Home › Engine / Hybrid System › 2KD-FTV COOLING › RADIATOR
RM1840EF _51 Engine / Hybrid System _009595 2KD-FTV COOLING _0052374 RADIATOR A

2KD-FTV COOLING  RADIATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSPECT LOCK PLATE FOR DAMAGE

a.
A099690
2.75,0.115 2.823,0.115 2.823,0.115 3.188,0.646 true 0.688,0.115 0.76,0.115 0.76,0.115 1.094,0.385 false 2.042,1.292 2.406,1.667 2.406,1.667 2.5,1.667 false 0.479,0.042 0.75,0.219 0.271,0.177 10 false *1 2.521,0.031 2.781,0.219 0.26,0.188 10 false *1 2.552,1.583 2.823,1.771 0.271,0.188 10 false *2
*1 Lock Plate
*2 Core


Inspect the lock plate for damage.

If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. Correct any deformations with pliers.

Water will leak if the bottom of the lock plate groove is damaged or dented. Repair or replace it if necessary.

NOTICE:

The radiator can only be recaulked twice. After the second time, the radiator core must be replaced.



Hide 2.INSTALL UPPER RADIATOR TANK AND LOWER RADIATOR TANK

a.
A252179
2.313,1.281 2.594,0.854 2.594,0.854 2.688,0.854 false 2.75,0.76 3.063,0.938 0.313,0.177 10 false *1 1.667,3 1.979,3.167 0.313,0.167 10 false *d 2.677,3 2.969,3.177 0.292,0.177 10 false *d 0.688,3 1,3.167 0.313,0.167 10 false *c 2.188,2.01 2.49,2.177 0.302,0.167 10 false *b 0.698,1.99 0.958,2.167 0.26,0.177 10 false *a
*1 O-Ring
*a CORRECT
*b INCORRECT
*c Normal
*d Twisted


Check that there are no foreign objects in the lock plate groove, and then install a new O-ring. Make sure the O-ring is not twisted.

HINT:

When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.



b.

Install the tank without damaging the O-ring.


c.
A110381
0.771,0.25 0.844,0.25 0.844,0.25 1.125,0.521 true 1.74,0.25 1.646,0.25 1.646,0.25 1.354,0.802 false 0.875,1.198 1.146,1.354 0.271,0.156 10 false *a 2.323,1.198 2.594,1.365 0.271,0.167 10 false *b 0.531,0.135 0.75,0.302 0.219,0.167 10 false *1 1.781,0.135 1.958,0.281 0.177,0.146 10 false *2
*1 Tank
*2 Lock Plate
*a CORRECT
*b INCORRECT


Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and tank.


Hide 3.ASSEMBLE SST

a.
A234961
2.333,0.729 2.563,0.281 2.563,0.281 2.688,0.281 false 2.823,1.115 2.563,1.469 2.563,1.469 2.563,1.688 true 0.594,2.5 0.844,2.771 0.844,2.771 0.844,3.073 false 0.396,2.604 0.396,2.771 false 2.385,2.938 2.385,2.792 false 0.646,1.302 0.938,1.469 0.292,0.167 10 false *1 2.49,1.75 2.76,1.917 0.271,0.167 10 false *3 2.729,0.177 3.01,0.354 0.281,0.177 10 false *2 0.292,2.823 0.625,2.99 0.333,0.167 10 false SST 0.708,3.125 1.073,3.292 0.365,0.167 10 false SST 2.26,2.99 2.604,3.208 0.344,0.219 10 false SST
*1 Dimension B
*2 Part A
*3 Stopper Bolt


Install the punch assembly to part A of the overhaul handle as shown in the illustration.

SST
09230-01010  (09231-01010, 09231-01020)
09231-14010  


b.

While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

8.4 mm (0.331 in.)



Hide 4.CAULK LOCK PLATE

a.
A301819
0.906,2.688 1.333,1.885 1.333,1.885 1.51,1.885 true 2.458,3.854 1.906,3.854 true 2.365,4.073 2.031,4.281 2.031,4.281 1.896,4.281 true 0.792,2.688 0.5,2.688 false 0.948,0.344 1.188,0.5 0.24,0.156 10 false 5 1.708,0.344 1.969,0.5 0.26,0.156 10 false 3 2.469,0.354 2.667,0.521 0.198,0.167 10 false 7 0.073,0.844 0.271,1.042 0.198,0.198 10 false 1 3.292,0.813 3.417,1.021 0.125,0.208 10 false 2 0.958,1.344 1.188,1.521 0.229,0.177 10 false 6 1.74,1.344 1.927,1.5 0.188,0.156 10 false 4 2.49,1.344 2.688,1.5 0.198,0.156 10 false 8 0.167,2.615 0.531,2.813 0.365,0.198 10 false SST 1.563,1.792 1.875,1.99 0.313,0.198 10 false *1 1.635,3.781 1.917,3.979 0.281,0.198 10 false *2 1.635,4.198 1.948,4.396 0.313,0.198 10 false *3
*1 Stopper Bolt
*2 Tank
*3 Lock Plate


Lightly press SST against the lock plate in the order shown in the illustration. After repeating this a few times, fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.

SST
09230-01010  (09231-01010, 09231-01020)
09231-14010  

NOTICE:
·
A208815
0.979,2.49 1.26,2.677 0.281,0.188 10 true (1) 2.875,1.594 3.188,1.781 0.313,0.188 10 true (2) 2.833,1.052 3.094,1.25 0.26,0.198 10 false (1) 2.083,2.49 2.344,2.677 0.26,0.188 10 true (1)

Do not press the protruding areas around the ports (1) and bracket (2).

·
A301820

Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.




b.
A099695
3.198,0.708 3.406,0.865 0.208,0.156 10 false H

Check the lock plate height H after completing the caulking.

Standard plate height H:

8.8 mm (0.346 in.)


If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.


Hide 5.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the drain plug.


b.

Install the drain plug.


Hide 6.INSPECT FOR WATER LEAKS

a.
A099696
2.063,0.313 1.969,0.313 1.969,0.313 1.604,1.188 true 2.781,0.833 3.01,0.833 false 2.177,0.24 2.542,0.417 0.365,0.177 10 false SST 2.448,0.771 2.792,0.938 0.344,0.167 10 false SST

Plug the inlet and outlet pipes of the radiator with SST.

SST
09230-01010  (09231-00030, 09231-00060)


b.

Using a radiator cap tester, apply pressure to the radiator.

Standard test pressure:

177 kPa (1.8 kgf/cm2, 26 psi)



c.

Submerge the radiator in water.


d.
A090282
2.375,1.052 2.688,0.781 2.688,0.781 2.792,0.781 false 1.115,0.333 1.469,0.333 true 1.688,1.844 1.802,1.844 1.802,1.844 2.177,1.635 true 2.844,0.688 3.115,0.865 0.271,0.177 10 false *2 0.906,0.26 1.135,0.438 0.229,0.177 10 false *1 1.448,1.781 1.719,1.927 0.271,0.146 10 false *3
*1 Tank
*2 Lock Plate
*3 O-Ring


Inspect for leaks.

HINT:

On radiators with resin tanks, there is clearance between the tank and lock plate where a small amount of air will remain. This air is released when the radiator is submerged in water, giving the appearance of an air leak. Before performing the water leak test, first shake the radiator in the water until all air bubbles are released.



Hide 7.INSTALL RADIATOR BRACKET SUB-ASSEMBLY

a.

Install the 2 brackets with the 4 bolts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)