Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD(w/o Glow Plug Controller)
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052325 INTAKE MANIFOLD(w/o Glow Plug Controller) G

1KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/o Glow Plug Controller)  INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE MANIFOLD

NOTICE:

Do not adjust the adjusting screw or 2 actuator installation bolts.

A260052
0.406,0.083 0.729,0.375 0.323,0.292 10 false *A 3.979,0.073 4.219,0.406 0.24,0.333 10 false *B
*A w/ EGR Cooler *B w/o EGR Cooler



a.

Disconnect the vacuum hose from the actuator.


b.

w/ EGR Cooler:

i.

Check the operation of the swirl control valve.

A149795


ii.

Check that the valve is fully opened under normal conditions.


iii.

Connect the vacuum pumps as shown in the illustration. First apply negative pressure to the diaphragm closer to the intake manifold. This will cause the actuator rod to move, which causes the swirl control valve to move. Then, apply negative pressure to the diaphragm on the outer side. This will cause the actuator rod to move further, which also causes the swirl control valve to move further. Check that the valve is fully closed when a negative pressure of 35 kPa (263 mmHg, 10 in.Hg) is applied.


iv.

Leave it for 1 minute and check that the vacuum pump needle does not move. If the result is not as specified, replace the intake manifold.



c.

w/o EGR Cooler:

i.
A149796

Check the operation of the swirl control valve.


ii.

Check that the valve is fully opened under normal conditions.


iii.

Connect a vacuum pump to the control valve. Check that the valve is fully closed when a negative pressure of 35 kPa (263 mmHg, 10 in.Hg) is applied.


iv.

Leave it for 1 minute and check that the vacuum pump needle does not move.

If the result is not as specified, replace the intake manifold.



Hide 2.INSPECT VACUUM SWITCHING VALVE (for Swirl Control Valve)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 33 to 39 Ω
1 - Body ground
2 - Body ground
20°C (68°F) 10 kΩ or higher


If the result is not as specified, replace in the table below.

Replace Parts
w/ EGR Cooler Vacuum Control Valve Set
w/o EGR Cooler Intake Manifold


b.

Check the operation according to the value(s) in the table below.

A301692
1.573,1.083 1.354,0.729 1.354,0.729 1.167,0.729 true 0.76,1.615 0.552,1.24 0.552,1.24 0.396,1.24 false 4.74,1.5 4.521,1.146 4.521,1.146 4.333,1.146 true 5.906,1.479 6.125,1.135 6.125,1.135 6.417,1.135 false 1.01,0.635 1.323,0.833 0.313,0.198 10 false *1 0.24,1.135 0.552,1.333 0.313,0.198 10 false *2 4.177,1.052 4.49,1.25 0.313,0.198 10 false *1 6.458,1.031 6.771,1.229 0.313,0.198 10 false *2 0.198,0.073 0.51,0.271 0.313,0.198 10 false *A 4.104,0.104 4.417,0.302 0.313,0.198 10 false *B
*A w/ EGR Cooler *B w/o EGR Cooler
*1 Port E *2 Filter
V100135

Airflow - -


i.

Check that air flows from port E to the filter.

If the result is not as specified, replace in the table below.

Replace Parts
w/ EGR Cooler Vacuum Control Valve Set
w/o EGR Cooler Intake Manifold


ii.

Apply battery voltage across the terminals.

A260056
1.396,1.24 0.833,1.313 0.833,1.313 0.698,1.313 true 1.458,1.344 1,1.479 1,1.479 0.875,1.479 true 1.833,1.583 1.594,2.208 1.594,2.208 1.594,2.281 true 1.885,1.635 1.885,2.396 true 1.938,1.031 2.021,0.354 2.021,0.354 2.115,0.354 true 2.375,1.417 2.656,1.771 2.656,1.771 2.781,1.771 true 2.521,1.365 2.865,1.552 2.865,1.552 2.99,1.552 false 5.354,1.323 5.521,0.573 5.521,0.573 5.646,0.573 false 5.417,1.375 5.708,0.865 5.708,0.865 5.833,0.865 true 4.552,1.708 4.323,1.656 4.323,1.656 4.198,1.656 false 4.813,1.594 4.938,1.5 4.938,1.5 5.021,1.5 false 2.073,0.99 2.594,0.99 false 2.135,0.25 2.396,0.5 0.26,0.25 10 false *1 0.729,1.385 0.885,1.552 0.156,0.167 10 false 2 1.552,2.313 1.75,2.521 0.198,0.208 10 false 1 0.552,1.229 0.698,1.406 0.146,0.177 10 false 1 1.854,2.406 1.948,2.563 0.094,0.156 10 false 2 2.833,1.677 3.104,1.906 0.271,0.229 10 false *1 2.646,0.896 2.917,1.135 0.271,0.24 10 false *2 3.031,1.448 3.292,1.677 0.26,0.229 10 false *2 5.865,0.771 6.021,0.958 0.156,0.188 10 false 1 5.698,0.479 5.792,0.635 0.094,0.156 10 false 2 5.052,1.406 5.208,1.563 0.156,0.156 10 false *1 4.042,1.583 4.219,1.74 0.177,0.156 10 false *2 0.448,0.104 0.625,0.26 0.177,0.156 10 false *A 4.042,0.104 4.219,0.26 0.177,0.156 10 false *B
*A w/ EGR Cooler *B w/o EGR Cooler
*1 Port E *2 Port F
V100135

Airflow - -



iii.

Check that air flows from port E to port F.

If the result is not as specified, replace in the table below.

Replace Parts
w/ EGR Cooler Vacuum Control Valve Set
w/o EGR Cooler Intake Manifold