Home › Engine / Hybrid System › 2TR-FE COOLING › RADIATOR
RM1840EF _51 Engine / Hybrid System _009594 2TR-FE COOLING _0052369 RADIATOR A

2TR-FE COOLING  RADIATOR  REASSEMBLY  


PROCEDURE

Hide 1.REMOVE OIL COOLER ASSEMBLY (for Automatic Transmission)

A099962
0.25,1.833 0.406,2.031 0.156,0.198 10 false A

a.

Install 2 new O-rings to the oil cooler.


b.

Install the oil cooler and 2 plate washers to the tank lower with the 2 nuts.

Torque:
8.3 N*m (85 kgf*cm, 74 in.*lbf)


c.

Install the 2 cooler pipes.

Torque:
15 N*m (150 kgf*cm, 11 ft.*lbf)

HINT:

Set the cooler pipe labeled A to the location and angle shown in the illustration.



Hide 2.INSPECT LOCK PLATE FOR DAMAGE

a.
A099690
2.698,0.115 2.813,0.115 2.813,0.115 3.188,0.646 true 0.688,0.115 0.76,0.115 0.76,0.115 1.094,0.385 false 2.052,1.292 2.417,1.667 2.417,1.667 2.51,1.667 false 0.479,0.042 0.74,0.24 0.26,0.198 10 false *1 2.542,0.021 2.854,0.24 0.313,0.219 10 false *1 2.552,1.583 2.802,1.802 0.25,0.219 10 false *2
*1 Lock Plate
*2 Core


Inspect the lock plate for damage.

If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. Correct any deformations with pliers.

Coolant will leak if the bottom of the lock plate groove is damaged or dented. Repair or replace it if necessary.

NOTICE:

The radiator can only be recaulked twice. After the second time, the radiator core must be replaced.



Hide 3.INSTALL UPPER RADIATOR TANK AND LOWER RADIATOR TANK

a.
A252179
2.313,1.271 2.615,0.844 2.615,0.844 2.708,0.844 false 2.75,0.76 3,0.948 0.25,0.188 10 *1 1.667,3 2,3.198 0.333,0.198 10 *d 2.677,3 2.948,3.167 0.271,0.167 10 *d 0.688,3 0.958,3.167 0.271,0.167 10 *c 2.188,2.01 2.479,2.188 0.292,0.177 10 *b 0.698,1.99 0.99,2.188 0.292,0.198 10 *a
*1 O-Ring
*a CORRECT
*b INCORRECT
*c Normal
*d Twisted


Check that there are no foreign objects in the lock plate groove, and then install a new O-ring. Make sure the O-ring is not twisted.

HINT:

When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.



b.

Install the tank without damaging the O-ring.


c.
A113342
2.01,0.875 2.125,0.875 2.125,0.875 2.74,1.031 false 2.219,1.365 2.323,1.365 2.323,1.365 2.74,1.271 true 0.771,0.365 1.094,0.552 0.323,0.188 10 false *a 1.802,0.792 2.052,0.938 0.25,0.146 10 false *1 2.594,0.385 2.885,0.594 0.292,0.208 10 false *b 2,1.281 2.24,1.448 0.24,0.167 10 false *2
*1 Tank
*2 Lock Plate
*a CORRECT
*b INCORRECT


Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and tank.


Hide 4.ASSEMBLE SST

a.
A234961
2.844,1.073 2.615,1.51 2.615,1.51 2.615,1.656 true 2.375,0.708 2.552,0.396 2.552,0.396 2.729,0.396 false 2.021,2.771 2.208,3.135 2.208,3.135 2.375,3.135 false 0.76,2.49 0.938,2.823 0.938,2.823 1.104,2.823 false 0.427,2.583 0.427,2.823 false 0.677,1.292 0.885,1.5 0.208,0.208 10 false *3 2.542,1.677 2.75,1.854 0.208,0.177 10 false *2 2.781,0.313 2.969,0.49 0.188,0.177 10 false *1 2.417,3.073 2.75,3.24 0.333,0.167 10 false SST 1.146,2.74 1.479,2.906 0.333,0.167 10 false SST 0.271,2.823 0.573,2.99 0.302,0.167 10 false SST
*1 Part A
*2 Stopper Bolt
*3 Dimension B


Install the punch assembly to part A of the overhaul handle as shown in the illustration.

SST
09230-01010  (09231-01010, 09231-01020)
09231-14010  


b.

While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

8.4 mm (0.331 in.)



Hide 5.CAULK LOCK PLATE

a.
A301332
0.979,2.698 1.417,2.188 1.417,2.188 1.75,2.188 true 0.854,2.813 0.052,1.729 0.052,1.729 0.354,1.729 true 1.677,3.927 2.427,3.927 true 1.813,4.417 1.938,4.417 1.938,4.417 2.354,4.125 true 0.073,0.865 0.229,1.063 0.156,0.198 10 false 1 3.271,0.854 3.427,1.052 0.156,0.198 10 false 2 1.646,0.354 1.802,0.552 0.156,0.198 10 false 3 1.667,1.354 1.823,1.552 0.156,0.198 10 false 4 0.906,0.344 1.063,0.531 0.156,0.188 10 false 5 0.906,1.344 1.063,1.542 0.156,0.198 10 false 6 2.448,0.354 2.604,0.552 0.156,0.198 10 false 7 2.458,1.344 2.615,1.542 0.156,0.198 10 false 8 1.833,2.104 2.188,2.292 0.354,0.188 10 false SST 0.406,1.646 0.615,1.802 0.208,0.156 10 false *1 1.49,3.854 1.708,4.01 0.219,0.156 10 false *2 1.625,4.354 1.844,4.51 0.219,0.156 10 false *3
*1 Stopper Bolt
*2 Tank
*3 Lock Plate


Lightly press SST against the lock plate in the order shown in the illustration. Repeat this step a few times, and then fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.

SST
09230-01010  (09231-01010, 09231-01020)
09231-14010  

NOTICE:
·
A099704
2.708,0.823 2.906,1 0.198,0.177 10 (1) 2.51,2.25 2.708,2.427 0.198,0.177 10 (1) 1.49,2.292 1.688,2.469 0.198,0.177 10 (1) 0.573,2.479 0.771,2.656 0.198,0.177 10 (1) 2.583,1.219 2.781,1.396 0.198,0.177 10 (2)

Do not press the protruding areas around the ports (1) and bracket (2).

·
A301336

Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.




b.
A099706
3.115,0.833 3.385,1.01 0.271,0.177 10 *1
*1 Lock Plate Height


Check the lock plate height after completing the caulking.

Standard lock plate height:

8.8 mm (0.346 in.)


If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


Hide 6.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the drain cock plug.


b.

Install the drain cock plug.


Hide 7.INSPECT FOR WATER LEAK

a.
A099707
1.885,0.885 2.292,1.781 2.292,1.781 2.823,1.344 true 2.115,1.854 2.438,2.01 0.323,0.156 10 false SST

Plug the inlet and outlet pipes of the radiator with SST.

SST
09230-01010  (09231-00030, 09231-00060)


b.

Using a radiator cap tester, apply pressure to the radiator.

Standard test pressure:

177 kPa (1.8 kgf/cm2, 26 psi)



c.

Submerge the radiator in water.


d.
A090282
2.344,1.042 2.698,0.75 2.698,0.75 2.802,0.75 false 1.115,0.333 1.469,0.333 true 1.677,1.823 1.792,1.823 1.792,1.823 2.177,1.625 true 2.844,0.688 3.094,0.854 0.25,0.167 10 false *2 0.906,0.26 1.125,0.417 0.219,0.156 10 false *1 1.458,1.74 1.75,1.938 0.292,0.198 10 false *3
*1 Tank
*2 Lock Plate
*3 O-Ring


Inspect for leaks.

HINT:

For radiators with resin tanks, there is clearance between the tank and lock plate where a small amount of air will remain. This air is released when the radiator is submerged in water, giving the appearance of an air leak. Before performing the water leak test, shake the radiator in the water until all air bubbles are released.



Hide 8.INSTALL RADIATOR BRACKET SUB-ASSEMBLY

a.

Install the 2 brackets with the 4 bolts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)