Home › Engine / Hybrid System › 2KD-FTV STARTING › STARTER(for DENSO Made)
RM1840EF _51 Engine / Hybrid System _009604 2KD-FTV STARTING _0052423 STARTER(for DENSO Made) G

2KD-FTV STARTING  STARTER(for DENSO Made)  INSPECTION  


PROCEDURE

Hide 1.INSPECT STARTER ASSEMBLY

CAUTION:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


A111845
3.365,2.302 2.865,2.563 2.865,2.563 2.469,2.563 false 3.688,2.313 3.927,2.375 3.927,2.375 4.885,2.375 false 3.583,1.104 4.125,0.458 4.125,0.458 4.542,0.458 true 2.25,2.49 2.51,2.719 0.26,0.229 10 false *1 4.646,0.333 4.906,0.563 0.26,0.229 10 false *2 5.01,2.24 5.271,2.469 0.26,0.229 10 false *3
*1 Terminal 50 *2 Terminal C
*3 Terminal 30 - -


a.

Perform pull-in test.

i.

Remove the nut, and then disconnect the field coil lead wire from terminal C.


ii.

Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.

A111846
2.695,0.389 2.895,0.629 0.2,0.24 10 *a
*a Operation - -




b.

Perform holding test.

i.

When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.

If the clutch pinion gear moves inward, replace the magnet starter switch assembly.

A301443
4.625,0.844 5.708,0.313 5.708,0.313 6.073,0.313 true 4.406,0.365 4.719,0.563 0.313,0.198 10 false *a 6.115,0.208 6.427,0.406 0.313,0.198 10 false *1
*1 Terminal C - -
*a Disconnect - -




c.

Inspect clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.

A111848
2.771,0.479 3.073,0.677 0.302,0.198 10 *a 2.594,1.292 2.865,1.458 0.271,0.167 10 *b
*a Operation *b Disconnect




d.

Perform operation test without load.

i.

Connect the field coil lead wire to terminal C with the nut.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


ii.

Mount the starter in a vise between aluminum plates.


iii.

Connect the battery and an ammeter to the starter as shown in the illustration.

A111849
4.156,1.688 3.146,1.979 3.146,1.979 3.146,2.365 false 4.427,1.792 4.427,2.844 false 3.052,2.458 3.323,2.677 0.271,0.219 10 false *1 4.365,2.896 4.646,3.104 0.281,0.208 10 false *2 4.792,1.906 5.073,2.125 0.281,0.219 10 false *a
*1 Terminal 50 *2 Terminal 30
*a Connect - -



iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

100 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Measure the resistance.

i.
A115023
1.938,2.365 1.74,2.646 false 1.604,2.688 1.844,2.917 0.24,0.229 10 *1
*1 Segment


Measure the resistance between any 2 segments of the commutator.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the starter armature assembly.


ii.
A115024
1.906,2.385 1.635,2.802 false 2.823,2.177 2.688,2.479 false 1.5,2.813 1.719,3.031 0.219,0.219 10 *1 2.594,2.521 2.823,2.698 0.229,0.177 10 *2
*1 Segment
*2 Armature Coil Core


Measure the resistance between each segment of the commutator and the armature coil core.

Standard resistance:

10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



b.
A115025

Inspect circle runout.

i.

Place the armature on V-blocks.


ii.

Using a dial gauge, measure the circle runout.

Maximum circle runout:

0.05 mm (0.000197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



c.
A115026

Using a vernier caliper, measure the commutator diameter.

Standard commutator diameter:

35.0 mm (1.38 in.)


Minimum commutator diameter:

34.0 mm (1.34 in.)


If the diameter is less than the minimum, replace the stater armature assembly.


d.
A115027

Measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, correct it with a hacksaw blade.


e.

Inspect the armature bearings.

i.

Check that the armature bearings rotate smoothly.

If the result is not as specified, replace the stater armature assembly.



Hide 3.INSPECT STARTER YOKE ASSEMBLY

a.
A115028

Inspect the field coil for an open circuit.

i.

Measure the resistance between the lead wire and field coil brush lead.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.



b.
A115030

Inspect the shunt coil for an open circuit.

i.

Measure the resistance between the shunt coil terminals.

Standard resistance:

1.5 to 1.9 Ω at 20°C (68°F)


If the result is not as specified, replace the starter yoke assembly.



Hide 4.INSPECT BRUSH

a.
A115031

Using a vernier caliper, measure the brush length.

Standard length:

15.0 mm (0.591 in.)


Minimum length:

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


Hide 5.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A115033

Inspect the brush insulation.

i.

Using an ohmmeter, measure the resistance between the positive and negative brush holders.

Standard resistance:

10 kΩ or higher


If the result is not as specified, replace the brush holder assembly.



b.
A115032

Take a pull scale reading the instant the brush spring separates from the brush.

Standard spring load:

22 to 28 N (2 to 3 kgf, 4.8 to 6.2 lbf)


Minimum spring load:

13 N (1 kgf, 2.9 lbf)


If the spring load is less than the minimum, replace the brush spring.


Hide 6.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A115056
1.927,0.99 2.021,1.115 0.094,0.125 6 false .
V100135

Free
V100136

Lock


Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter clutch sub-assembly.


Hide 7.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check if the pull-in coil has an open circuit.

i.
A197150
1.604,0.917 1.896,0.552 1.896,0.552 2.073,0.552 true 1.396,1.969 1.396,2.385 1.396,2.385 1.594,2.385 false 2.135,0.469 2.344,0.625 0.208,0.156 10 false *1 1.625,2.292 1.885,2.448 0.26,0.156 10 false *2
*1 Terminal C
*2 Terminal 50


Measure the resistance between terminal 50 and terminal C.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



b.

Check if the hold-in coil has an open circuit.

i.
A197151
1.563,1.729 1.979,1.219 1.979,1.219 2.323,1.219 true 2.417,1.125 2.729,1.292 0.313,0.167 10 false *1
*1 Terminal 50


Measure the resistance between terminal 50 and the switch body.

Standard resistance:

Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.