Home › Engine / Hybrid System › 2TR-FBE COOLING › COOLANT
RM1840EF _51 Engine / Hybrid System _009596 2TR-FBE COOLING _0052377 COOLANT A

2TR-FBE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE COOLANT

a.

Remove the radiator cap.

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



b.

Loosen the cylinder block drain cock plug and radiator drain cock plug to drain the coolant.

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.


A263383
5.323,0.229 5.208,0.229 5.208,0.229 4.313,1.01 false 5.49,1.771 5.375,1.771 5.375,1.771 3.917,3.083 false 2.917,2.125 1.521,3.01 1.521,3.01 1.396,3.01 false 3.406,1.583 1.771,0.74 1.771,0.74 1.625,0.74 false 5.375,0.167 5.635,0.375 0.26,0.208 10 *1 5.521,1.698 5.833,1.875 0.313,0.177 10 *4 1.219,2.948 1.552,3.167 0.333,0.219 10 *3 1.438,0.677 1.729,0.865 0.292,0.188 10 *2
*1 Radiator Cap *2 Radiator Reservoir
*3 Cylinder Block Water Drain Cock Plug *4 Radiator Drain Cock Plug



Hide 3.ADD ENGINE COOLANT

a.

Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

Torque:
for Cylinder block drain cock plug : 13 N*m (130 kgf*cm, 9 ft.*lbf)

Standard Capacity:
Item Specified Condition
A/T 8.1 liters (8.6 US qts, 7.1 Imp. qts)
M/T 7.8 liters (8.2 US qts, 6.9 Imp. qts)


NOTICE:

Never use water as a substitute for engine coolant.


HINT:
·

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

·

Please contact your TOYOTA dealer for further details.




b.

Fill the radiator reservoir with TOYOTA SLLC to the F line.


c.

Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

If the coolant level drops below the F line, add TOYOTA SLLC to the F line.


d.

Install the radiator cap.


e.

Bleed air from the cooling system.

i.

Warm up the engine until the thermostat opens.

While the thermostat is open, circulate the coolant for several minutes.


ii.

Maintain the engine speed at 2500 to 3000 rpm.


iii.

Press the inlet and outlet radiator hoses several times by hand to bleed air.

CAUTION:
When pressing the radiator hoses:
·

Wear protective gloves.

·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the radiator fan.





f.

Stop the engine and wait until the coolant cools down to ambient temperature.

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



g.

Check the coolant level in the radiator reservoir.

If the coolant level is below the L line, add SLLC up to the reservoir F line.


Hide 5.INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)