Home › Engine / Hybrid System › 2TR-FBE FUEL › FUEL SUB TANK › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009581 2TR-FBE FUEL _0052260 FUEL SUB TANK A

2TR-FBE FUEL  FUEL SUB TANK  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BREATHER TUBE FUEL HOSE

a.
A241615
1.385,1.625 0.823,1.625 true 2.125,0.458 1.875,0.458 1.875,0.458 1.458,1.458 true 2.188,0.354 2.365,0.531 0.177,0.177 10 false *1 0.625,1.531 0.802,1.708 0.177,0.177 10 false *2
*1 Paint Mark (Yellow)
*2 Protrusion


Align the paint mark and protrusion as shown in the illustration and install the breather tube fuel hose, and then tighten the hose clamp in the position shown in the illustration.


Hide 2.INSTALL FUEL TANK FILLER PIPE

a.
A241614
2.021,0.552 1.865,0.552 1.865,0.552 1.333,0.667 true 2.188,0.146 1.948,0.146 1.948,0.146 1.302,0.573 true 2.094,0.469 2.26,0.635 0.167,0.167 10 false *1 2.26,0.052 2.469,0.229 0.208,0.177 10 false *2
*1 Paint Mark (Blue)
*2 Protrusion


Align the protrusion and paint mark as shown in the illustration and install the fuel tank filler pipe, and then tighten the hose clamp in the position shown in the illustration.


Hide 7.INSTALL FUEL TANK CAP COVER

a.

Install the fuel tank cap cover with a new tie wrap.


Hide 8.INSTALL FUEL TANK CAP ASSEMBLY

Hide 9.INSTALL FUEL TANK FILLER PIPE SUPPORT

a.
A239224

Install the No. 1 fuel tank filler pipe support and No. 2 fuel tank filler pipe support as shown in the illustration.


Hide 10.INSTALL SOLENOID VALVE ASSEMBLY

a.

Install the solenoid valve assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the hose.


Hide 11.INSTALL AUXILIARY FUEL TANK ASSEMBLY

a.

Install the auxiliary fuel tank assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not drop the auxiliary fuel tank.

·

Do not damage the piping or wiring.




b.

Connect the No. 2 fuel tank filler tube.


c.

Connect the fuel pump connector.


d.

Connect the No. 4 fuel hose.


e.

Connect the fuel sender gauge connector.


f.

Connect the connector and No. 3 fuel hose.


Hide 12.ADD FUEL

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 14.INSPECT FOR FUEL LEAK (for Fuel Sub Tank)

a.

Start the engine.

NOTICE:

Perform the inspection while the engine is cold.

The fuel pump operates only for a calculated time when the coolant temperature is 20°C (68°F) or less and learned ethanol concentration is 85% or more.



b.

Check for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.