Home › Engine / Hybrid System › 2KD-FTV EMISSION CONTROL › EGR COOLER(w/ DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009583 2KD-FTV EMISSION CONTROL _0052279 EGR COOLER(w/ DPF) A

2KD-FTV EMISSION CONTROL  EGR COOLER(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 6.REMOVE FRONT WHEEL LH

Hide 7.REMOVE FRONT FENDER APRON SEAL UPPER

a.

Remove the 5 clips and front fender apron seal upper.


Hide 8.REMOVE FRONT FENDER SEAL

a.

Remove the 5 clips and front fender seal.


Hide 9.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A252236

Detach the wire harness clamp.


c.

Remove the bolt and engine oil level dipstick guide.


d.

Remove the O-ring from the engine oil level dipstick guide.


Hide 10.DISCONNECT WATER BY-PASS HOSE

a.

Disconnect the 6 water by-pass hoses.

A252237


Hide 11.REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

a.

Disconnect the vacuum switching valve connector.


b.

Disconnect the 2 vacuum transmitting hoses.


c.
A252239

Remove the 2 bolts and manifold stay with vacuum switching valve.


Hide 12.REMOVE NO. 3 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A252240

Remove the 3 bolts and No. 3 cylinder head cover.


Hide 13.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

a.
A252241

Remove the bolt and No. 2 injection pipe clamp.


b.

Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


Hide 14.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
·

After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.

·

After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



a.
A252242

Disconnect the 4 injector connectors and electric EGR control valve connector.


b.

Detach the 2 wire harness clamps.


c.
A252243

Remove the 4 nuts and 2 No. 3 injection pipe clamps.


d.
A252244
0.063,0.104 0.302,0.271 0.24,0.167 10 true *a 0.104,2.375 0.385,2.573 0.281,0.198 10 true *b
*a Injector Side
*b Common Rail Side


Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


Hide 15.REMOVE NO. 5 WATER BY-PASS PIPE

a.
A252245

Detach the 2 wire harness clamps.


b.
A252246

Disconnect the 2 water hoses from the electric EGR control valve.


c.

Remove the 2 bolts and No. 5 water by-pass pipe.


Hide 16.REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

a.
A252248

Disconnect the manifold absolute pressure sensor connector and vacuum hose.


b.

Remove the bolt and manifold absolute pressure sensor.


Hide 17.REMOVE GAS FILTER BRACKET WITH GAS FILTER

a.
A252249

Disconnect the vacuum hose.


b.

Remove the bolt and gas filter bracket with gas filter.


Hide 18.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A252250

Remove the bolt and wiring harness clamp bracket.


Hide 19.REMOVE THROTTLE BODY BRACKET

a.
A252251

Remove the 3 bolts and throttle body bracket.


Hide 20.DISCONNECT ENGINE WIRE

a.
A252252

Detach the 2 wire harness clamps.


b.

Remove the bolt and disconnect the engine wire.


Hide 21.DISCONNECT NO. 3 WATER BY-PASS PIPE

a.
A252253

Remove the 2 bolts and disconnect the No. 3 water by-pass pipe.


Hide 22.REMOVE EGR VALVE BRACKET

a.
A252254

Remove the 3 bolts and EGR valve bracket.


Hide 23.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

a.
A252255

Disconnect the fuel pressure sensor connector from the common rail.


b.

Remove the 5 bolts, 2 nuts and electric EGR control valve with No. 2 EGR valve and EGR cooler.

A252256
3.292,3.604 3.292,3.99 false 6.01,3.396 6.469,3.396 false 3.198,4.01 3.385,4.167 0.188,0.156 10 false *1 6.521,3.323 6.708,3.479 0.188,0.156 10 false *1 6.104,2.208 6.344,2.354 0.24,0.146 10 false x 3 5.25,3.823 5.49,3.969 0.24,0.146 10 false x 2 4.25,3.927 4.49,4.073 0.24,0.146 10 false x 2
*1 Gasket - -



c.

Remove the 2 gaskets from the cylinder head and intake manifold.


Hide 24.REMOVE INTAKE AIR CONNECTOR WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 26.REMOVE EGR VALVE ADAPTER

a.
A252258

Using a 6 mm hexagon wrench, remove the 3 hexagon socket head cap bolts, 3 plate washers, EGR valve adapter and gasket.


Hide 27.REMOVE NO. 2 EGR VALVE ASSEMBLY

a.
A252259

Remove the bolt, No. 2 EGR valve and gasket.


Hide 28.REMOVE EGR COOLER INSULATOR

a.
A252260
0.771,0.323 1.188,0.323 false 2.021,0.208 2.438,0.208 false 1.198,0.24 1.385,0.396 0.188,0.156 10 false *1 1.823,0.115 2.01,0.271 0.188,0.156 10 false *2
*1 No. 2 EGR Cooler Insulator
*2 No. 1 EGR Cooler Insulator


Remove the 2 EGR cooler insulators from the EGR cooler.