Home › Engine / Hybrid System › 1GR-FE COOLING › COOLANT › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009597 1GR-FE COOLING _0052382 COOLANT A

1GR-FE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH

Hide 2.REMOVE ENGINE SIDE COVER SUB-ASSEMBLY RH

Hide 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.DRAIN ENGINE COOLANT

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A110401
1.896,2.719 1.896,3.26 1.896,3.26 1.635,3.26 true 2.063,0.698 2.271,0.698 2.271,0.698 2.271,1.094 false 4.26,0.167 4.198,0.167 4.198,0.167 2.719,1.198 true 3.052,2.271 3.469,3.615 3.469,3.615 3.615,3.615 true 4.083,2.115 4.406,3.219 4.406,3.219 4.635,3.219 true 3.948,1.458 5.531,0.938 5.531,0.938 5.781,0.938 true 1.417,3.188 1.615,3.333 0.198,0.146 10 false *5 4.698,3.146 4.885,3.313 0.188,0.167 10 false *3 1.823,0.615 2.01,0.781 0.188,0.167 10 false *1 4.333,0.083 4.542,0.26 0.208,0.177 10 false *2 3.667,3.531 3.854,3.698 0.188,0.167 10 false *4 5.854,0.854 6.042,1.021 0.188,0.167 10 false *3
*1 Radiator Cap *2 Reservoir Cap
*3 Cylinder Block Water Drain Cock Plug *4 Reservoir Tank
*5 Radiator Drain Cock Plug - -


a.

Loosen the radiator drain cock plug.


b.

Remove the radiator cap and drain the coolant.

HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.



c.

Loosen the 2 cylinder block water drain cock plugs and drain the coolant from the engine.


Hide 5.ADD ENGINE COOLANT

a.

Tighten the 2 cylinder block water drain cock plugs.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


b.

Tighten the radiator drain cock plug by hand.


c.

Add engine coolant.

Standard capacity:

9.8 liters (10.4 US qts, 8.6 Imp. qts)


NOTICE:

Never use water as a substitute for engine coolant.


HINT:
·

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

·

Press the radiator hose inlet and radiator hose outlet several times by hand, and then check the coolant level. If the coolant level is low, add coolant.




d.

Slowly pour coolant into the radiator reservoir until it reaches the F line.


e.

Install the reservoir cap.


f.

Install the radiator cap.*1


g.

Start the engine and stop it immediately.*2


h.

Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3


i.

Repeat steps *1, *2 and *3 until the coolant level does not decrease.

HINT:

Be sure to perform this step while the engine is cold, as air in the radiator hose inlet will flow into the radiator if the engine is warmed up and the thermostat opens.



j.

Install the radiator cap.*4


k.

Set the air conditioning as follows.*5

Measurement Condition
Item Condition
Fan speed Any setting except off
Temperature Toward WARM
Air conditioning switch Off


l.

Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

CAUTION:
·

Wear protective gloves. Hot areas on the parts may injure your hands.

·

Be careful of the fan.

·

Be careful as the engine, radiator and radiator hoses are hot and can cause burns.



NOTICE:
·

Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.

·

Do not start the engine when there is no coolant in the radiator reservoir.

·

Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.

·

If there is not enough coolant, the engine may burn out or overheat.



HINT:
·

Press the radiator hose inlet and radiator hose outlet several times by hand to bleed air while warming up the engine.

·

The thermostat opening timing can be confirmed by pressing the radiator hose outlet by hand and checking when the engine coolant starts to flow inside the hose.




m.

Stop the engine and wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

CAUTION:

Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



n.

If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8


o.

If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the F line.

If the coolant level is below the F line, repeat steps *4 through *8.

If the coolant level is above the F line, drain coolant until the coolant level reaches the F line.


Hide 7.INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 8.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY RH

Hide 9.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY LH