Home › Engine / Hybrid System › 1KD-FTV STARTING › PRE-HEATING SYSTEM(w/o Glow Plug Controller)
RM1840EF _51 Engine / Hybrid System _009603 1KD-FTV STARTING _0052415 PRE-HEATING SYSTEM(w/o Glow Plug Controller) G

1KD-FTV STARTING  PRE-HEATING SYSTEM(w/o Glow Plug Controller)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT ILLUMINATION DURATION OF GLOW INDICATOR LIGHT

a.

Inspect the light illumination duration.

A113412
3.073,2.365 3.385,2.615 0.313,0.25 10 *b 2.375,0.104 2.646,0.354 0.271,0.25 10 *a 4.865,1.896 5.208,2.094 0.344,0.198 10 (°C) 4.875,2.083 5.198,2.292 0.323,0.208 10 (°F) 2.094,0.385 2.76,0.635 0.667,0.25 10 (sec.) 4.542,1.906 4.833,2.083 0.292,0.177 10 30 3.354,1.917 3.646,2.094 0.292,0.177 10 0 3.563,1.917 3.854,2.094 0.292,0.177 10 5 3.531,2.104 3.917,2.281 0.385,0.177 10 41 2.448,1.917 2.74,2.094 0.292,0.177 10 -22 2.198,1.917 2.49,2.094 0.292,0.177 10 0 2.094,1.74 2.385,1.917 0.292,0.177 10 0.5 2.094,1.542 2.385,1.719 0.292,0.177 10 2.0 2.094,1.375 2.385,1.552 0.292,0.177 10 3.0 2.073,0.667 2.365,0.844 0.292,0.177 10 7.5 4.531,2.094 4.792,2.271 0.26,0.177 10 86 3.281,2.094 3.531,2.271 0.25,0.177 10 32 2.427,2.115 2.813,2.292 0.385,0.177 10 -7.6
*a Light Illumination Duration *b Engine Coolant Temperature


i.

Turn the ignition switch to ON, and then measure the light illumination duration.

Light illumination duration:

Refer to the graph.



ii.

Turn the ignition switch off.

If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.


HINT:

Actual light illumination duration may vary slightly from the graph.




Hide 2.INSPECT PRE-HEATING

a.
A301637
0.26,1.448 0.573,1.604 0.313,0.156 10 false *a 1.781,3.167 2.094,3.323 0.313,0.156 10 false *b 0.51,0.323 0.906,0.5 0.396,0.177 10 false 10.5 0.583,0.865 0.917,1.042 0.333,0.177 10 false 8.4 0.594,1.125 0.99,1.302 0.396,0.177 10 false 7.4 0.594,1.323 0.99,1.5 0.396,0.177 10 false 6.8 0.604,1.885 1,2.063 0.396,0.177 10 false 4.7 0.708,2.448 0.948,2.635 0.24,0.188 10 false 0 0.948,2.854 1.188,3.042 0.24,0.188 10 false 0 1.385,2.844 1.625,3.031 0.24,0.188 10 false 12 1.563,2.844 1.906,3.063 0.344,0.219 10 false 12.5 1.865,2.844 2.208,3.063 0.344,0.219 10 false 13 2.083,2.844 2.427,3.063 0.344,0.219 10 false 13.5 2.5,2.844 2.844,3.063 0.344,0.219 10 false 14.5 2.896,2.823 3.198,3.021 0.302,0.198 10 false (V)
*a Pre-heating Time
*b Battery Voltage


Inspect the pre-heating time.

i.

Turn the ignition switch to ON. Measure how long it takes for battery voltage to be applied to the glow plugs.

Standard Time:
Engine Coolant Temperature Pre-heating Time
40°C (104°F) or higher 1 second
below 40°C (104°F) Refer to the graph
(maximum: 15 seconds)



ii.

Turn the ignition switch off.

If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.




b.

Turn the ignition switch to START. Check that battery voltage is applied to the glow plugs.


c.

While cranking the engine, measure how long it takes for battery voltage to be applied to the glow plugs.

Standard Time:
Engine Coolant Temperature Pre-heating Time
40°C (104°F) or higher 1 second
below 40°C (104°F) Refer to the graph
(maximum: 15 seconds)


If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.



Hide 3.INSPECT AFTER GLOW TIME

a.

Inspect the afterglow time.

A113414
1.208,1.25 1.573,1.438 0.365,0.188 2.583,1.25 2.948,1.438 0.365,0.188 2.677,1.958 2.375,2.75 false 1.125,1.885 0.885,2.771 false 2.135,2.792 3.229,3.073 1.094,0.281 10 false 15 (GREL) (+) 0.677,2.792 1.771,3.073 1.094,0.281 10 false 7 (E1) (-) 1.865,1.042 2.375,1.323 0.51,0.281 10 false *a 4.052,1.146 4.688,1.365 0.635,0.219 10 false (sec.) 1.25,1.271 1.635,1.448 0.385,0.177 10 false C23 2.646,1.271 3.073,1.448 0.427,0.177 10 false G39 4.271,1.448 4.563,1.625 0.292,0.177 10 false 120 4.406,2.302 4.542,2.479 0.135,0.177 10 false 1 4.5,2.469 4.615,2.646 0.115,0.177 10 false 0 4.885,2.469 5.073,2.635 0.188,0.167 10 false 20 4.885,2.615 5.083,2.792 0.198,0.177 10 false 68 5.75,2.615 5.948,2.792 0.198,0.177 10 false 40 5.677,2.479 5.969,2.656 0.292,0.177 10 false 104 4.052,1.844 4.344,2.094 0.292,0.25 10 false *b 6.021,2.604 6.417,2.813 0.396,0.208 10 false (°F) 6.01,2.448 6.469,2.635 0.458,0.188 10 false (°C) 5.365,2.885 5.677,3.083 0.313,0.198 10 false *c
*a Component with harness connected (ECM) *b After Glow Time
*c Engine Coolant Temperature - -


i.

After the engine starts, measure how long it takes for battery voltage to be applied to terminals G39-15 (GREL) and C23-7 (E1) of the ECM.

Standard Time:
Tester Connection Specified Condition
G39-15 (GREL) - C23-7 (E1) Refer to the graph


If the result is not as specified, inspect the ECM, engine coolant temperature sensor, glow plug and glow relay.