INSPECT CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
0.15 to 0.35 mm (0.00591 to 0.0138 in.)
0.40 mm (0.0157 in.)
If the thrust clearance is more than the maximum, replace the connecting rod assembly. If necessary, replace the crankshaft.
2.INSPECT CONNECTING ROD OIL CLEARANCE
Check that the matchmarks on the connecting rod and cap are aligned to ensure correct reassembly.
The matchmarks on the connecting rods and caps are for ensuring correct reassembly.
Remove the 2 connecting rod cap bolts.
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
Keep the lower bearing installed to the connecting rod cap.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches.
| *1 | Plastigage |
Lay a strip of Plastigage on the crank pin.
| *1 | Front Mark |
Check that the front mark of the connecting rod cap is facing forward.
Install the connecting rod cap (See page Engine / Hybrid System>2TR-FBE ENGINE MECHANICAL>CYLINDER BLOCK>REASSEMBLY).
Do not turn the crankshaft.
Remove the 2 bolts and connecting rod cap (refer to the steps above).
| *1 | Plastigage |
| *2 | 4, 5 or 6 Mark |
Measure the Plastigage at its widest point.
0.039 to 0.066 mm (0.00154 to 0.00260 in.)
0.066 mm (0.00260 in.)
If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, inspect the crankshaft.
If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. The standard thickness of each bearing is indicated by a 4, 5 or 6 mark on its surface.
52.989 to 53.002 mm (2.086 to 2.087 in.)
| Item | Specified Condition |
|---|---|
| Mark 4 | 1.484 to 1.487 mm (0.05843 to 0.05854 in.) |
| Mark 5 | 1.488 to 1.490 mm (0.05858 to 0.05866 in.) |
| Mark 6 | 1.491 to 1.493 mm (0.05870 to 0.05878 in.) |
Completely remove the Plastigage.
Perform the inspection above for each crank pin.
3.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD
| *1 | Ridge Reamer |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
Keep the bearing, connecting rod and cap together.
Arrange the piston and connecting rod assemblies in the correct order.
4.REMOVE CONNECTING ROD BEARING
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
Arrange the removed parts in the correct order.
5.INSPECT CRANKSHAFT THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
0.02 to 0.22 mm (0.000787 to 0.00866 in.)
0.30 mm (0.0118 in.)
If the thrust clearance is more than the maximum, replace the thrust washers as a set. If necessary, replace the crankshaft.
2.440 to 2.490 mm (0.0961 to 0.0980 in.)
6.REMOVE CRANKSHAFT
Uniformly loosen the 10 bearing cap bolts in several steps in the sequence shown in the illustration.
Remove the 10 bearing cap bolts, 5 bearing caps, 5 lower bearings and 2 lower thrust washers.
Keep the lower bearings and crankshaft bearing caps together.
Arrange the thrust washers in the correct order.
Lift out the crankshaft to remove it.
Remove the upper thrust washers from the cylinder block.
Arrange the main bearing caps, bearings and thrust washers in the correct order.
7.REMOVE CRANKSHAFT BEARING
Remove the crankshaft bearings from the cylinder block and bearing caps.
Arrange the removed parts in the correct order.
8.REMOVE PISTON RING SET
Using a piston ring expander, remove the 2 compression rings.
Using a piston ring expander, remove the oil ring rail.
Remove the oil ring expander by hand.
Arrange the piston rings in the correct order.
9.REMOVE PISTON WITH PIN SUB-ASSEMBLY
Check the fitting condition between the piston and piston pin.
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
Disconnect the connecting rod from the piston.
| *1 | Snap Ring |
Using a screwdriver, pry off the snap rings from the piston.
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.
The piston and pin are a matched set.
Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.
10.CLEAN PISTON WITH PIN SUB-ASSEMBLY
Using a gasket scraper, remove the carbon from the piston top.
Using a groove cleaning tool or broken ring, clean the piston ring grooves.
Using solvent and a brush, thoroughly clean the piston.
Do not use a wire brush.
11.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY
Using a 5 mm hexagon wrench, remove the oil nozzles.
12.INSPECT BALANCE SHAFT THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance while moving the balance shaft back and forth.
0.07 to 0.13 mm (0.00276 to 0.00512 in.)
0.20 mm (0.00787 in.)
If the thrust clearance is more than the maximum, replace the balance shaft thrust washer. If necessary, replace the balance shaft.
13.REMOVE NO. 1 BALANCE SHAFT
Remove the bolt.
Remove the balance shaft from the cylinder block.
When removing the balance shaft, be sure to support the balance shaft with both hands and avoid scratching the balance shaft bearing on the cylinder block.
14.REMOVE NO. 1 BALANCE SHAFT DRIVEN GEAR
| *1 | No. 1 Balance Shaft Driven Gear |
| *2 | Sliding Key |
| *3 | Balance Shaft Thrust Washer |
| *4 | Balance Shaft Thrust Spacer |
Mount the head portion of the balance shaft in a vise.
Do not damage the balance shaft.
Remove the bolt.
Remove the No. 1 balance shaft driven gear, sliding key, balance shaft thrust washer and balance shaft thrust spacer.
15.REMOVE NO. 2 BALANCE SHAFT
Remove the 2 bolts.
Remove the balance shaft from the cylinder block.
When removing the balance shaft, be sure to support the balance shaft with both hands and avoid scratching the balance shaft bearing on the cylinder block.
16.REMOVE NO. 2 BALANCE SHAFT DRIVEN GEAR
| *1 | No. 2 Balance Shaft Driven Gear |
| *2 | No. 2 Balance Shaft Thrust Washer |
Mount the head portion of the balance shaft in a vise.
Do not damage the balance shaft.
Remove the bolt.
Remove the No. 2 balance shaft driven gear and No. 2 balance shaft thrust washer.
17.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Remove the water drain cock sub-assembly from the cylinder block.
Remove the water drain cock plug from the water drain cock sub-assembly.
18.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.