Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CAMSHAFT › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052206 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 6.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 7.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A076530

Turn the crankshaft pulley, and align the notch with timing mark 0 of the timing chain cover.


b.
A301899
2.458,0.896 2.292,0.229 2.292,0.229 0.938,0.906 true 2.563,1.344 1.771,2.271 1.771,2.271 0.875,1.219 true 1.115,3.698 1.625,4.406 1.625,4.406 0.99,3.708 true 2.51,3.552 1.615,4.406 true 2.469,3.115 2.646,2.542 2.646,2.542 1.073,3.177 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *A 0.083,2.333 0.396,2.531 0.313,0.198 10 false *B 2.292,0.052 2.604,0.25 0.313,0.198 10 false *1 1.75,2.313 2.031,2.51 0.281,0.198 10 false *1 2.646,2.385 2.854,2.615 0.208,0.229 10 false *1 1.552,4.469 1.865,4.667 0.313,0.198 10 false *1
*A for Bank 1
*B for Bank 2
*1 Timing Mark


Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

If the timing marks are not aligned, turn the crankshaft 1 complete revolution (360°) and align the timing marks as described above.


c.
A301910
1.76,0.448 3.021,0.26 3.021,0.26 2.875,1.073 true 2.969,1.281 1.833,1.958 1.833,1.958 2.813,1.292 true 1.833,1.958 1.75,0.625 true 3,0.135 3.313,0.333 0.313,0.198 10 false *1 1.667,1.958 1.979,2.156 0.313,0.198 10 false *2
*1 Paint Mark
*2 Timing Mark


Place paint marks on the No. 1 chain links that correspond with the timing marks of the camshaft timing gears.


Hide 8.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

Never rotate the crankshaft with the chain tensioner removed.

·

Before rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from TDC first.



a.
A076506

Remove the 4 bolts, timing chain cover plate and gasket.


b.
A301911
1.177,1.823 1.177,1.531 1.177,1.531 0.969,1.24 true 2.802,1.792 2.802,1.5 2.802,1.5 2.594,1.208 true 1.448,0.708 1.76,0.906 0.313,0.198 10 false *a 1.115,1.896 1.427,2.094 0.313,0.198 10 false *1 2.74,1.875 3.052,2.073 0.313,0.198 10 false *1
*1 Stopper Plate
*a Push


While turning the stopper plate of the tensioner clockwise, push in the plunger of the No. 1 chain tensioner as shown in the illustration.


c.

While turning the stopper plate of the tensioner counterclockwise, insert a bar with a diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate in place.


d.

Remove the 2 bolts and No. 1 chain tensioner.


Hide 9.REMOVE NO. 2 CAMSHAFT

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


a.
A301912
2.135,1.146 2.448,1.344 0.313,0.198 10 false *a
*a Raise


While raising the No. 2 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.


b.
G038068
0.094,0.333 0.271,0.51 0.177,0.177 10 false *a
*a Hold


Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the camshaft timing sprocket set bolt.

NOTICE:

Be careful not to damage the cylinder head and valve lifter with the wrench.



c.

Separate the camshaft timing sprocket from the No. 2 camshaft.


d.
G038069

Rotate the camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face upward as shown in the illustration.


e.
A301913
0.781,1.969 0.938,2.167 0.156,0.198 10 false 1 1.479,1.969 1.635,2.167 0.156,0.198 10 false 3 2.167,1.979 2.323,2.177 0.156,0.198 10 false 7 2.375,1.979 2.531,2.177 0.156,0.198 10 false 5 0.792,1.094 0.948,1.292 0.156,0.198 10 false 2 1.479,1.094 1.635,1.292 0.156,0.198 10 false 4 2.156,1.094 2.313,1.292 0.156,0.198 10 false 8 2.427,1.031 2.583,1.229 0.156,0.198 10 false 6

Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.


f.

Remove the 4 bearing caps and No. 2 camshaft.


Hide 10.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
G038070

Remove the No. 2 chain tensioner bolt, and then remove the No. 2 chain tensioner and camshaft timing sprocket.


Hide 11.REMOVE CAMSHAFT

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


a.
G038072
0.688,0.115 0.854,0.313 0.167,0.198 10 false *a
*a Hold


Hold the hexagonal portion of the camshaft with a wrench and loosen the camshaft timing gear set bolt.

NOTICE:
·

Be careful not to damage the cylinder head and valve lifter with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




b.
G038071
2.49,1.188 2.552,1.229 false
V100135

Slide


Slide the camshaft timing gear and separate the chain from the camshaft timing gear.


c.
G038073

Rotate the camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face downward as shown in the illustration.


d.
A301914
0.792,0.479 0.948,0.677 0.156,0.198 10 false 1 1.469,0.469 1.625,0.667 0.156,0.198 10 false 3 2.146,0.469 2.302,0.667 0.156,0.198 10 false 7 2.542,0.385 2.698,0.583 0.156,0.198 10 false 5 0.781,1.385 0.927,1.583 0.146,0.198 10 true 2 1.479,1.375 1.635,1.573 0.156,0.198 10 true 4 2.146,1.396 2.302,1.594 0.156,0.198 10 true 8 2.531,1.458 2.688,1.656 0.156,0.198 10 true 6

Using several steps, loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.


e.

Remove the 4 bearing caps.


f.
G038074

Remove the camshaft timing gear set bolt with the camshaft lifted up, and then remove the camshaft and camshaft timing gear together with the No. 2 chain.


g.
A076517

Tie the chain with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover.



Hide 12.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


a.
G038075
1.979,0.26 2.156,0.458 0.177,0.198 10 false *a
*a Push


While pushing down the No. 3 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.


b.

Hold the hexagonal portion of the No. 4 camshaft with a wrench and remove the camshaft timing sprocket set bolt.

NOTICE:

Be careful not to damage the cylinder head and valve lifter with the wrench.



c.

Separate the camshaft timing sprocket from the No. 4 camshaft.


d.
A301916
0.792,0.906 0.948,1.094 0.156,0.188 10 true 6 1.292,1.01 1.458,1.188 0.167,0.177 10 true 8 1.948,1.01 2.125,1.198 0.177,0.188 10 true 4 2.625,0.99 2.781,1.188 0.156,0.198 10 true 2 0.781,1.979 0.938,2.177 0.156,0.198 10 false 5 1.292,1.917 1.448,2.115 0.156,0.198 10 false 7 1.958,1.938 2.115,2.135 0.156,0.198 10 false 3 2.635,1.938 2.792,2.135 0.156,0.198 10 false 1

Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.


e.

Remove the 4 bearing caps and No. 4 camshaft.


Hide 13.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
G038077

Remove the No. 3 chain tensioner bolt, and then remove the No. 3 chain tensioner and camshaft timing sprocket.


Hide 14.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


a.
A076484
1.365,1.75 1.354,1.792 false
V100135

Slightly Turn


Release the chain tension between the camshaft timing gear (LH bank) and crankshaft timing gear by turning the crankshaft pulley counterclockwise slightly.


b.

Hold the hexagonal portion of the No. 3 camshaft with a wrench and loosen the camshaft timing gear set bolt.

NOTICE:
·

Be careful not to damage the cylinder head and valve lifter with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




c.
G038401
0.844,1.229 0.917,1.198 false
V100135

Slide


Slide the camshaft timing gear and separate the chain from the camshaft timing gear.


d.
A301917
0.833,0.292 0.99,0.49 0.156,0.198 10 false 5 1.333,0.385 1.5,0.573 0.167,0.188 10 false 7 1.979,0.375 2.146,0.563 0.167,0.188 10 false 3 2.635,0.375 2.802,0.563 0.167,0.188 10 false 1 0.833,1.438 0.99,1.635 0.156,0.198 10 false 6 1.344,1.354 1.5,1.552 0.156,0.198 10 false 8 1.979,1.385 2.135,1.583 0.156,0.198 10 false 4 2.625,1.375 2.781,1.573 0.156,0.198 10 false 2

Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.


e.

Remove the 4 bearing caps.


f.
G038402

Remove the camshaft timing gear set bolt with the No. 3 camshaft lifted up, and then remove the No. 3 camshaft and camshaft timing gear together with the No. 2 chain.


g.
A076489

Tie the chain with a string as shown in the illustration.

NOTICE:

Be careful not to drop anything inside the timing chain cover.