Home › Engine / Hybrid System › 2TR-FBE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM1840EF _51 Engine / Hybrid System _009591 2TR-FBE INTAKE / EXHAUST _0052352 EXHAUST MANIFOLD A

2TR-FBE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL EXHAUST MANIFOLD

a.

Install a new gasket.


b.
A303338
1.51,0.177 1.667,0.375 0.156,0.198 10 false 1 1.875,1.427 2.031,1.625 0.156,0.198 10 false 2 2.792,0.49 2.948,0.688 0.156,0.198 10 false 3 2.792,1.396 2.948,1.594 0.156,0.198 10 false 4 1.354,1.313 1.51,1.51 0.156,0.198 10 false 5 0.177,0.948 0.333,1.146 0.156,0.198 10 false 6 0.583,0.135 0.74,0.333 0.156,0.198 10 false 7 2.771,0.125 2.927,0.323 0.156,0.198 10 false 8

Install the exhaust manifold with 8 new nuts, and tighten the nuts in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 2.INSTALL MANIFOLD STAY

a.
A253335
0.854,1.833 0.906,1.844 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


Install the manifold stay with the 3 bolts.

Torque:
for bolt A : 72 N*m (730 kgf*cm, 53 ft.*lbf)
for bolt B : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for bolt C : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

40 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.


b.

Install the front exhaust pipe to the exhaust pipe support.


c.
A076194
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.302,1.792 1.521,1.969 0.219,0.177 10 false *1 3.083,0.896 3.302,1.073 0.219,0.177 10 false *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.




d.

Connect the front exhaust pipe to the exhaust manifold with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Install a new gasket and connect the front exhaust pipe to the center exhaust pipe with the 2 bolts and 2 nuts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


f.

Connect the heated oxygen sensor connector and attach the wire harness clamp.


g.

Connect the air fuel ratio sensor connector and attach the wire harness clamp.


Hide 6.INSTALL FRONT FENDER SEAL

a.

Install the front fender apron seal with the 5 clips.


Hide 7.INSTALL FRONT UPPER FENDER APRON SEAL

a.

Install the front upper fender apron seal with the 5 clips.