Home › Engine / Hybrid System › 2TR-FBE FUEL › FUEL TANK › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009581 2TR-FBE FUEL _0052259 FUEL TANK A

2TR-FBE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 5.REMOVE NO. 1 FUEL TANK PROTECTOR

a.

Remove the 4 nuts and No. 1 fuel tank protector.


Hide 6.REMOVE NO. 3 FUEL TUBE CLAMP

a.
G038853

Remove the tube clamp from the fuel tube.


Hide 7.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE

a.
A302994
1.531,0.854 1.49,0.698 1.49,0.698 1.385,0.698 true 1.885,0.969 1.656,0.292 1.656,0.292 1.552,0.292 true 2.406,1.156 2.677,1.615 2.677,1.615 2.75,1.615 false 1.229,0.604 1.542,0.802 0.313,0.198 10 false *1 1.385,0.219 1.698,0.417 0.313,0.198 10 false *2 2.802,1.542 3.115,1.74 0.313,0.198 10 false *3
*1 Fuel Main Tube
*2 Fuel Return Tube
*3 Vent Line Hose


Disconnect the fuel tank main tube (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Disconnect the fuel tank return tube (See page Engine / Hybrid System>2TR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


c.

Disconnect the vent line hose.


Hide 8.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A099799

Disconnect the fuel tank to filler pipe hose from the fuel tank inlet pipe.


Hide 9.DISCONNECT FUEL TANK BREATHER HOSE

a.

Disconnect the fuel tank breather hose from the fuel tank inlet pipe.


Hide 10.REMOVE FUEL TANK INLET PIPE SUB-ASSEMBLY

a.

Remove the bolt and fuel tank inlet pipe.


Hide 11.REMOVE FUEL TANK ASSEMBLY

a.
A099811

Place an engine lifter under the fuel tank.


b.

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


c.

Slightly lower the engine lifter.

NOTICE:

Be careful not to cut the wiring.



d.
A252100
2.427,3.146 1.917,3.146 false 1.583,4.104 1.208,4.104 false 2.479,3.052 2.656,3.219 0.177,0.167 10 false *1 2.25,3.885 2.427,4.052 0.177,0.167 10 false *3 0.979,4.021 1.156,4.188 0.177,0.167 10 false *2
*1 Fuel Tank Cushion
*2 Wire Harness
*3 Fuel Tank


Remove the clip. Then fold back approximately half of each cushion rubber so that the wire harness can be removed in the step below.


e.
A303015
1.094,1.219 1.25,1.417 0.156,0.198 10 false A 1.771,1.542 1.927,1.74 0.156,0.198 10 false A 2.021,0.958 2.177,1.156 0.156,0.198 10 false A

Detach the wire harness from the 6 clamps shown in the illustration.

HINT:

Detach the claws of the clamps labeled A in the illustration to detach the wire harness.



f.

Disconnect the fuel pump and sender gauge connector.


Hide 12.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A303016
0.729,3.354 0.875,3.156 0.875,3.156 1.01,3.156 false 0.563,2.844 0.719,3.042 0.156,0.198 10 false 1 1.677,2.844 1.833,3.042 0.156,0.198 10 false 2 2.802,2.844 2.958,3.042 0.156,0.198 10 false 3 1.073,3.052 1.229,3.25 0.156,0.198 10 false *1
*1 Needle-nose Pliers
V100135

Clip
V100136

Nut


Using needle-nose pliers, remove the 4 clips and nut as shown in the illustration, and then remove the No. 1 fuel tank heat insulator.


Hide 13.REMOVE NO. 1 FUEL TANK CUSHION

a.
A252103

Remove the clip and 2 fuel tank cushions from the fuel tank.


Hide 14.REMOVE VENT LINE TUBE

a.

Disconnect the vent line hose and remove the vent line tube.


Hide 16.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 17.REMOVE NO. 2 FUEL TANK PROTECTOR

a.
A252108

Detach the 2 claws and remove the protector.


Hide 18.REMOVE FUEL TANK BREATHER HOSE

a.

Remove the fuel tank breather hose from the fuel tank.


Hide 19.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.

Remove the fuel tank to filler pipe hose from the fuel tank.