Home › Engine / Hybrid System › 2KD-FTV EMISSION CONTROL › EGR VALVE(w/ DPF) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009583 2KD-FTV EMISSION CONTROL _0052278 EGR VALVE(w/ DPF) G

2KD-FTV EMISSION CONTROL  EGR VALVE(w/ DPF)  INSPECTION  


PROCEDURE

Hide 1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A240557
1.323,1.5 1.323,1.875 true 0.938,1.51 0.938,1.885 true 0.031,0.01 0.219,0.167 0.188,0.156 10 false *a 2.458,1.281 2.573,1.438 0.115,0.156 10 false 1 2.063,1.281 2.177,1.438 0.115,0.156 10 false 2 1.667,1.281 1.781,1.438 0.115,0.156 10 false 3 1.271,1.281 1.385,1.438 0.115,0.156 10 false 4 0.885,1.281 1,1.438 0.115,0.156 10 false 5 1.25,1.917 1.479,2.073 0.229,0.156 10 false M+ 0.865,1.917 1.094,2.073 0.229,0.156 10 false M-
*a Component without harness connected
(Electric EGR Control Valve)


Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
5 (M-) - 4 (M+) 25°C (77°F) 0.3 to 100 Ω

HINT:

The temperature indicated under "Condition" is the temperature of the electric EGR control valve assembly.


If the result is not as specified, replace the electric EGR control valve assembly.


Hide 2.VISUAL CHECK ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

Visually check the electric EGR control valve for deposits.

If there are deposits, clean the electric EGR control valve.

NOTICE:
·

When cleaning the electric EGR control valve, make sure the valve is completely closed.

·

Do not forcibly open the valve as it may be damaged or deformed.

·

When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto this part or soaking the part in solvent may damage the part.




b.
A302579
2.625,3.198 2.625,2.615 2.625,2.615 2.802,2.615 true 2.51,3.823 2.427,4.333 2.427,4.333 2.271,4.333 true 0.74,2.823 0.74,3.292 true 0.677,2.594 0.833,2.792 0.156,0.198 10 false A 0.906,4.198 1.094,4.396 0.188,0.198 10 false *a 2.854,2.521 3.052,2.708 0.198,0.188 10 false *1 2.063,4.24 2.26,4.427 0.198,0.188 10 false *1 2.594,4.208 2.823,4.417 0.229,0.208 10 false *b
*1 Gap
*a CORRECT
*b INCORRECT


Hold the electric EGR control valve up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.

HINT:

Light passes through part A shown in the illustration even if the valve is completely closed. This is not a problem.