Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › from 2012.04
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052209 REAR CRANKSHAFT OIL SEAL A

1GR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.

Apply MP grease to the lip of a new rear crankshaft oil seal.


b.
A302006
1.99,0.969 2.573,1.427 2.573,1.427 2.792,1.427 true 2.854,1.323 3.313,1.521 0.458,0.198 10 false SST

Using SST and a hammer, tap in the rear crankshaft oil seal until its surface is flush with the rear oil seal retainer edge.

SST
09223-78010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the oil seal at an angle.




Hide 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A302004
1.948,0.74 2.469,0.74 2.469,0.74 2.469,1.521 true 0.938,1.51 2.677,1.521 true 2.74,1.427 3.042,1.594 0.302,0.167 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A302007
0.521,1.25 0.844,1.25 false 1.313,1.281 1.635,1.281 false 2.125,1.188 2.448,1.188 false 0.344,1.135 0.656,1.292 0.313,0.156 10 false *1 1.146,1.156 1.458,1.313 0.313,0.156 10 false *2 1.969,1.094 2.281,1.25 0.313,0.156 10 false *3
*1 Front Spacer
*2 Drive Plate and Ring Gear
*3 Rear Spacer
V100135

Automatic Transmission Side


Install the front spacer, drive plate and ring gear and rear spacer to the crankshaft.

HINT:

As the front spacer, drive plate and ring gear and rear spacer are not reversible, be sure to install them in the direction shown in the illustration.



c.

Clean the bolts and bolt holes.


d.
P000601
1.979,1.177 2.177,0.25 2.177,0.25 2.302,0.25 false 2.375,0.156 2.573,0.344 0.198,0.188 10 false *1
*1 Adhesive


Apply adhesive to 2 or 3 threads at the ends of the new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A302008
1.677,0.188 1.833,0.385 0.156,0.198 10 false 1 2.302,0.406 2.458,0.604 0.156,0.198 10 false 5 2.542,1.021 2.698,1.219 0.156,0.198 10 false 3 2.26,1.667 2.417,1.865 0.156,0.198 10 false 7 1.688,1.885 1.844,2.083 0.156,0.198 10 false 2 1.063,1.677 1.219,1.875 0.156,0.198 10 false 6 0.781,1.063 0.938,1.26 0.156,0.198 10 false 4 1.052,0.417 1.208,0.615 0.156,0.198 10 false 8

Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.