Home › Engine / Hybrid System › 2TR-FE COOLING › RADIATOR
RM1840EF _51 Engine / Hybrid System _009594 2TR-FE COOLING _0052369 RADIATOR A

2TR-FE COOLING  RADIATOR  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE RADIATOR BRACKET SUB-ASSEMBLY

a.
A120273

Remove the 4 bolts and 2 brackets.


Hide 2.REMOVE RADIATOR DRAIN COCK PLUG

a.

Remove the drain cock plug.


b.

Remove the O-ring.


Hide 3.ASSEMBLE SST

a.
A113337
2.833,1.094 2.427,1.698 2.427,1.698 2.333,1.698 true 2.365,0.719 2.698,0.26 2.698,0.26 2.792,0.26 false 2.25,2.781 2.448,3.042 2.448,3.042 2.542,3.042 false 0.448,2.5 0.646,2.74 0.646,2.74 0.74,2.74 false 2.823,0.167 3.052,0.333 0.229,0.167 10 false *1 2.156,1.594 2.365,1.771 0.208,0.177 10 false *2 0.365,1.323 0.542,1.479 0.177,0.156 10 false *3 2.604,2.948 2.906,3.115 0.302,0.167 10 false SST 0.802,2.656 1.104,2.823 0.302,0.167 10 false SST
*1 Part A
*2 Stopper Bolt
*3 Dimension B


Install the claw to part A of the overhaul handle as shown in the illustration.

SST
09230-01010  (09231-01010, 09231-01030)


b.

While squeezing the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

0.2 to 0.3 mm (0.00787 to 0.0118 in.)


NOTICE:

If this adjustment is not performed, the claw will be damaged.



Hide 4.UNCAULK LOCK PLATE

a.
A113338
0.635,1.021 0.885,1.469 0.885,1.469 0.969,1.469 true 1.25,0.771 1.51,0.438 1.51,0.438 1.656,0.438 false 0.771,0.688 1.042,0.188 1.042,0.188 1.156,0.188 false 1.198,0.104 1.365,0.25 0.167,0.146 10 false *1 1.708,0.354 2.042,0.51 0.333,0.156 10 false SST 1.01,1.365 1.198,1.542 0.188,0.177 10 false *2
*1 Tank
*2 Lock Plate


Using SST, squeeze the handle until stopped by the stopper bolt to release the caulking.

SST
09230-01010  (09231-01010, 09231-01030)


Hide 5.REMOVE UPPER RADIATOR TANK AND LOWER RADIATOR TANK

a.
A099699

Lightly tap the bracket of the radiator (or the connection area for the radiator hose inlet or radiator hose outlet) with a plastic-faced hammer and remove the tank.

NOTICE:

Do not tap the automatic transmission oil cooler pipe.



b.

Remove the O-ring.


Hide 6.REMOVE OIL COOLER ASSEMBLY (for Automatic Transmission)

A099700

a.

Remove the 2 cooler pipes.


b.

Remove the 2 nuts, 2 plate washers and oil cooler.


c.

Remove the 2 O-rings from the oil cooler.