Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL SYSTEM › from 2012.04
RM1840EF _51 Engine / Hybrid System _009582 1GR-FE FUEL _0052263 FUEL SYSTEM L

1GR-FE FUEL  FUEL SYSTEM  PRECAUTION  


PRECAUTION


a.

Before starting work on the fuel system, including inspections and repairs, disconnect the cable from the negative (-) battery terminal.


b.

Do not smoke or work near fire when performing work on the fuel system.


c.

Keep gasoline away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Take precautions to prevent gasoline from spilling out before removing fuel system parts.

·

Pressure still remains in the fuel lines even after performing the following procedures. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.
G038856
0.688,0.24 1.156,0.24 1.156,0.24 1.667,0.458 true 0.479,0.156 0.656,0.333 0.177,0.177 10 false *1
*1 Fuel Pump Connector


Disconnect the fuel pump connector.


b.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

DTC P0171/25 (system too lean) may be stored.



c.

Crank the engine again and check that the engine does not start.


d.

Loosen the fuel tank cap and discharge the pressure in the fuel tank completely.


e.

Connect the fuel pump connector.



FUEL SYSTEM


a.

When disconnecting a high pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.

i.

Disconnect the fuel pump tube.


ii.

Drain any fuel remaining inside the fuel pump tube.


iii.

To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.


iv.

Put a container under the connection.



b.
A133695
0.458,2.688 0.625,2.688 0.625,2.688 0.823,2.25 false 1.49,3.042 1.333,3.042 1.333,3.042 1.219,2.292 false 0.49,1.344 0.646,1.344 0.646,1.344 0.833,1.052 false 1.417,1.344 1.26,1.344 1.26,1.344 1.198,1.083 false 2.375,0.146 2.594,0.354 0.219,0.208 10 false *a 2.406,1.104 2.583,1.281 0.177,0.177 10 false *b 0.302,2.594 0.469,2.75 0.167,0.156 10 false *1 1.542,2.938 1.719,3.135 0.177,0.198 10 false *2 2.406,2.198 2.583,2.375 0.177,0.177 10 false *b 0.292,1.24 0.458,1.396 0.167,0.156 10 false *1 1.479,1.25 1.656,1.448 0.177,0.198 10 false *2
*1 O-Ring
*2 Delivery Pipe
*a CORRECT
*b INCORRECT


Observe these precautions when removing and installing the injector.

i.

Never reuse the O-ring.


ii.

When installing a new O-ring to the injector, do not damage it.


iii.

Coat new O-rings with spindle oil or gasoline before installing them. Do not use engine oil, gear oil or brake oil.



c.
A133696
2.323,0.188 2.177,0.188 2.177,0.188 1.875,0.667 false 0.854,0.667 1.313,0.667 1.313,0.667 1.615,1.146 true 1.438,1.688 0.813,1.688 false 2.833,2.281 2.833,2.073 2.833,2.073 2.021,1.76 true 1.208,2.552 0.844,2.917 0.844,2.917 0.625,2.917 true 2.375,0.094 2.583,0.271 0.208,0.177 10 false *1 2.781,2.323 2.969,2.5 0.188,0.177 10 false *4 0.625,1.583 0.792,1.75 0.167,0.167 10 false *3 0.438,2.823 0.615,3 0.177,0.177 10 false *5 0.667,0.583 0.875,0.76 0.208,0.177 10 false *2
*1 Delivery Pipe
*2 O-Ring
*3 Injector
*4 Intake Manifold
*5 Insulator


Install the injector to the delivery pipe and cylinder head as shown in the illustration.

NOTICE:

Before installing the injector, apply spindle oil or gasoline to the area where the delivery pipe contacts the O-ring of the injector.



d.

Observe these precautions when disconnecting the fuel tube connector.

i.
A099426
1.031,1.5 1.563,1.5 false 0.823,1.396 0.99,1.594 0.167,0.198 10 false *1
*1 Fuel Pipe Clamp


for Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.


ii.
A223364
1.135,0.698 1.24,0.698 1.24,0.698 1.563,1.01 false 0.948,0.615 1.135,0.802 0.188,0.188 10 false *1
*1 Fuel Hose Connector Cover


for Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover as shown in the illustration.


iii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iv.
A088336
1.563,1.573 1.573,1.656 false
V100135

Pinch
V100136

Pull


If the connector and the pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:
·
A224870
0.833,0.198 0.698,0.198 0.698,0.198 0.573,0.813 true 2.469,0.208 2.354,0.208 2.354,0.208 2.208,0.865 false 1.323,1.333 1.323,1.781 true 1.469,1.781 1.094,1.781 1.094,1.781 1.094,1.333 true 1.813,1.354 2.063,1.76 2.063,1.76 2.177,1.76 false 0.271,1.771 0.177,1.771 0.177,1.771 0.177,1.573 false 0.177,1.563 0.25,1.271 false 0.875,0.104 1.063,0.281 0.188,0.177 10 false *1 2.229,1.667 2.417,1.844 0.188,0.177 10 false *5 1.531,1.688 1.719,1.865 0.188,0.177 10 false *4 2.531,0.135 2.719,0.313 0.188,0.177 10 false *2 0.344,1.688 0.531,1.865 0.188,0.177 10 false *3
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Fuel Tube Connector


Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




v.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


vi.

To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.



e.

Observe these precautions when connecting the fuel tube connector.

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.
A302842
1.938,1.021 1.969,1.052 false
V100135

Push


Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a little amount of fresh engine oil on the tip of the pipe.


iii.
A302843
1.906,1.01 1.958,1.063 false
V100135

Pull


After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.


iv.

for Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the fuel tube connector.


v.

for Fuel Hose Connector Cover Type:

Attach the lock claws to the connector by pushing down on the connector cover.


vi.

Check for any fuel leaks.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).