Home › Engine / Hybrid System › 2KD-FTV EMISSION CONTROL › VACUUM SWITCHING VALVE(w/o DPF)
RM1840EF _51 Engine / Hybrid System _009583 2KD-FTV EMISSION CONTROL _0052277 VACUUM SWITCHING VALVE(w/o DPF) G

2KD-FTV EMISSION CONTROL  VACUUM SWITCHING VALVE(w/o DPF)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT VACUUM SWITCHING VALVE (for EGR Cut)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 37 to 44 Ω
1 - Body ground
2 - Body ground
20°C (68°F) 10 kΩ or higher


If the result is not as specified, replace the vacuum switching valve.


b.

Check operation of the vacuum switching valve.

i.
A151248
2.406,2.75 2.281,2.75 2.281,2.75 2.01,2.313 false 0.865,1.167 0.99,1.167 0.99,1.167 1.427,1.938 true 2.448,2.667 2.625,2.813 0.177,0.146 10 false *2 0.667,1.094 0.844,1.24 0.177,0.146 10 false *1
*1 Port E
*2 Filter


Attach a vacuum pump to port E and check that vacuum does not flow from the filter to port E.


ii.
A151249
2.542,2.917 2.542,2.417 true 0.625,2.125 0.708,2.125 0.708,2.125 1.344,1.927 true 0.625,2.573 0.708,2.573 0.708,2.573 1.438,1.979 true 2.396,1.729 2.292,1.729 2.292,1.729 1.99,2.125 true 2.469,2.938 2.656,3.083 0.188,0.146 10 false *2 0.49,2.042 0.615,2.188 0.125,0.146 10 false 1 0.49,2.479 0.615,2.625 0.125,0.146 10 false 2 2.406,1.646 2.594,1.792 0.188,0.146 10 false *1
*1 Port E
*2 Filter


Apply battery voltage across terminals 1 and 2.


iii.

Attach a vacuum pump to port E and check that vacuum flows from the filter to port E.

If the result is not as specified, replace the vacuum switching valve.



Hide 2.INSPECT VACUUM SWITCHING VALVE (for EGR Bypass Valve)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 37 to 44 Ω
1 - Body ground
2 - Body ground
20°C (68°F) 10 kΩ or higher


If the result is not as specified, replace the vacuum switching valve.


b.
A222591
1.583,2.438 1.76,1.792 1.76,1.792 1.813,1.792 true 1.396,2.688 0.906,2.688 true 2.646,2.677 2.792,2.802 2.792,2.802 2.854,2.802 false 0.688,2.615 0.854,2.771 0.167,0.156 10 false *2 0.458,1.542 0.625,1.698 0.167,0.156 10 false *a 0.969,0.969 1.135,1.125 0.167,0.156 10 false *b 2.865,2.708 3.031,2.865 0.167,0.156 10 false *3 1.823,1.708 1.99,1.865 0.167,0.156 10 false *1
*1 Port E
*2 Port F
*3 Filter
*a Air
*b Vacuum


Check operation of the vacuum switching valve.

i.

When a vacuum of 67 kPa (500 mmHg, 19.7 in.Hg) is applied to port F, check that air flows from port E to the filter.


ii.
A222592
1.406,1.156 1.635,0.229 1.635,0.229 1.458,0.229 true 1.26,1.292 0.771,1.292 true 1.854,0.719 2.135,0.25 2.135,0.25 2.01,0.25 true 1.969,0.76 2.208,0.854 2.208,0.854 2.365,0.854 true 1.281,0.125 1.448,0.302 0.167,0.177 10 false *1 0.583,1.198 0.75,1.375 0.167,0.177 10 false *2 0.188,0.563 0.354,0.74 0.167,0.177 10 false *a 1.833,0.156 2,0.333 0.167,0.177 10 false 2 2.406,0.74 2.573,0.917 0.167,0.177 10 false 1
*1 Port E
*2 Port F
*a Air


Apply battery voltage across terminals 1 and 2.


iii.

Check that air flows from port E to port F.

If the result is not as specified, replace the vacuum switching valve.