Home › Engine / Hybrid System › 2TR-FBE FUEL › FUEL INJECTOR › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009581 2TR-FBE FUEL _0052250 FUEL INJECTOR A

2TR-FBE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL INJECTOR ASSEMBLY

a.
A099091
2.313,0.708 2.625,0.708 false 1.323,1.875 1.854,1.74 1.854,1.74 2.063,1.74 false 2.656,0.635 2.854,0.823 0.198,0.188 10 false *1 2.094,1.656 2.281,1.823 0.188,0.167 10 false *2
*1 New O-Ring
*2 New Insulator


Install a new insulator to the fuel injector.


b.

Apply a light coat of grease or gasoline to a new O-ring and install it to the fuel injector.


c.
A099091
2.313,0.708 2.625,0.708 false 1.323,1.875 1.854,1.74 1.854,1.74 2.063,1.74 false 2.656,0.635 2.854,0.823 0.198,0.188 10 false *1 2.094,1.656 2.281,1.823 0.188,0.167 10 false *2
V100135

New O-Ring
V100136

New Insulator


Apply a light coat of grease or gasoline on the place where the delivery pipe touches the O-ring.


d.

To install the fuel injector into the fuel delivery pipe, push the fuel injector while twisting it back and forth.

NOTICE:
·

Be careful not to twist the O-ring.

·

After installing the fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.




e.

Position the fuel injector connector so that it faces downward.


Hide 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Apply a light coat of gasoline or spindle oil to new O-rings, and then install one to each spacer.


b.
G036023

Install the 4 spacers to the cylinder head.


c.

Install 4 new injector vibration insulators to the cylinder head.


d.

Install the 2 No. 1 delivery pipe spacers to the cylinder head.


e.

Install the fuel delivery pipe together with the 4 fuel injectors with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not drop the fuel injectors when installing the fuel delivery pipe.



f.

Connect the 4 injector connectors.


g.

Connect the 4 clamps and wire harness to the delivery pipe.


h.

Connect the vacuum hose.


Hide 3.CONNECT NO. 2 FUEL HOSE

a.

Connect the No. 2 fuel hose.


Hide 4.CONNECT NO. 1 FUEL HOSE

a.

Connect the No. 1 fuel hose (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 5.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 6.CONNECT CABLE TO BATTERY NEGATIVE TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 7.INSPECT FOR FUEL LEAK (for Fuel Main Tank)

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON and turn the intelligent tester on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

iv.

Check that there are no leaks from the fuel system.

If there are fuel leaks, repair or replace parts as necessary.


v.

Turn the ignition switch off.


vi.

Disconnect the intelligent tester from the DLC3.