Home › Engine / Hybrid System › 2KD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD(w/ EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009590 2KD-FTV INTAKE / EXHAUST _0052341 INTAKE MANIFOLD(w/ EGR Cooler) A

2KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/ EGR Cooler)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL INTAKE MANIFOLD

a.
A148136
0.115,2.417 0.333,2.615 0.219,0.198 10 false 1 1.313,2.771 1.51,2.958 0.198,0.188 10 false 2 0.531,2.563 0.667,2.75 0.135,0.188 10 false 3 1.115,2.729 1.281,2.969 0.167,0.24 10 false 4 0.75,2.625 0.917,2.833 0.167,0.208 10 false 5 0.313,2.49 0.479,2.698 0.167,0.208 10 false 6

Temporarily install a new gasket and the intake manifold with the 4 bolts and 2 nuts.


b.

Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:
A301693
2.365,0.813 2,0.135 2,0.135 1.875,0.135 true 1.719,0.042 2.031,0.198 0.313,0.156 10 false *1
*1 No. 1 manifold insulator


·

When installing the intake manifold, make sure that the No. 1 manifold insulator is not pinched.

·

Make sure that the swirl control valve actuator is not damaged by surrounding parts.




c.

Connect the vacuum hose and connector to the vacuum switching valve.


Hide 2.INSTALL INTAKE MANIFOLD INSULATOR

a.
A148159
1.833,3.146 1.25,3.146 true 1.719,4.125 1.125,4.125 true 1.792,3.667 1.198,3.667 true 1.01,3.563 1.177,3.708 0.167,0.146 10 false *2 1.063,3.063 1.219,3.208 0.156,0.146 10 false *1 0.927,4.031 1.104,4.177 0.177,0.146 10 false *3
*1 Intake Manifold
*2 Intake Manifold Insulator
*3 Common Rail


Install the intake manifold insulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

a.

Install the No. 3 intercooler support bracket with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 4.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 6.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE WITH NO. 2 EGR VALVE AND EGR COOLER

Hide 7.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the engine oil level dipstick guide.


b.

Apply a small amount of clean engine oil to the O-ring.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Install the injection pipe clamp with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 8.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE

a.

Install the manifold stay with vacuum switching valve with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Be sure to securely connect the vacuum transmitting hose.



b.

Connect the 3 vacuum transmitting hoses and 2 vacuum switching valve connector.


Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).