Home › Engine / Hybrid System › 1KD-FTV LUBRICATION › OIL AND OIL FILTER › from 2012.04
RM1840EF _51 Engine / Hybrid System _009600 1KD-FTV LUBRICATION _0052398 OIL AND OIL FILTER A

1KD-FTV LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.REMOVE NO. 2 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Wipe the oil pan and drain plug.


d.

Install a new gasket and the oil pan drain plug.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 3.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A227248
1.583,0.813 0.74,0.26 0.74,0.26 0.646,0.26 true 0.281,0.188 0.729,0.375 0.448,0.188 10 false SST

Using SST, remove the oil filter.

SST
09228-07501  

HINT:

Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



Hide 4.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.

Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.


d.
A060101
1.344,1.406 1.594,1.927 1.594,1.927 1.677,1.927 true 1.74,1.833 2.104,2.01 0.365,0.177 10 false SST

Using SST, tighten the oil filter. Depending on the space available, choose from the following.

SST
09228-07501  

i.

If enough space is available, use a torque wrench to tighten the oil filter.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


ii.

If enough space is not available to use a torque wrench, tighten the oil filter 3/4 of a turn by hand or with a common wrench.



Hide 5.ADD ENGINE OIL

a.

Add new engine oil.

Standard Oil Grade:
Item Oil Grade Oil Viscosity (SAE)
w/o Glow Plug Controller G-DLD1, API CF-4, CF or ACEA B1 - 5W-30
- 10W-30
- 15W-40
- 20W-50
w/ Glow Plug Controller for i-ART API CF-4, CF or ACEA B1 - 5W-30
- 10W-30
- 15W-40
- 20W-50
(5W-30 is best choice for fuel economy and good starting in cold winter.)
for DPF ACEA C2 - 0W-30
- 5W-30


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter change 6.6 liters (7.0 US qts, 5.8 Imp. qts)
Drain and refill with oil filter change 6.9 liters (7.3 US qts, 6.1 Imp. qts)
Dry fill 7.4 liters (7.8 US qts, 6.5 Imp. qts)



b.

Install the oil filler cap.


Hide 6.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.